Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

imite DVX’ and DVX’ 
Dj@m gcS TCrephone 
SJ?StCIWi SYSTEM PAEWWXERS PROGRAMMING 
RELAY/SENSOR PROG RtlMMING (Cont’d) 
E. f’rogramming rck~y for co tie 
COlltIOk 
From steps 
I. press the flex button that corresponds to 
the desired relay to be programmed. 
2.Dial [5J on the dial pad. 
3. Enter a two-digit CO Line number (0 l-28) 
4. Press the I-lOLD button to save the entry. 
ConfIIation tone is heard and the display 
will now update. 
ON BBNBU BElAY 
i BEMY l=WJIEfl( 
- xX= CO Line number 
P. Aes&n...

r 
SYSTEM PARAMETERS PROG-G infinite DVX’ and DVXn 
DigftaI Key Telephone Systems 
R~,~AY/SENSOR PRO0 RAMMING (Ccmt’d] 
G. Ptogramsensingch’cuitasa~ 
Sensiu.~$ (RAN END) circuit: 
grammhg Steps 
a. MaJ I61 on the dial pad. 
b. Enter a one-digit RAN Table number [ 1-8) 
the sensing circuit should be associated to. 
c. Press the HOLD button to save the entry. 
Confirmation tone is heard and the display 
d now update. 
- X= RAN Table number Description 
RAN SENSING [RAN END): The Recorded An- 
nouncement...

If Baud Rate[sI are to be assigned: 
1. Press FLASH and dial [15]. The ftrst button 
will be iit and ready for programming Port 
# 1. The following message is shown on the 
display phone: Description 
The infinite Digital (DVX) Key Telephone Sys- 
tems can provide outputs such as SMDR or 
ICLID to either the standard RS-232C ‘On- 
Board” connector on the DVX I BKSU or CPB 
board or to the optional RS-232Cj422 I/O Ex- 
pander Module connector(s). When features 
such as SMDR or ICWD are desired, the Baud...

msc. SYSTEM P AEWMETERS (Cont’d) 
710.8 ACCESS CODES 
Prm Steps 
If the system is in the programnUng mode, 
continue using program codes. if starting to 
progkun here, enter the programming mode. 
Refer to Sec. 700.2. Program Mode En&-y lKey 
Station). 
If Access Codes are to be changed: 
1. Press FLASH and dial [ZO]. The following 
message is shown on the display phone: hone Systems 
Description 
Tbis section describes the procedures and 
steps necessary to program Access codes. 
The buttons on the...

@j+tite DVX’andDvX1l 
Digital Key Telephone Systems SYSTEM P- PROGRAMMING 
ACC- CODE PROG- G [Cont’d) 
B. Database Admin. Password 
Programming steps Description 
If this feature is to be assigned: 
1. Press the ADMIN 
PASSWORD flexible but- 
ton [Button #2). The following message is 
1 
shown on the display phone: - 
DYIIIPAmaBD 
8226 
- The 
password used to enter customer database 
programmiq can be individualized 
by each 
customer. This allows tbe system administrator 
to block unauthorized...

r 
~PARtUWlXRSPROGIUMMiNG infinite DVX’ and DVX’ Digital Key Tcieplxone Systems 
MISC. SYSTEM PARAB6ETERG (Cont’d) 
710.10 STATION MESSAGE DETAIL RE- 
CORDING 
(SMDR) 
Progiznmig Steps 
If Station Message Detail Recording is to be 
used: 
1. Press FLASH and dial (2 11. The following 
message is shown on the display phone: 
::I 
2.To program SMDR features, use the flex- 
able button(s) as defiied in- the following 
procedures. 
3.The 
SMDR TYPE. and PRINT features will 
t@e on and offwitb eachdepression,...

r 
SYSTTEM PARAMETERS PROGRAMMING 
STA’I’XON MESSAOE DETAIL RECORDmG 
[Cont’d) 
C. Character Print Assignment 
Programmiq Steps Description 
1. Press PRINT FORMAT flexible button (But- 
ton #3) to determine the print format of 
SMDR records. This feature wit1 toggle on 
and off with each depression. and the dis- 
play will update with each depression. 
l LED ON = 8O-Character is enabled The system can be prograrmned to prtnt indi- 
vidual SMDRrecords in either a l-line 8Gchar- 
acter format or a 3-line...

r 
GYSTEILZ P ARAMETERS PROGRAMBEING 
iqfinite DVX’ and DVX’ 
Digital Keg Telephone Systems 
MISC. SYSTEM PARAMETE RS (Co&d) 
710.11 WEEKLY NIGFM’ MODE SCHED- 
F steps 
If entries or changes need to be made to this 
schedule: 
a. Press FLASH and dial [22]. The following 
message will then be shown on the display: 
A. Automatic/lYIanual Operation 
I3WmmWg Steps 
1. FWss the AUTO/MANUAL flexible button 
(Button #I 1). This feature wiU toggle on and 
off with each depression, and the display 
will update...

r 
i@dte DVX I and DVX’ 
J-&$&II Key Ttfephone Systems 
b!nsc. SYSTEM PARAMETE RS (Cunt’d) 
710.12 DIRECTORY DIALING 
Pro~amming Steps Description 
Enter. Change, Erase or to just View entries in 
the Directory Dialing list: 
1. Press FLASH and dial I23LThe following 
message will then be shown on the display; Directory dialing allows station users to obtain 
a directory of station users and have the system 
dial the extension that is currently on the dis- 
play. The infinite DVX ’ System provides loca-...