Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

@fir&e DVX I and DVX’ 
~&&al Key Telephone Systcmts 
< 
Tnmmil Dam 
2 
> Rabivscma 
> 3 
> CT.5 (ChuulvSend) 
5 
 0s.R (Data se! RMdy) 
6 
< 
GND > 7 
DTR tDam?enninal Rsadyj 20 DTR mm Wz;z 
‘8” ~ckam h-cm the 
RS-232C PINQUT 
Data Communication R~uirwnent6 are: 
A) seri8l Port Compatible 
6) ASCII coda compatible 
C)8Data~BltsandlStopB11 
3 RZ%trol Melhod: xon/xoff 
NOTE Arrows show flow control direction SIrrNla) ’ l 
Rs-422 PlNwT 
DaU Communkation Flequiremanta are: 
A) setid port compa!w 
B) ASCII...

r 
INSTALLATION iqfhite DVX’tmdDV2K” 
DigitalEeyTelephone8ystems 
. 
Pin I1 Ioranaal 
Jy; Pin #2 (blue) 
Pin #3 (black) 
Pin M (red) 
tin #a {brown) 
cKs{clurtu&cq 
’ 5 6 
A) SerfsI Porn Compatible 
5) ASCII code compalti 
C)8DataSf!sand1StcpBH 
8 I!EZZLA Mehd: iadx0n 
NOTE: Amws show ffow oomrd direction. 
* ff mqulred by tha prfnter or t6fr~inal 
3 ----- .- Pin fll (blue) 
Pin #2 (bkick) 
Pin #3 (tad) 
- Pin 114 (grew) 
g ----- 
Pii x5 (yellow) pilnrfs (white) 
2 (bWJ Tmrumtl dpm {-) 
> . . 
4 wd <...

r 
INSTALLATiON 
RS-23% Cmnttctor 
or M Wute Comxtor(5~ 
-fo~DFor D&n 
- I=.*~~ 
-. 
C. 12QO Band Modem Module (MM) 
This optional 1200 baud modem can be 
installed on either the DVX ’ or the DVX JJ 
systems to add the capability of communi- 
cating with the system from a remote site 
or location at the rate of 1200 baud. Both 
systems provide as standard an on-board 
modem capable of transmi tting data at 300 
baud. With this module installed a trans- 
mission baud rate of 1200 baud can be 
selected....

r 
INST:AI;[LATION 
irzfirrite DVX ’ and DVX’ 
DigItal Key 
Telephone Systems 
mum of 13 DTMF Receivers can be in- 
stalled in the DVX ’ system. depending on 
whether the DTMF Receiver Module or the 
Dual IYTMFjTalk-Back Page Module is in- 
Genera@. one receiver will support DISA 
and/or 8 SLT stations 
under light to mod- 
erate traffic, K SLT and or DISA traf& is 
heavy, addiffoional DTMF receivers should 
be 
added. It is also recommended to add 
additional DTMF Receivers when a Voice 
MafI or Auto...

@finite DVX ’ and D’VX * 
D&r&d Key Telephone Systems INSTALLATION 
hmalling 
the DIMF Receiver Module onto the 
4x8 SLT Interface Board (CSBl: 
1. Locate the Jl connector on the 4x8 SLT 
Interface Board 
(CSB) and the Pl connec- 
tor on the M’MF Receiver Module. Refer to 
Figure 500-15 4x8 SLT Interface Board 
(CSB). 
Z-Take the DTMF Receiver Module and push 
the Pl pin connector gently onto the Jl 
pins on the 4x8 SLT Interface Board (CSB). 
3. Secure the DTMF Receiver Modulewith the 
screws provided...

r 
XNSTALLATlON iqfinite DVX’ and DV2C’ 
Digital Key Telephone Systems 
/f ----_-----.-----__-- * ---__--__ 
I_____ ___. -__-__. 
,-__.--____-__-_*________ 
-822 
q ..;: .: 
wm .’ .I 
RS-422 
Moclule  

i&.&e mxl and Dvx” 
Digital Key Telephone Symtema 
. . . 
INST~TION 
I” 0 I -._. I 
-.__ 
. .._. 
:‘-.... 
: l., 
3. ; 
i .lC “...;.-....--....-., 
.-.. 
--. 
-_ 
--.__ i . . . 
G.. =_, : 1 ; . ..i 
! Ii=!1  _ .__.__._ :y.: 
I Ii 
0 
hsue 1. Januarg 1993 
50043  

INSTAUATZON iq#inite DVX’ and DVX I1 
b&&al Key Telephone Spsttms 
500.7 DIGITS TERMINALS 
A. Digital Terminal Installation: 
The Digital Terminals are interfaced with 
the DVX ’ Basic KSU or Expansion KSU 
main key service board which provides 
eight circuits. E&ch of the e@ht clrctits are 
interfaced from the Jll connector on the 
Basic KSU or Expansion KSU maIn key 
service board to the MIX?. The digitaI ter- 
minals are interfaced witi the DVX II 4x8 
Key Interface Board (CKB) and 4x8 SLT 
Interface...

irlfinite DVX’ EUXI DVX” 
D&$d Iby Telephone 
s~8tCIIlB INSTALLATION 
Key Telephone Wtring 
DBSIDLB Console Wiring  BK YL 
GREEN 
XMTTIP 
RED 
XMT RING 
Single Line Telephone Wiring 
Figure 600-20 Digital Terminal Modular Block Wiring  

INST&LATION iqfinite DVX’andDVX” 
D&&al Key Telephone Eqstems 
bracket. 
2.Ltie 
up the hooks at the bottom of the 
bracket so that they engage with the slots 
cut in the bottom of the telephone base. Tilt 
the telephone back and lock the telephone 
into the hooks at the top of the bracket. The 
bracket wiIl snap in place. 
3. Route the line cord from the wall jack and 
plug into the connector on the back of the 
telephone. Now match the two key hole 
slots on the base plate with the lugs on the 
630-A...