Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

- 
irlfinite Dd and DVX” 
Di&it&I key Tclephonc Systems 
~xlkI CALL DISTRIBUTION (Cont’d) 
UCD TIMERS (Cotit’d) 
F. UCD No-mer Retry Timer 
Pro- Steps 
To make a change to the UCD No-Answer Retry 
Timer: 
1. Press the NO-ANSWERRElR’Y~~Rflcx- 
ible button (FJutton #6). The followlngmes- 
sage is shown on the display phone: 
71 
2. Enter the three-digit value on the dial pad 
which corresponds to 000-999 seconds. 
3. Press the HOLD button to save the entry. 
Confhxnation tone is heard and the dispIay 
wIll...

i+ite DVX’ md DVX” 
D&i&l Key Telephone Systcme UNJJFORM CALL DISTRIBUTION (UCD) 
I~NI~$GN~I CALL DISTRIBUTION (Cont’d) 
745.3 UCD RAN ANNOUNCEMENT TA- 
BLES 
Rograrmning Steps 
lf Recorded Announcement devices are in- 
stalied to operate with UCD. these tables must 
be programmed: 
a. Press FTASH and dial [62]. The following 
message is shown on the display 
phone: 
-nj 
b-The top left button in the flexible button 
field will be tit for programmmg UCD RAN 
Announcement 
Table 1. To change to UCD 
RAN...

mite DVX’andDVX’ 
wtfd Key Telephone Systems ICIJD PROGRAMMING 
SECTION 750 
ICLID PROGRAM-G 
750.1 INTRODUCTION 
The ICLID @ncoming Calling 
Line IDentica- 
iion) feature has been added to the infinite 
DigkaI Key Telephone System. The operation of 
this feature is dependent on the feature first 
being activated kom the central office so that 
the numbers of the calling party will be deliv- 
ered over the individuat tip and ring of the CO 
Itnes during the first siknt interval between 
ringing. The...

ICLJDPROG-G 
iqjinite DVX’andDVXn 
D&&al Key Telephone Systems 
FUlCtiOIl Function 
3utton 
1. GO to be&min~ of list ) DialCode 
635 
2. Review next item in this 
3. Step to next list en-. HOLD 
4. Delete this list entry. FLASH 
5. Delete entire list. 1 Note’ . 
6. Exit list review function. ON/OFF 
7. Step to previous list entry, TRANS : 
18. Call Back. 1 SPEED 1 
’ This feature is only available to the 
Attendant(s) st.aUcm[s) to clear the list one 
entry at a time. 
. 
760-2 
Issue 1. January 1993  

[email protected] DVX’andDVXn 
D&&al kzcy Telephone Systems ICLID PROG~G 
ICLID PRoG I~AMMING (Cunt’d) 
750.2 ICIJD RINGING ASSIGNMENT 
If ICIJD Ringing Assignments need to be as- 
signed or changed: 
1, 
press FLASH and dial [43]. The following 
message is shown on the display phone: 
where: 
- 
OO= ICUD Route Number 
00-09 for DVX I System, 00-20 
for 
DYX ’ System 
- 
XxXY= ICLID De&nation @OR) and 
Rixghg Assignment Kl 
2. Press the RING ASSiGNMEWT flexible but- 
ton (Button # 1). LED #l is 
lit indicating...

iqfhtite DVX’andDVXn 
Digital Key Telephone 
Systems 
Propnnning Steps 
ping assfgnments witl be continuous and w-ill 
be displayed in order of the destination number 
f?om 001 to 557. 
&Repeat Step 3 to program additional sta- 
tions and rIngi.ng ass@ments. A maxi- 
mum of eight stations wilS &splay on the 
LCD display. Additionat stations and ring- 
ing assignments can be displayed using 
Button # 17. 
To advance to the next Route: 
1. Press the NEXT flexible 
button (Button 
#l$) to advance to the...

XCLID PRoG RilNMXNG [Cont’d) 
7so.3 ICLID FEkmmEs 
Programming 
Steps 
If ICLID is to be used: 
1. Press FLASH and dial [SS]. The following 
message is shown on the display phone: 
2. To program ICLJD features, use the flexibie 
button(s) as defined in the following proce- 
dures. The ICLID. NAME buttons toggle on 
and off. 
3.After all entries are made, press the HOLD 
button to accept the data. 
Prow steps 
1. Press the ICLID ENABLE flexible button 
(Button # 1). This feature will toggle on and 
off...

iqfiniie DvX’andDVX” 
DQfiM Key Telephone Systems 
ICIJD PROG RABUMING (Ccmt’d) 
ICUD Features {Ckmt’dI 
prog - g steps 
C. 
Baud Rate Display 
The ICLJD Baud Rate is programmed using 
Flash 15 Baud Rate Assignments. Button 
#3 will return error tone when pressed. The 
LCD displays the current baud rate based 
on which Port number is assigned to the 
iCLID Port number. 
D. Port Atmi@mcnt 
prO@3Imliq~ steps 
1. Press the PORT flexible button (Button #4) 
to determine which port is to be used for 
ICLID...

irtfirrite DVX’ and DVX’ 
DQ$tal Key Telephone Systems VOICE I&AIL GROUPS (VMj 
SECTION 755 
VOICE MAIL GROUPS m) 
755.1 VOICE MAIL. PROGRAM?HING 
Pro@ammin~ Steps 
If the system is in the programming mode, 
continue using the program codes. If starting to 
program here, enter the programming mode. 
Refer to Sec. 700.2, Program Mode Entry 
(Key 
Station). 
If Voice Mail Groups are to be programmed: 
1. Press FLASH and dial (651. The following 
message is shown on the display phone. 
‘31 
W-ha: 
- G =...

VOICE MAIL GROUPS W 
infinite DVX’ and DVX” 
D&~&II Key 
Telephone Systems 
A ANnnate Voice Mail Group 
Profpmming Steps 
To program an alternate group: 
1. Press the ALTERNATE VM GP flexible but- 
ton (Button #9). 
2. Enter the three-digit pilot number (440 to 
447) of the desired group. 
3. Aess the HOLD button to save the entry. 
Con&mat&m tone is heard and the display 
will now update. 
B. ‘leave” Mail Index Entry 
l?rof$ * g steps 
To specitjr the “Leave” mail index (outpulsing 
table) to be...