Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

f@&e IWX’andDVXn 
D&im IKey Telephone Systems AUTOMATIC CALL DISTRIBUTION (ACD] 
AuTohfA~c CALL DISTRIB~~N (Cont’d) 
740.3 ACD RAN ANNOUNCEMENT TA- 
BLES 
If Recorded Announcement devices are in- 
stalled to operate with ACD. these tables must 
be programmed: 
a. Press FLASH and dial (621. The 
following 
message is shown on the display phone: 
b-The 
top left button in the fkible button 
field will be 
lit for programming ACD RAN 
Announcement Table 1. To change to ACD 
RAN Announcement Table 2, press...

imite DVX’ aad DVX” 
Digital Key Telephone Systems 
A~o&%i@f’Ic CALL DISTRIBUTION (Cont’d) 
740.4 PC/ACD INTERFACE TRACE 
Programming Steps 
To enable PWACD Interface Trace options: 
1. Press FL4SH and dial 163). The following 
message will be shown on the display 
phone: 
- X= Port for PC/ACD lnterfaqz ?kace 
- YYYY= Baud Rate of desired port. 
A. Event Trace 
En2hlt/Dis2ble 
Prop * L-J steps 
1. Press the PC/ACD EVENT TRACE flexible 
button (l3utton # 1). It will toggle on and off 
with each...

i-&e DVX’andDVX’ 
Digftal Key Telephone Systems AUTOMATIC CALL DISTRIBUTION (ACDI 
Amoh’IAmc CALL DIWFUBUTION (Cont’d] 
Pc/ACD INTERFACE TRACE Hhnt’d) 
B. T-race Port Assignment. 
Prop- Steps 
I. Press the PC/ACD PRINT POW flexible 
button [Button #2) to determine which port 
is to be 
used for the PC/ACD interface 
Trace. 
2. Enter a one-digit number for the PC/ACD 
Event Trace Port number: 
- 1= Port # 1 (“On-Board” RS-232C) 
- 2= 
Port #2 (“On-Board” Modem) 
- 
3= Port #3 0/O Expander Module 
RS-232C)...

iqfutite DVX I and DVX Ii 
Dma Key Telephone 
sy8tCIIiS UNIFORM CAU DIST2ZlBUTIoN (UCD) 
SECTION ‘745 
UNIFORM CALL DISTRIBUTION (UCD) 
745.1 UCD GROUP PROGRAMMING 
FYogrixmdng Steps 
lf the system is in the programmhg mode, 
continue using the program codes. If starting to 
program here, enter the programming mode. 
Refer to Sec. 700.2, Program Mode Entry (Key 
Station). 
If UCD Groups are to be assigned: 
1. Press FLASH and dial [601. The following 
message is shown on the display phone: 
Where: 
- X=...

~C3~bl CALL DISTRIBUTION rVCD) &finite DVX I and DVX II 
DigitaI &v Telephone Sy&ems 
UNIFORM CALL DISTl3IBU’l’ION (Cmt’d) 
A Alttrnnte UCD Group Assignment 
Programming Steps 
To program an alternate group: 
1. press the ALTERNATE UCD GP flexible 
button (Ektton #9). 
2. Enter the three-digit pilot number (550 to 
557) of the desired alternate UCD group. 
3. Press the HOLD button to save the entry. 
Confirmation tone is heard and the display 
will now update. Description ALTERNATE UCD GROUP. An...

infinite DVX’ and DVX’ 
D@tal Key Telephone Systems UNIFORM CZ.AIL DISTREKJTION @ED) 
ARM CALL DXSTRIBUTION 
[Cont’dI 
c. UCD Recorded Announcement 
~~cntbl mm 
Pxgrammir* steps 
To program a Recorded Announcement: 
1. Press the ANNOUNCEMENTTBLS flexible 
button (Button # 11. 
2. 
Enter one of the following digit sequences: 
- 
l# = RAN port specified in Table 1 
will be used. 
- through 
- 8# = RAN port specified in Table 8 
will be used. 
Example: 
- 1,2=Port1wiIlanswe.rthecall;port 
2 will provide a...

iqjinite DVX ’ and DVX’ 
WORM CALL DISTRIBUTION (Cont’d) 
D. UCD Station Assignment(s) 
Pro@ * g Steps 
To program stations into a UCD group: 
1. Press the Page “B” flexible button (Page A 
Button # 
19). The following message is 
show-n on the display phone. 
ul3l3913 #### #Hi@ #I## #I## 
H# ### ### ### 
Where: 
- X= IJCD Group Number (l-8) 
- B= Page -B” parameters 
- ###= UCD Station ass~ents 
2.The top l& button in the flsdble button 
fieldwillbelitforpro&rammlng UCD group 
0 (550). To change UCD...

UNJFoRM CALL DISTRIBUTION (Cont’d) 
745.2 UCD TTBBEKS 
Programming steps 
If UCD timers are to be changed: 
a. Press F-H and dial [61]. The follawing 
message is shown on the display phone: 
A. UCDRiqTimer 
B steps 
To make 
a change to the UCD Ring ‘Inner: 
1. Press the FUNG TIMER 
flexible button (But- 
ton # 1). The following message is shown on 
the display phone: 
2. Enterthe three-digit tfmervalue on the dial 
pad which corresponds to 060-300 see- 
onds. 
3. Press the 
HOLD button to save the...

FORM CALL DISTRIBUTION (UCD) 
iqfinite DvX’andDVX” 
a&&al Key Telephone Systems 
-RM CALL DISTFEIIXJTION (Cont’d) 
UCD TIMERS (Cont’dl 
B. 
UCD Message httd Timer 
FYogEmming steps 
To make a change to the UCD Message Interval 
Timer: 
1. F’ress the MITTIMER flexible button (But- 
ton #2). The following message is shown on 
the display phone: 
2. Enter the three-digit timer value on the dial 
pad which corresponds 
to 000-600 sec- 
onds. 
3.Press tie HOLD button 
to save the entry. 
Confirmation tone is...

imite DVX’ and DVX” 
Dj&d Key Telephone Systems 
UNJPORM CAL% DISTRIBUTXON (UCD] 
UNTF-ORM CALL DISTRIBUTION (Cm&d) 
UCD TIBXERS (Cont’d) 
D. UCD Auto Wrap-Up 
Timer 
I?4-ogramdng steps 
To make a change to the UCD Auto Wrap-up 
Timer: 
1. Press the AUTO-WRAP TIMER fiexible but- 
ton (EMton #4). The following message is 
shown on the display phone: 
2. Enter the three-digit value on the dial pad 
which corresponds to OCG6OO seconds. 
3Jres-s the HOLD button to save the 
enhy. 
Confirmation tone is heard...