Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

r 
i@&te DVX’andDVX’ 
Dj#d Key Telephone Systems CUSTO- DATA EASE PROGRAMMING 
Table 700-l Default Values [Cont‘d) 
1 FEATURE 
! Select Page B 
New Station Range (#&I 
DIG-DATE IN~~~RFA~~EuNIT~DDIU) 
BaudFtate 
Character Length 
Stop Bit 
Flexible Port Assignment Feature - Stations 
Local Number/Name Translation Table 
I ICLID FEATURES: 
Enable/Disable 
Name in Display 
Baud Rate 
Pot-t # 
*ACD GRCXI-P PROGRAMMING: 
ACD Groups (l-8) 
Alternate ACD 
Group 
ovemowAssignment 
Announcement Table(s) Entries...

CUSTOMER DATA BASE PROC+RAhWIINCi [email protected] DVX’ and DVX” 
Mgital Key Telephone SJrstems 
Table 700-l Default Values (Cont’d) 
FEATURE 
Select Page B 
UCD TIMERS: 
Ring Timer 
MITmmer 
Over Flow Timer 
wrap-up Tirne.r 
, No-Answer Recall Timer 
No-Answer Retry Timer 
UCD RAN Am-rouncement Tables 
‘PC/ACD Event Trace 
Event Record 
Port # 
. VM GROUPPROGRAMMING: 
t VA4 Groups (l-8) 
AItcmate VM 
Group 
Leave Mail 
Table entry 
E i Retrieve Mail Table enny 
Station Assignments 
VM Leave/Retrieve Disconnect...

r 
irlfinite DVX’ and DVX’ 
D@ital Key Telephone Systems CUSTOMER DATA BASE F’ROGRAlHMlNG 
Takrle 700-l Default Values (Cont’d) 
FEATURE 
Insert/Delete TabIe 
Daily Start Time Table 
Week@ Schedule Table 
Route for 555-1212 
; INBMLJZE DATA BASE PARAMETERS: 
hit system Parameters 
hit CO Line Attributes 
Inft 
Station Atkibutes 
Init 
CO/Station Port Parameters 
Itit Exception Tables 
Init System Speed 
Inft I.ZR Tables 
hit Entire System and Reset 
Init ICIID Parameters 
Inft Directory Dfaling Tabfe...

irtfinite DVX I and DV’X I1 
CUSTOMER DATA BASE PROGRhMlKING D&Sal Key Telephone systems 
TO enter the program mode: 
a. Press ON/OFF button. (optional) LED 
lights and intercom dial tone is heard. 
b. On the dial pad, press the asterisk (*I 
twice. 
C. On the dial pad. enter the digits I3lI21[2lISI 
(DBAMJ’. Confh-rnation tone is heard. 
l ‘This is a default setting, however may be 
changed after entering programming. 
d. The ON/OFF button LED is lit. The system 
is ready to program. 
Other telephones...

infinite DVX ’ and DVX ’ 
digital Ety Telephone Systems 
CUSTOMER DATA EkASE PROG-G 
700.6 
CUSTOMER DATA WORKSBEETS 
Before any attempt at progmmming 
is made. it 
is strongly recommended that 
customer data 
worksheets be prepared (Refer to Appendix A). 
These worksheets should become part of the 
permanent record of customer progmmming. 
Refer to the following sections when preparing 
the worksheets. 
700.7 DATA BASE FIELDS 
The data fields are used to set system timers, 
determine central office line...

r 
CUSTOMER DATA BASE l’R0GRAMXING iqfinite DVX’andDVx” 
Wital Key Telephone Systems 
3. Press the iEmwl key on the PC. The followhxg 
display will be seen on the Personal Com- 
puter monitor. 
/ 
PMW PUSReady 
, 
1428 Digftnl Key-System Eng. Ucr. 2.8alS MTE: BBAJAZ IIIIE: 89:11:43 Mmi pr3ssuonD: 
 
4. Enter the password [VODAVIJ, and press 
the m key again. Proper entry of the 
password wiIl result in the ADM> prompt. 
Proceedwitbprogmmmingzf&ingtoF@- 
ure 7061 for terminal characters that 
represent...

iqfinite DVX’andDVX” 
DIgital Eey Telephone Sy~tCrn~ 
CUSTOIHD~ DATA BASE PROG-G 
29. I SYSTEM SPEED BIN 1 
; 
30. 1 STA-SPEED-BIN (station 100 thru ’ 
I 
I 155) 
1 31. 1 SPEED-DIR (directory entrv) 
i 32. 1 ICLID_TRANS_TABLE (trans table 1 
1 r entrv) 
I 33. i ICLID 7JAC TABLE (uac table entrY) 
134. i SPECIAL TABLE 
I 35. i PORT TO STATION 
i 36. t POKF l-0 co LINE 
i 37. 1 STATUS FUZQUEST 
38. 1 END~OFJ’ILE 
Forward and backward compatibility will be 
maintamed, If the fiIe being uploaded from the 
PC...

r 
&jWfe DVX’andDVXn 
[email protected] Key Telephone 
Systems SYSTEM PARABEXERS PRCIGRABBMING 
SECTION 710 
SYSTEM PARAME TERS PROGRAMMING 
Profgamdng steps Description 
If the system is in the programming mode, 
continue using the program codes. Ifstarting to 
program here, 
enter the programming mode. 
Refer to Sec. 700.2 , Fk-ogram Mode Entry (Key 
Station). 
If any System Tpmers are to be changed: 
l.I?t-ess FLASH and dial [Ol]. The following 
message is shown on tie display phone: This section describes the...

r 
in@nite DVX’ and DVX u 
D@itaI Key Telephone Systems 
SYSTEM TIMERS (Cont’d) 
A System Hold Recall Timer 
RotTanning Steps 
If this timer is to be changed: 
1. Press the SYSI’EM HOLD RECALL TIMER 
flexible button (Button #I). The following 
message is shown on the display phone: 
2. Enter a three-digit timer value on tile dial 
pad which corresponds to 001-300 sec- 
onds. 
3. Press the HOLD button to save the entry. 
Confirmation tone is heard and the display 
will now update. 
B. Erclusive Hold...

irifinrte VVX’andDVXn 
mtal I.&y Telephone Systems SYSTEM PARAMEXERS PROGRAMMING 
SYSTEM TIMERS [Cont’d) 
C. Attendant Recall Timer 
Progr-g steps Description 
If tMs timer is to be changed: 
I. Press the ATTENDANT RECALL TIMER 
flexible button (But-ton #3). The following 
message is shown on the display phone: This timer determines the amount of time a 
recalling calJ will ring at the attendant station(s) 
before the system will release the hne. 
When a CO Line recalls to the Attendant station...