Vodavi Starplus Hybrid Key Telephone System Installation Manual

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2856 
Initialize Data Base Parameters (Cont’d) 
H. Initialize LCR Tables 
Programming Steps 
If LCR Tables need to be initialized: 
1. Press the LCR Tables flexible button (Button 
#7). The following message will be shown on 
the display phone: 
2. To initialize the LCR Tables, press the HOLD 
button. Confirmation tone will be heard. Description 
The LCR Tables may be initialized setting all tables 
to their original, default values. The following tables...

STARPLUS@ SPD 1428 & 2858 
Digital Key Telephone Systems 
Initialize Data Base Parameters (Cont’d) 
I. Initialize Entire System and Reset (all pa- 
rameters) 
Programming Steps 
If System needs to be initialized: 
1. Press the System and Reset flexible button 
(Button #8). The following message will be 
shown on the display phone: 
2. To initialize the entire system data base, press 
the HOLD button. The system will perform a 
hard reset. Description 
To completely initialize the data base area including...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2866 
Initialize Data Base Parameters (Cont’d) 
J. Initialize ICLID Table 
Programming Steps 
If the ICLID Table(s) need to be initialized: 
1. Press the ICLID TABLE flexible button (Button 
#9). The following message will be shown on 
the display phone: 
2. To initialize the ICLID Table(s), press the HOLD 
button. Confirmation tone will be heard. Description 
660-12 Issue 1, November 1891  

sTARPLUS@ SPD 1428 & 2856 
Digital Key Telephone Systems 
SECTION 665 
PRINTING SYSTEM DATA BASE PARAMETERS 
A. Introduction 
Programming Steps 
If the system is in the programming mode, continue 
using the program codes. If starting to program here, 
enter the programming mode. (Refer to Sec. 600.2). 
If Data Base Parameters need to be printed: 
1. Press FLASH and dial [85]. The following will 
be shown on the display phone: Description 
This section describes the procedures and steps 
necessary to...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2856 
System Data Base Printouts (Cont’d) 
B. Printing System Parameters 
Programming Steps 
If a printout of all System Parameters is desired: 
1. Press the SYSTEM PARAMETERS flexible 
button (Button #I). The following message will 
be shown on the display phone: 
2. To print the system parameter data base, press 
the HOLD button. The display will update. 
When the system has finished sending the informa- 
tion to the printer, confirmation tone will be...

STARPLUS@ SPb 1428 & 2856 
Digital Key Telephone Systems 
2856 Digital Key-System 
Eng. Ver. O.lH 
DATE: MM/DD/YY TIME: HH:MM:SS 
ZF pAsswom: 
kNTER PROGRAM NO 
2 NONE 3 NONE 4 NONE 5 NONE 6 NONE 
RELAY/SENSOR ### 
a-85 
PRINT DATA-BASE 
EWIERBUMONNUMBERB 
adm>q 
PRINTING SYS PARAM 
adm%YSTEMPARAM.ErERS 1 NONE 
2 NONE 3 NONE 4 NONE 
2 E-i-E 
Eng. Ver. O.lH 
SYSTEM TIMERS 
SHREHRARTXFRPFTCFN FI 
60 180 1 45 10 15 2 I/O BAUD RATES 
PORT l/ON BOARD= 
FORT 2/MODEM= 
FORT 3/RS232= 
PORT 4/RS422= 
CPTCFT...

Digital Key Telephone Systems sTARPLUS@ SPD 1428 & 2856 
System Data Base Printouts (Cont’d) 
C. Printing CO Line Attributes 
Programming Steps 
If a printout of the CO tine Attributes is desired: 
1. Press the CO LINE ATTRIBUTES flexible but- 
ton (Button #2). The following message will be 
shown on the display phone: 
2. To print the data for ALL CO Lines, press the 
HOLD button. To print CO Line data for a 
specified CO Line Range enter four digits to 
specify the CO Line range (two digits for the...

STARPLUS@ SPD 1428 & 2856 Digital Key Telephone Systems 
2856 Digital Key-System 
Eng. Ver. O.lH 
DATE: MM/DD/YY TIME: HH:MM:SS 
ENrERPAbwORD: 
ati, 
ENTER PROGRAM NO 
:zt5 
PRINT CO LINES 
PRESS HOLD 
adrrv 
PRINTINGCO LINES 
CO LINE ATTRIBUTES 
co 1 
Description 
SI@?ATJ TYPE UNA CONF PRI 
m co Y Y Y 
SUPV DISA FLY GRP COS 
N N 1 1 
RING ASSIGNMENTS 
100B 
co 2 
SIG&L TYPE UNA CONF PRI 
co Y Y Y 
SUPV DISA FLTM GRP COS 
N N 10 1 1 
RING ASSIGNMENTS 
100B 
co 3 
SIGNAL TYPEUNACONF PRI 
m co Y Y Y 
SUPV...

Digital Key Telephone Systems STARPLUS@ SPD 1428 & 2858 
System Data Base Printouts (Cont’d) 
D. Printing Station Attributes 
Programming Steps 
If a printout of the Station Attributes is desired: 
1. Press the STATION ATTRIBUTES flexible but- 
ton (Button #3). The following message will be 
shown on the display phone: 
2. To print data for all stations, press the HOLD 
button. To print Station data for a specified 
Station Range enter six digits to specify the 
Station range (three digits for the first...

2856 Digital Key-System 
Em. Ver. O.lH 
DA+E: MM/DD/YY TIME: HH:MM:SS 
ENTER PASSvxxxD: 
a*, ENTER PROGRAM NO 
ad85 
afhnx 
PRINTING STATIONS 
STATION ATTRIBUTES 
STA 100 
PAGE DND COW-EOR PRI SPD QUE 
PL3:O~OFzDLc:: N Y Y 
S:D AI: IX& N:OS SPK 
0 1 
0 
PICKUP PAGE PREhD LCOS 
1 1 N 
CO ACCESS 1 
BUTION 
OlDlOO 
04D103 
07D106 
z% 
16COO6 
19PLl 
22LQu 
%E S 
02DlOl 03D102 
05D104 06D105 
08D107 09D108 
11c001 12coo2 
14coo4 15coo5 
17coo7 18COO8 
2OLP 21cJ?o 
23CBK 24PKU 
26FWD 27DND 
PRIME KEY 0 Y 
STA...