Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

imite DVX’ and DVX’ 
Ecy Telephone Systems KNSTALUCI’ION 
I 
‘2 
c’l Pin #1 (orange) 
Pin #2 (blue) 
Pin #3 (black) 
1 Pin #4 (red) 
I 
I 
1 Pin #5 (green) 
Pin #6 (yellow) 
1 
Pin #7 (white) 
Pin #8 (brown) 
- 
CPB l/O 8 Pin Modular Jack Pinout 
8 PI Mod Jack 
6 (yellow) Transmit Data 
5 (w=n) Receive Data 
RTS (Request to Send) 
I CTS (Clear to Send1  I 
7 (white) DSR (Data Set Ready) 
3 (black) DTR (Data Terminal Ready) 
DTR must be held high or data from the 
KSU will stop 
RS-232C PI NOUT 
Data...

another slot. One Central Processing 
Board is required per system, 
ids & Indicators: 
?kro green LEDs located along the iiont 
edge of the Centrat Processing Board (CPB) 
provide an indication of the presence of 
+5V dc & -5V dc to the PCB. A third red 
LED located just below the two greem LEDs 
provides a system ‘heart beat” indication. 
Modem Intcsfkce: 
The Central Processor Board (CPB) con- 
tains au on-board modem that is capable 
of transmitting data at a rate of 300 baud. 
The modem supports and...

i@nite DVX’ and DVX’ 
Digital Key Telephone Systems INSTAILATION 
F 
-co1 -e 
.- CM --- a .:.. . . 
- co3 -.-. a. :. ‘:. 
---a 
- F-MAY -- a. 
StEllV5 
:: .: 
I. 
i : *... .‘.. ., ‘. 
: ,.: .:, : 
*-  :. 
1 I 
c Pin #l (blue) - N/C 
Pin #2 (black) - Ring 2 
I 
1 Pin #3 (red) - Ring 1 
1 Pin #4 (green) - Tip 1 
c 
I Pin #5 (yellow) - Tip 2 
I 
I 
Pin #6 (brown) - N/C 
RJ-14 Modular Jack Pinouts for 4x8 Key Interface Board (CKB) 
Figure 600-13 4x8 Rcy Intufacc Board K?EBl 
Issue 1. January 1993 
500-29  

INSTALLATION infinite DVX I and DVX’ 
D&&al Key Telephone 8yitems 
SEE DETAIL A 
PORT CARD 
TO MDF CABLE 
DETAIL A BOTTOM PLATE, 
FEED CABLE BEI-VVEEN 
SQUARE KNOCKOUTS 
AS SHOWN 
EXPOSEDhRAIDED 
PORTION OF CABLES 
IS TO BE GROUNDED 
BY CABLE TIE AS 
SHOWN 
Figure 600-14 Shielded Cable Ttrminatione  

The card also provides proper fusing or 
protection to comply with the requirements 
of UL 1459 Second Edition and CSA C22.2 
No. 225 standards. 
The 4x8 Key Interface Board also provides 
the interface for eight digital key teie- 
phones using two 64K channel arrange- 
ments. Stations connect to the board via 
the MDF through a 50-pin connector lo- 
cated on the front edge of the board. Each 
station connection requires four wires to 
connect 
to the board. 
A Digital DSS Console, a Single Line Tele-...

INSTALLATION iqf?nfte DVX’andDVXn 
Dig&al Key Telephone Systems 
for wiring information. 
Application Module(s) Connections: Table 500-S 4x8 Key Interface Board (CEB) 
The J 14 
connector on the 4x8 Key Interface 
Board (CKB) board allows the installation 
of one application module {i.e. DT’MF re- 
ceiver) to the system. Refer to Section 
500.6, Application Module(s) InstaJhtion 
for a description 
of the available applica- 
tion modules. 1 PAIR 1 PIN j COLOR ’ DESIG 
: 1 26 
WH/BL Port 01 Xmt Tip 
i 1...

i@nite DVX’ and DVX” 
D&WI Key Telephone Systems 
E. 4x8 SLT Interface Board (CSB] 
The 4x8 SLT Interface Board (CSB) is a four 
CO Line by eight single line telephone in- 
terface board. The card is a combination 
card that contains the necessary circtitry 
to connect four CO/Centrex/PBX loop 
start Ihes and eight standard on-premise 
single line telephones (2500 type) to the 
system. This card also contains one addi- 
tionaI voice (transmit) path for external 
paging and a connector for adding one...

XNSTAwcATfON in.ite Dd and DVX I1 
Digital Key Telephone Systems 
0 
I 
Station 
0 connect0 
Message 
Wait 
Circuitry 
,. . . . 
: ..::.. : 
:.. ,. 
. . . 
.: 
‘. 
:.. 
. ..:, ,. 
I 
. 
*‘. 
: ‘, : 
_. 
: 
., . . . 
:.:.. 
(FUTURE) 
Opfionaf 
Dual DTMFI 
Talk-Sack Page 
Module 
---JqE!F&---- 
Optional 
Single DTMF 
Receiver 
Module 
Pin #l {blue) - N/C 
Pin #2 (black) - Ring 2 
1 Pin #3 (red} - Ring 1 
1 Pin #4 (green) - Tip 1 
c, 
Pin #5 (yellow) - tip 2 
1 I 
Pin #6 (brown] - 
N/C 
4x8 SLT Interface...

iq,@ite DV2Cx& DVX’ 
DQ#al Xcy Telephone Systems INST2U.LAmON 
stations coIulection6: 
The station ports of the 4x8 SLT Interface 
Board (CSB) are wired to the main distri- 
bution iiame via a 25-pair. (50-pin) female 
amphenol type connector located on the 
tkont edge 
of the board, connector 53. A 
25-p& cabie with a 5O-pin male smphe- 
nol-type connector is required to extend 
the station ports to the maLn distribution 
frame. The pinouts are 
shown in Figure 
500-9 Basic KSU Equipment Cabinet....

r 
ZNSTALLYITON iq#.nite DVX’ 
and DVX’ 
D&ital Key Telephone Systems 
Application 
Module(s) Connections: 
The 514 connector on the 4x8 SLT Inter- 
face Board allows for the installation of one 
application module (i.e. Single D’i’MF re- 
cefver or the Dual DTMF/Talk-Back Page 
Module) to the system. Refer to Section 
500.6. Application Module(s) Installation 
for a description of the available applica- 
tion modules. 
500.6 APPLICATION 
MODULX(S) IN- 
STAUATION: 
k ~md/& Module QOM) for the 
The DVX ’...