Vodavi Starplus Hybrid Key Telephone System Installation Manual

RELAY/SENSOR PROGRAMMING (Cont’d) 
A. 
a. 
b. 
c. Programming relay for External Paging: 
Programming Steps 
Press the flex button that corresponds to the 
desired relay to be programmed. 
Dial [i] on the dial pad. 
Press the HOLD button to complete the entry. 
The following message is shown on the display 
phone: 
B. 
a. 
b. 
C. 
d. Programming relay for RAN Starting: 
Programming Steps 
Press the flex button that corresponds to the 
desired relay to be programmed. 
Dial [2] on the dial pad. 
Enter a...

RELAY/SENSOR PROGRAMMING (Cont’d) 
Description 
D. Programming relay for Loud Bell Control: 
Programming Steps 
a. 
b. 
C. 
d. Press the flex button that corresponds to the 
desired relay to be programmed. 
Dial [4] on the dial pad. 
Enter the three-digit station number (100-l 55) 
Press the HOLD button to complete the entry. 
The following message is shown on the display 
phone: 
Where: 
XXX= Station number 
E. Programming relay for CO Line Control: 
Programming Steps 
a. Press the flex button that...

Digital Key Telephone Systems sTARPLUS@ SPD 1426 & 2666 
RELAY/SENSOR PROGRAMMING (Cont’d) 
F. Assign Relay/Sensor Interface Module to a 
station: 
Programming Steps 
a. Press the STA flex button (Button #8). 
b. Enter the three-digit station assignment of the 
relay sensor. 
c. Press the HOLD button to complete the entry. 
The following display is shown on the display 
phone: 
Where: 
YYY= Station Assignment 
To delete a station assignment: 
a. Press the STA flex button (Button #8). 
b. Press the...

sTARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
MISC. SYSTEM PARAMETERS (Cont’d) 
610.8 BAUD RATE ASSIGNMENTS 
Programming Steps 
If Baud Rate(s) are to be assigned: 
1. Press FLASH and dial [15]. The first button will 
be lit and ready for programming Port #1. The 
following message is shown on the display 
phone: 
To program the Baud Rate(s) for Ports #l , #3 or #4: 
Programming Steps 
1. Press the desired PORT # flexible button (But- 
tons #l, #3 or #4) to determine the port to be...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2666 
ACCESS CODE PROGRAMMING 
610.9 ACCESS CODES 
Programming Steps 
If the system is in the programming mode, continue 
using program codes. If starting to program here, 
enter the programming mode. Refer to Sec. 600.2. 
If any Access Codes are to be changed: 
1. Press FLASH and dial [20]. The following mes- 
sage is shown on the display phone: 
A. DISA Access Code 
Programming Steps 
If this feature is to be assigned: 
1. Press the DISA ACCESS CODE...

STARPLUS@ SPD 1428 & 2858 Digital Key Telephone Systems 
MISC. SYSTEM PARAMETERS (Cont’d) 
610.10 STATION MESSAGE DETAIL RE- 
CORDING (SMDR) 
Programming Steps 
If Station Message Detail Recording is to be used: 
1. Press FLASH and dial [21]. The following mes- 
sage is shown on the display phone: 
2. To program SMDR features, use the flexible 
button(s) as defined in the following proce- 
dures. 
3. The SMDR, TYPE, PRINT buttons toggle on 
and off. 
4. After all entries are made, press the HOLD 
button...

STATION MESSAGE DETAIL RECORDING 
(Cont’d) 
C. Character Print Assignment 
Programming Steps Description 
1. Press PRINT FORMAT flexible button (Button 
#3) to determine the print format of SMDR 
records. 
l LED ON = 80 Character is enabled 
l LED OFF = 30 Character is enabled 
2. Press HOLD button to accept the data. 
D. Baud Rate Display 
Programming Steps 
The SMDR Baud Rate is programmed using 
Flash 15 Baud Rate Assignments. Button #4 
will return error tone when pressed. The LCD 
displays the...

STARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
MISC. SYSTEM PARAMETERS (Cont’d) 
610.11 WEEKLY NIGHT MODE SCHEDULE 
Programming Steps 
If entries or changes need to be made to this sched- 
ule: 
a. Press FLASH and dial [22]. The following mes- 
sage will then be shown on the display: 
A. 
1. 
B. 
1. 
2. 
3. 
4. Automatic/Manual Operation 
Programming Steps 
The AUTO/MANUAL flexible button (Button #l) 
LED is lit. 
l LED on= Automatic Night Mode 
l LED off= Manual operation. 
Day of Week...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2868 
810.12 HUNT GROUPS 
A. Hunt Group Programming 
Programming Steps 
If Hunt Groups are to be assigned: 
1. Press FLASH and dial [30]. The following mes- 
sage will be shown on the display: 
2. The top left button in the flexible button field will 
be lit for programming Hunt Group 1 (330). To 
change Hunt Groups or enter a different Hunt 
Group, press the appropriate flexible button 1-8 
(330-337) and perform the following proce- 
dures. 
3. Enter...

sTARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
- 
620.1 
INTRODUCTION 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.2). 
If any CO line features are to be changed: 
a. Press FLASH and dial [40]. The following mes- 
sage is shown on the display phone: 
b. Enter a four digit number for the range of lines 
being programmed. If only one line is being 
programmed, enter...