Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

injkite DVX ’ and DVX I’ 
=mlYMON TABLES PROGRAMMING Digital Key Telephone Systems 
EXCEPTION TABIS+ FROGIUMBUING 
(Cont’d) 
Auow Table Pru@unming (Cont’d) 
Prog$xmmbg steps 
- 
XXX = Area code (must match AREA- 
X entry) 
- DDD = “Don’t Care” dfgit (three en- 
Mes, DND button) 
- {SI= Search Special Table Command 
(TRAM button) 
2. For an entq that fs to reference the Home 
Area Code table (specfal table 41 the entry 
may also be entered to expect or not expect 
a leading digit [I]. In fact fn some...

EXCEPTION TABLES I’ROG~G 
RxCEPTION TABLE-8 PROGWUDIING 
(Cont’d) 
c. Deny Table Programmiq! 
[email protected] Steps 
1. Press the DENY TABLE A or DENY TABLE 
B flexibfe button (Button #2 or #4). The 
following message is shown on the display 
phone: 
The first two bin locations are displayed. 
2.Enter the two-digit bin number (01-10) of 
the bin to be programmed. 
3.Ent.er the deny code: 
where: 
- 0 to 9, *, # = corresponding deny dig- 
its (numbers) 
- hRlTi3 = Don’t Care digit 
4. Press the HOLD button to...

EXCEPTION TAB- PROG-G 
, 
i@zite DVX’ and DVX” 
Digital Key Telephone Systems 
=CEPTfON TABU3S PROG-G 
(Cont’d) 
D. Special Table Programminq 
F?rog- steps Description 
To program a special table, it is first necessary 
to assign an area code to the table (except for 
the home area code). 
To assign an area code to a special table: 
1. Press the appropriate AREA CODE TABLE 
f 1-4) flexible button (button #9-l 1). The 
foliowing message is shown on the display 
phone: The special tables provide greater...

_ 
iqfmite DVX’ and DVX’ 
D&id Key Telephone Systems EXCEPTION TABtEs PROGRAMMING 
EXCEPTION TABLES PROGRAAlMlNG 
[Cont’dl 
E. Displfqing Toll Table Entries 
Programming Steps 
To display entries in either the Allow/Deny 
tables or the special tables: 
1. Press the DISPLAY TABLES flexible button 
button #12) while entering inform&ion 
into a table. 
2.WhiIe viewing entries made into an allow 
or deny table, two entries at a time will be 
displayed on the bottom line of the display. 
By pressing the...

irlfinite DVXrandDVXn 
mgital Key Telephone !3pttms LEAST COST RODTING &CR) ~OGRAIKMINE 
SECTION 765 
LEAST COST ROUTING (LCR) PROGRANLMlNG 
785.1 INTRODUCTION 
Least Cost Routing &CR) selects the most eco- 
nomical programmed route for an outgoing calI. 
when a station user dials an outside number, 
the LCR feature analyzes the number and then 
automatical@ chooses an outside line from the 
group that has been programmed as most eco- 
nomical. The LCR feature puts the responsibil- 
ity of choosing the...

&finite DVX1andDVXn 
ml” COST ROUTING &CR) PROGRAMMING Di@td lCey Telephone Systems 
me period route within the specified route 
table. ~ch of the 16 Route Tables contain four 
me sensitive routes. Routes are determined by 
the me of day and day of week as specified in 
the Daily Start T3me table and the Weekly 
Schedule table. 
After the appropriate route is selected, LCR 
Class of Service becomes applicable. A station 
can use only those line groups programmed 
with a priority number equal to or higher...

iqjinite DVX’andDVXn 
Digital 
Kq Telephone Systems 
IzLAsT COST ROUTING &CR) PROG~QIMMING 
LCR PROGRAMMING (Cont’d) 
765.2 LCRTABLE% PROGRAMMING 
PfDgr steps  a.rmag 
If the system is in the programming mode, 
continue using the program codes. Ifstarting to 
program here, enter the programming mode. 
Refer to Sec. 700.2. Program 
Mode Entry (Key 
Station). 
To program the system for Least Cost Routing: 
1. Press FLASH and dial [75]. The following 
message is shown on the display phone: 
2.There are...

LEAST COST ROUTING &CR) PROGRAWHING 
, iqjinite DVX’ apd DVX I1 
Digital Eey Telephone Syetwpe 
LCRPROG- G (Cont’d) 
A. s-Digit Area/Of&t Code Table 
gpimmhg Steps 
1. Press 3-DIGIT TABLE flexible button (But- 
ton # 11. The following message will be 
shown on the display phone: 
- L = 101 for non leading 1 [,l” not di- 
aled) 
I11 for leading l(“1” is dided) 
- NNN = area/office code 
- RR-routelistnumberU0-15 
- Y = [O) do not 
go to 6-Digit table 
[ 11 go to 6-Digit table 
- PP = number of digits...

i@ite DVX’ and DV?L’l 
Dj@tal Key Telephone systems LE.+ST COST ROUTING &CR) PROGRAMBEING 
1. Press the 6-DIGIT TABLE flexible button 
(F5utton # 21. The following message is 
shown on the display phone: 
Whm: 
- S = 101 to remwe codes 
[lltoaddcodes 
- Akw=areacode 
- RR=routenumberCMJ-15 
- NNN=officecode 
2. IVess the HOLD button to save the entry. 
Confirmation tone is heard and the display 
will now update. 
3.Enter additional of&e codes to be pro- 
grammed into the same Area Code/ Route 
Table,...

@finite DVX I and DVX ’ 
LEAST COST ROUTING &CR) PROGRANMING D&ital Key Telephone Systems 
L-CR PROG FtAMMlNG (Cont’d) 
c. exception Code Table 
Prog;ramminR steps 
1. Press EXCiFlION TABLES flexible button 
(Button #3). The following message will be 
shown on the display phone: 
Where: 
- S = IO] to remove code from table, 
[I] to add code to table 
- XX= exception codes for single 
[email protected] 
codes, 
press MUTE button as 2nd 
digit). 
The digits [+E] and I#] may be entered 
as valid digits. 
- RR= route...