Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

SYSTEM PARAMETERS PROGRAMhUNG Di&al Key Telephone Systems 
SYSTEM FEATURES [Cont’dl 
C. Erternnl Nfght Rixq 
Programming Steps 
If this feature is to be changed: 
1. Press the FXFNIGHTRING flexible button 
(Button #3). This feature will toggle on and 
off with each depression, and the display 
will update with each depression. 
+ LED off = Ext. Night F&g is disabled 
l LEDon= Ext. Night Ring is enabled 
2. 
Press the HOLD button to save the entq. 
Confi.iation tone is heard. 
D. Executive Override Wmdmg...

r 
iqfini.teDVX1andDVXn 
Digital Xey Telephone Sys&n.s 
Sl’STEM PARULETERS PROGRAMMING 
SYSTEMFEATURES(Contd) 
E. Page Warning Tone 
Progrsmming Steps 
If this feature is to be changed: 
1, Press the PAGE WARN rONE ilexible but- 
ton (Button #51. This feature will toggle on 
and off with each depression, and the dis- 
play will update with each depression. 
. LED on = Page Warning Tone is enabled 
l LED off = Page Warning Tone is disabled 
P.Press the HOLD button to save the entry, 
Confkmation tone is...

iqfirzite DVX’and DVX” 
SYtSTEBB P-RS PROG-G D@itaI Key ‘relcphone systems 
SYSTEM FEATURES (ConVd) 
G. LCR Enable 
Prop- Steps 
If this feature is to be assigned: 
1. Press the LCR ENABLE flexible button 
(Button #7). This feature will toggle on and 
off with each depression, and the display 
wrll update with each depression. 
l LED on = LCR is enabled 
l LED off = LCR is disabled 
2. Press the HOLD button to save the entry. 
Conhnation tone is heard. Description 
If Least Cost Routing is to be used, it...

r 
irlfintte DVX’ and DVX’ 
Di@d Eey Telephone Systems 
SYSTEM PARAMETERS PROG-G 
I. 
Group Listening 
Programmhg Steps 
If Group Listening is to be assigned: 
1. Press the GROUP 
IB’IENING flexible but- 
ton (Button #9]. This feature win toggle on 
and off with each depression, and the dis- 
play will update with each depression. 
6 LED on = Group List&g is enabled 
l LED off = Group Listening is disabled 
2.Prer.s the HOLD button to save the entry. 
Conknation tone is heard. Desctiption 
All digital...

r 
SYSTEM PmRS PROGRAMMING D&itaI Key Telephone Systems 
E, call Cost Display Feature 
Prog~ steps 
If Call Cost Display Feature is to be enabled: 
1 .Press the CALL COST DISPLAY flexible 
button (Button # 11). This feature will tog- 
gle on and off with each depression, and 
the display will update with each depres- 
sion. 
. LEDon= 
Call Cost Display is enabled 
l LED off = Call Cost Display is disabled 
2. Press the HOLD button to save the e&y. 
Confirmation tone is heard. 
L. Music On Hold 
If Music...

r 
f@&e Dvlt’andDVX” 
Digital Key Telephone Systems SYSTEM PJ%RAmmERS PROG~G 
710.3 A’ITENDAIUT STATION ASSIGN- 
BUENT 
Prog~ Steps 
If Attendant Station(s) are to be changed: 
a.Press FLASH and dial [lo]. The following 
message is shown on the display phone: 
b. Enter up to three three-digit station num- 
ber(s) 
on the dial pad. 
c. Press the HOJD button to save the entry. 
Confirmation 
tone is heard and the display 
will now update. 
710.4 SYSTEM TTUHEAND DATE 
To 
set the time and date which appears...

SYSTEM P ARAzldETERS PROGRAMlvIlNG iqfirzite DVX’ 
and DVX” 
DigItal Xey Telephone Spatems 
MISC. SYSTEM PARAnuEm Rs (cont’d) 
710.5 PBX DIALING CODES 
Programming Steps 
If PBX Dialing Codes are to be assigned: 
a. Press FLASH and dial 112). The following 
message is shown on the display phone: 
I PBK DW cm 
i #I#, ##, ##, ##, ## 
b.Enter five twodigit code numbers, one 
right after the other, on the dial pad up to 
a maximum of ten digits. 
c. Press the HOLD button to save the entry. 
Confirmation tone...

r 
irtfinite DVX’tiDVX’ 
Dig&al Xey Telephone Systems 
SYSTEM PARAMETERS PRGGRLWMING 
MISC. SYSTEM PARAMETE 
RS (Co&d] 
710.7 REUW/SENSOR PROGRAMMING 
Programrniqq Steps 
If Relays are to be assigned: 
a-Press FLASH and dial 1141. Relay #l (Flex 
Button # I) and On-Board Relays (FlexBut- 
ton #ll] LEDs ti be lit indicating the 
system Is in the pro&ramming mode for 
“On-Board” relay prom The fol- 
lowhg message is shown on tde display 
phone: 
To program “On-Board” relays: 
a. Press the “On-Board” Relays...

r 
irLfini.k DVX I and DVX I1 
SYSTEM PARAMETERS PROGRAMMING D&it.& Kcy Tckphone Syi~tems 
RELAY/SENSOR PRoGRAMMIlV G (Cont’d) 
A Pr&dl relay for External 
: 
Prog * ASteps 
1. Press the flex button that corresponds to 
the desired relay to be programmed. 
Z&Dial 111 on the dial pad, 
3. Enter a one-digit page zone number (l-4) 
4. Ress the HOLD button to save the entry. 
Confkmation tone is heard and the display 
will now update. 
Wbm: 
- X= Page Zones lthnl4 
B. Pl-o*amming relay for RAN sm: 
Rog~...

r 
Prog * g steps 
1. Press the flex button that corresponds to 
the desired relay to be programmed. 
2. Dial 131 on the dial pad. 
3. Press the HOLD button to save the entry. 
Confirmation tone is heard and the display 
will now update. 
!  D&kid Hey Telephone Systems 
SYSTEM PARAMETERS PROGRAMMING 
RELAY/SENSOR PROGWWJkltN G (Cont’d) 
c- LY relay for Power Failure 
: 
Description 
POWER FAILURE TRANSFER: When the in@ 
nite Power Failure Transfer Unit is used for 
Power Failure, It provides the relay...