Vodavi Starplus Hybrid Key Telephone System Installation Manual

Digital Key Telephone Systems STARPLUS@ SPD 1428 & 2866 
SYSTEM TIMERS (Cont’d) 
M. Message Wait Reminder Tone 
Programming Steps 
If this feature is to be changed: 
1. Press the MESSAGE WAIT REMINDERTONE 
flexible button (Button #13). The following mes- 
sage is shown on the display phone: 
2. Enter three digits on the dial pad. 
3. Press HOLD button. Display will now update. 
N. SLT Hook Flash Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the SLT HOOK FLASH TIMER flexible 
button...

STARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
SYSTEM TIMERS (Cont’d) 
0. SLT Hook Flash Debounce Timer 
Programming Steps 
If this timer is to be changed: 
1. Press the SLT HOOK FLASH DEBOUNCE 
TIMER flexible button (Button #15). The follow- 
ing message is shown on the display phone: 
2. Enter a three digit number on the dial pad. 
3. Press HOLD button. Description 
This timer determines the length of time that is 
needed to determine a valid on hook or off hook 
condition for single line...

Digital Key Telephone Systems STARPLUS@ SPD 1428 & 2866 
610.2 SYSTEM FEATURES PROGRAMMING 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec.600.2). 
If any System Features are to be changed: 
1. Press FLASH and dial [05]. The following mes- 
sage is shown on the display phone: Descriotion 
This section describes the procedures and steps 
necessary to program System Features. 
The...

STARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
SYSTEM FEATURES (Cont’d) 
A. Attendant Override 
Programming Steps 
If this feature is to be changed: 
1. Press the AlTN OVERRIDE flexible button 
(Button #l). It will toggle on and off with each 
depression. 
l LED off = Attendant Override is disabled 
l LED on = Attendant Override is enabled 
2. Press HOLD button. The display will update. 
B. Hold Preference 
Programming Steps 
If this feature is to be changed: 
1. Press the HOLD PREF flexible...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2866 
SYSTEM FEATURES (Cont’d) 
C. External Night Ring 
Programming Steps 
If this feature is to be changed: 
1. Press the EXT NIGHT RING flexible button 
(Button #3). It will toggle on and off with each 
depression. 
l LED off = Ext. Night Ring is disabled 
l LED on = Ext. Night Ring is enabled 
2. Press HOLD button. The display will update. 
D. Exec Override Warning Tone 
Programming Steps 
If this feature is to be changed: 
1. Press the EXEC OVER WARN...

STARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
SYSTEM FEATURES (Cont’d) 
E. Page Warning Tone 
Programming Steps 
If this feature is to be changed: 
1. Press the PAGE WARN TONE flexible button 
(Button #5). It will toggle on and off with each 
depression. 
l LED on = Page Warning Tone is enabled 
l LED off = Page Warning Tone is disabled 
2. Press HOLD button. Display will now update. Description 
Determines whether a page warning tone will be 
sounded over the Key Telephone speakers or exter-...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2666 
SYSTEM FEATURES (Cont’d) 
G. LCR Enable 
Programming Steps 
If this feature is to be assigned: Description 
If Least Cost Routing is to be 
1. 
2. Press the LCR ENABLE flexible button (Button 
#7). It will toggle on and off with each depres- 
sion. 
* LED on = LCR is enabled 
l LED off = LCR is disabled 
Press HOLD button, Display will now update. enabled here. Before enabling 
. . - _ _. ,. . used, it must be 
LCR, refer to the 
Least Cost...

STARPLUS@ SPD 1426 & 2656 
MISC. SYSTEM PARAMETERS 
610.3 AlTENDANT STATION ASSIGNMENT 
Programming Steps 
If Attendant Stations are to be changed: 
a. Press FLASH and dial [lo]. The following mes- 
sage is shown on the display phone: 
b. Enter up to three (3) three-digit station num- 
ber(s) on the dial pad. 
c. Press HOLD button. 
610.4 SElTING SYSTEM TIME AND DATE 
Programming Steps 
To set the time and date which appears on display 
Digital Terminals: 
a. Press FLASH and dial [i 11. The following...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2856 
MISC. SYSTEM PARAMETERS (Cont’d) 
610.5 PBX DIALING CODES 
Programming Steps 
If PBX Dialing Codes are to be assigned: 
a. Press FLASH and dial [12]. The following mes- 
sage is shown on the display phone: 
b. Enter 54.~0 digit code numbers, one right after 
the other, on the dial pad up to a maximum of 
ten digits. 
c. Press HOLD button. 
610.6 EXECUTIVE/SECRETARY PAIRS 
Programming Steps 
If Executive/Secretary pairs are to be assigned: 
a. Press...

sTARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
MISC. SYSTEM PARAMETERS (Cont’d) 
610.7 RELAY/SENSOR PROGRAMMING 
Programming Steps 
If Relays are to be assigned: 
a. Press FLASH and dial [14]. Relay #l (Flex 
Button #l) and On-Board Relays (Flex Button 
#1 1) LED’s will be lit indicating the system is in 
the programming mode for “On-Board” relay 
programming. The following message is shown 
on the display phone: 
To program “On-Board” relays: 
a. Press the “On-Board” Relays (Flex Button #1 1)...