Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

sys~‘~M PARAMETERS PROGRAMMING 
@finite DVX’andDVX” 
Digital Key Telepbonc Systems 
MISC. SY?xFcM P ARAMmERs (Cont’d) 
DIRECTORY DIALING (tint ‘d) 
To enter the Intercom number or system speed 
dial bin to be associated to the name: 
Projpmming Steps 
1. Press the BIN/ICM fl&ble button (Button 
#ll. 
2. Enter a three-digit station intercom num- 
ber (100-155) or 
Enter a three-digItSystem speed dial num- 
ber (020-099). 
Enter a three-dgit Local Number/Name 
Translation Table number (300-499). 
3.Press...

iqjhitt? DVX’andDVXn 
DQm Key Telephone Systems 
smnu PAIWMETERS PROGRABUMNQ 
MISC. SYSTEM Pm (Cont’d) 
DIRECTORY DIALING (Co&d) 
To ckar an entry: 
Prog -lgsteps 
1 -Press the CW flexible button (Button 
#3). 
2. 
Press the HOLD button to save the entry. 
Conffrmation 
tone is heard and the display 
wiU now update. The em-y will be erased 
(both the BIN/ICM assignment and the 
programmed name). Description 
CLEAR - Entries in the table may be erased and 
cleared from the table allowing another entry to...

.; 
SYSTEM PARAM.EE= PROGRAMMING &finite DVX’ and DVX’ 
D&&al Key Telephone Systems 
MISC. SYSTEM PARAMETE RS (Cont’d) 
710.13 EruNT GROUPS 
1f Hunt Groups are to be assigned: 
f . Press FLASH and dial f30J. The following 
message wiIl be shown on the display: 
2.The top left button in the fle&ble button 
field will be lit for programming Hunt 
Group I @30). To change Hunt Groups or 
enter a &f&rent Hunt Group. press the 
appropriate flexible button 1-S (330-337) 
and perform the following procedures....

iqfinite DV2C’andDVX” 
Di@td Key Telephone Spstems 
SYSTEM P-RS PRUGIlAMMING 
MISC. SYSTEM PARAMETE 
RS (Cont’d) 
7 10.14 LUCAL NlJMBER/NAME TRANSIA- 
TIUN TABLE 
Proffrarnrning Steps 
lf changes need to be made to Local Num- 
ber/Name Translation Table: 
1. F’ress FLASH and dial 1551. The following 
message is shown 
on the display phone: 
]I 
mere: 
- XXX= Table Number 300-499 
- ##= Route Number 00-19 
2.The ROUTE NUMBER LED is lit. Enter the 
two-digit Route 
Numbu (00- 191 frm what 
was entered in...

. 
@finite DVX’ and DV2X” 
8YsTEM PARAMETERS PROGRAMMlNG [email protected] Ecy Telephone Systems 
MISC. SYSTEM PARAMETE 
FtS (Cont’d) 
LOCAL NAME TRANSLATION [Cont’d) 
Pm@ * .,steps 
To progmm a phone number into the Local 
Number/Name Translation table: 
1. Press the PHONE NUMBER flexible button 
(E&.&ton #2) to enter the desired phone 
number into the translation table. Maxi- 
mum length of phone number is I$-digits, 
including hyphens. 
D =31 
E=32 
F=33 
G =41 
H =42 
I -43 
J =51 
K =S2 
L =53 M =61 
N =62...

_ _ . . 
i@zite DVX’ and DV2C” 
D&itd Key Telephone Systema SYSTEM PARAMETERS PROGIUUKMING 
MISC. SYsrnM PA,IuMEm RS (Cmt’d) 
LOCAL NAME TRANSLATION (Cont’d) 
Rogrammiry! Steps 
To progam a name into the translation table: 
1. Press the PJAME flexible 
button mutton #3) 
to enter the 
desired name into the transla- 
tion table. Maximum Iergth is 2-+charac- 
ters. 
A=21 M561 
B -22 
N -62 
C=23 0=63 
D=31 
f =?l 
E =32 Q =?4 
F =33 
G =41 
H =42 
I=43 
J =51 
K =52 
L=53 
R =72 
s =73 
T =81 
u =82 
v=a3...

r 
in_finite DVXandDVX 
D~~KeyTclepho~eS~telIlB CO LINE ATITUBUTES PROGRAMMING 
SECTION 720 
CO LINE ATTlUBUTES PROG-NG 
720.1 ~ODUGTION 
l?rogramming steps 
If the system is in the progr * ’ g mode, 
continue using the program codes. IfstarLing to 
program here, enter the programming mode. 
Refer to See. 700.2, Program Mode Entry (Key 
Station). 
If any CO line features are to be changed: 
a. Press FLASH and dial 1401. The following 
message is shown on thgt display phone: 
51 
b. Enter a four-digit...

r 
CO LINE ATTRIBUTES PROG-G [email protected] DVX’ and DVX” 
[email protected] Key Telephone Systems 
co LINE A’ITRTBUTES [C-onYd) 
A DTMF/Dial P&e Progmz 
Profprmming Steps 
1. Press the DTMF/DIAL PULSE flexible but- 
ton fButton 
#l]. This feature will toggle on 
and off with each depression. and the dis- 
play will update with each depression. 
l LED on = DTMF enabled 
l IlED off= l&I Pulse enabled 
2.Ress the HOLD button to save the entry. 
B. CO/PBX programming 
ROgI ’ lg steps 
1. Press the CO/PBX flexible button...

r 
iJZFn@e DVX’ and DVX If 
digital Key Telephone Systems CO l.JNE ATTRIBUTES PROGIUBKMING 
CO LINE ATTRIBUTES (Cont’d) 
Pro@krmning Steps Description 
1. Press the UNA flexible button Button #3). 
This feature will toggle on and off with each 
depression, and the display will update 
with each depression. 
l LJSD on = UNA is enabled 
. LED off= UNA is disabled 
2. Press the HOLD button to save the entry. 
Confirmation tone is heard. UNA. If a line is marked UNA, and if the system 
is in night setice...

iqj%ite DVX ’ and DVX I1 
co z;LNE AWUTE!j PROGRAMMING 
Dig&al Key Telephone 
Systems 
co LINE ATTRE3UTES @unt’dI 
E. privacy 
Pro@ ~‘gsteps 
If CO L.ine privacy is to be changed: 
1. Press the PRIVACY flexible button. (Button 
#5, This feature will toggle on and off with 
each depression. and the display will up- 
date with each depression. 
* IED on = Privacy is enabled 
* LED 0s = Privacy is disabled 
2. Press the HOLD button to save the entry. 
Confirmation tone is heard. Description 
RRIVACY. If...