Vodavi Starplus Hybrid Key Telephone System Installation Manual

Table 600-l Default Values (Cont’d) 
FEATURE 
Select Page A 
Select Page B 
New Station Range (#Is) 
STATION PROGRAMMING; (Cont’d) 
Station ID (O-6) 
COS (day & night) 
Speakerphone (O-3) 
Group Pickup (1,2,3,4) 
Paging 
Zones (1,2,3,4) 
Preset Forward (Sta #) 
CO tine Group Access (O-7) 
LCR Class of Service 
Off-Hook Preference 
Flexible Button Assignments 
Display Button Assignments 
Select Page A 
Select Page B 
New Station Range (#I’s) 
UCD GROUP PROGRAMMING: 
UCD Groups (l-8) 
Alternate UCD Group...

Table 600-l Default Values (Cont’d) 
FEATURE 
Deny Table A 
Allow Table B 
Deny Table B 
Special Table 1 
Special Table 2 
Special Table 3 
Special Table 4 
Area Code for Special Table 1 
Area Code for Special Table 2 
Area Code for Special Table 3 
Display Tables 
LCR PROGRAMMING: 
3-Digit Routing Table 
6-Digit Routing Table 
Exception Code Table 
Route List Table 
Insert/Delete Table 
Daily Start Time Table 
Weekly Schedule Table 
Route for 555-l 212 
INITIALIZE DATA BASE PARAMETERS: 
lnit System...

d. The ON/OFF button LED is lit. The system is 
ready to program. 
Other telephones connected to the system continue 
to function normally. 
. 600.3 
PROGRAM MODE ENTRY (Data Termi- 
nal or PC) 
A data terminal connected to the RS-232C port on 
the CPB or remotely through the on-board modem 
can be used for data base programming. 
When using a data terminal (ASCII or PC capable of 
emulating an ASCII terminal) on-site or locally, to 
program the System: 
a. Press return (enter) on the terminal. 
b. Enter...

sTARPLUS@ SPD 1428 812856 
Digital Key Telephone Systems 
SECTION 610 
SYSTEM PARAMETERS PROGRAMMING 
610.1 SYSTEM TIMERS 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.2). 
If any System Timers are to be changed: Description 
This section describes the procedures and steps 
necessary to program system timers. 
The buttons on the digital terminal are defined as 
shown below when...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2656 
SYSTEM TIMERS (Cont’d) 
A. System Hold Recall Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the SYSTEM HOLD RECALL TIMER 
flexible button (Button #l). The following mes- 
sage is shown on the display phone: 
, 
2. Enter three digits on the dial pad. 
3. Press HOLD button. Display will now update. 
B. Exclusive Hold Recall Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the EXCLUSIVE HOLD RECALL TIMER...

STARPLUS@ SPD 1428 & 2858 Digital Key Telephone Systems 
SYSTEM TIMERS (Cont’d) 
C. Attendant Recall Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the ATTENDANT RECALL TIMER flex- 
ible button (Button #3). The following message 
is shown on the display phone: 
2. Enter two digits on the dial pad. 
3. Press HOLD button. 
D. Transfer Recall Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the TRANSFER RECALL TIMER flexible 
button (Button #4). The following message...

Digital Key Telephone Systems %ARPLUS@ SPD 1428 & 2866 
SYSTEM TIMERS (Cont’d) 
E. Preset Forward Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the PRESET FORWARD TIMER flexible 
button (Button #5). The following message is 
shown on the display phone: 
2. Enter two digits on the dial pad. 
3. Press HOLD button. Display will now update. 
F. Call Forward No/Answer Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the CALL FORWARD NO/ANSWER 
TIMER flexible button...

STARPLUS@ SPD 1428 & 2858 
Digital Key Telephone Systems 
SYSTEM TIMERS (Cont’d) 
G. Pause Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the PAUSE TIMER flexible button (But- 
ton #7). The following message is shown on the 
display phone: 
2. Enter one digit on the dial pad. 
3. Press HOLD button. Display will now update. 
H. Call Park Recall Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the CALL PARK RECALLTIMER flexible 
button (Button #8). The following...

Digital Key Telephone Systems STARPLUS@ SPD 1428 & 2858 
SYSTEM TIMERS (Cont’d) 
I. ConferenceIDISA Timer 
Programming Steps 
If this timer is to be changed: Determines the Description 
amount of time an unsupervised 
continue after the initiator of the 
1. Press the CONFERENCEIDISATIMER flexible conterence can 
button (Button #9). The following message is conference has exited the conference. 
shown on the display phone: Default: Default is 10 minutes and is variable from 
01 to 99 minutes. 
A 00 entry...

STARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
SYSTEM TIMERS (Cont’d) 
K. CO Ring Detect Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the CO RING DETECT TIMER flexible 
button (Button #ii). The following message is 
shown on the display phone: 
2. Enter one digit on the dial pad. 
3. Press HOLD button. Display will now update. 
L. SLT DTMF Receiver Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the SLT DTMF RECEIVER TIMER flex- 
ible button (Button...