Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

infinite DVX * and DVX I1 
m DATABASE PARAMETERS Dig&al Key Telephone 
Systems 
INIT. DATABASE P ARAbETERS (Cont’d] 
J. IniB Directory Dialing Table 
Parameters 
ProgImming 
steps 
If Directory DialingTable Parameters need to be 
initialized: 
1. Press the Directory Dialing Table Parame- 
ters flexible butto~~ (Button #lo). The fol- 
lowing message will be shown on the 
display phone: Description 
The Directory Dialing Table parameters may be 
initialized setting all data fields to their original....

i&.&e DVX ’ and DVX II 
~QltaI Key Telephone Systems m DATABASE PAWMETERS 
INIT. DATXBASE PARAMETE I@ (Co&d} 
K. Initinltzt Hunt Group Parameters 
Programming Steps 
If Group Parameters need to be inftiaked: 
1. Press the Hunt Group Parameters flexible 
button (EMton #1 1). The foIIowing mes- 
sage will be shown on the display phone: Description 
Hunt Group parameters may be jnitialized set- 
ting aII data fieIds to their originaL default 
values. 
2.To inftia&ze the 
Hunt Group parameters, 
press the...

iqf3tite DVX’andDVX I1 
m DATME P&RAMETERS D&itd Key Telephone Systems 
INIT. DATABASE PARAMETE Rs (Co&d) 
I,. Lpitialize ACD or UCD Grunp 
Paramctcrs 
Rogramminf Steps 
If ACD or UCD Group Parameters need to be 
initialized: 
1. Press the ACD or UCD Group Parameters 
flexible button (Button # 12). The following 
message will be shown on the display 
phone: Description 
ACD or UCD Group parameters may be initial- 
ized setting all data fields to their original, 
default values. 
2.To initialize the ACD...

ittfintie DVXTandDVX’ 
~&&al Key Telephone System6 
m. DATABASE P ARAMETERS (Cont’dl 
M. Idtialize VM Group Parameters 
Progl -ng steps 
ff VM Group Parameters need to be initialized: 
1. Press the VM Group Parameters flexible m DATABASE PARAMETERS 
Description 
VM Group parameters may be initialized se-g 
all data fields to their ori-. default values. 
button (Button #13). The following mes- 
sage will be shown on the display phone: 
;;I 
2.To initialize the VM Group parameters. 
press the HOLD button....

. 
METIAtlzE DATABASE PANMETERS fqfinite DVX ’ and DVX ’ 
D&&al Eey Telephone Systems 
m. DATABASE P ARAMETERS (Cont’d) 
N. SydCm lb~& 
gramdng Steps 
If the system needs to be reset but not initial- 
izd: 
l.FWss the FESE3 flexible button (Button 
#20]. The following message will be shown 
on the display phone: Description 
This feature provides a hard system reset from 
the keyset instead of the KSU. This is useful in 
cases where miscellaneous data errors have 
occurred and the system needs to be...

r 
i@nite DVX’andDVX’ 
DJ#t.al Key Telephone Systems PRINTING SYSTEM DATABASE PARAMETERS 
SECTION 775 
PRINTING SYSTEM DATABASE “AIUMETERS 
775.1 INTRODUCTION 
Programming Steps Description 
If the system is in the programming mode, This section describes the procedures and 
continue using the program codes. If starting to steps necessary to print Data Base Parameters 
program here, enter the programming mode. 
and various portions of the system. 
Refer to Sec. 700.2. Program Mode Entry (Key 
Station)....

m-G SYSTEM DATABASE PARMBTERS iqjinite DVX’ and DVX” 
D#tal IKeg Telephone Systems 
syrctem D~~&%uIc 
printouts [Co&d) 
k priptfng System Parameters 
Progw Steps 
If a printout of all System Parameters 
is desired: 
1. Press the SYSTEM PAR#I?3ERS fleldble 
button (Button # 1). The following message 
will be shown on the display phone: 
PllUnslls?AMM 
2.To print the system parameter database , 
presstheHOLD button. ThefoIlowingmes- 
sage wiU be shown on the 
ciispIay phone: 
lwlnNEm PAm. 
When the system...

r 
iqf&te DVX’ aPd DVX” 
DQ.$w Key Telephone Systems PBINTING SYSTEM DATABASE PARAMETERS 
1 SYSTEM PARAMETERS 
* Eng. Ver. 2.0~ 
; SYSTEM TIMERS 
i-- 
f SHR EHR ART XFR PFT CFN PT 
: 60 180 44 45 10 15 2 
CPT CFT PTO COT SRT MWT HFT 
i 180 10 15 8 20 0 10 
I 
 
110 HFD 30  CQT ACB 0 
SYSTEM FEATURES 
A0 SY ENFI EO PW 3GM LCR 
I? Y N YYY N 
AC GL S CC MH 
NNN NY 
ATTENDANT STATIONS 
100 ### ### 
DATE & TIME FORMAT 
MM/DD/YY, 12 HOURS 
PBX DIALING CODES 
#It ## ## #X ## 
?ZXECUTIVE/SECRF.TAFtY PAIRINGS 
3...

p~ml%VG SYSTEM DATABASE PARKMETERS 
iqjinite DVX1and~~” 
Digital Key Telephone Systems 
system DataBase Printouts 
(Co&d] 
B. Printing Co h Attributes 
Pro- steps 
If a printout of the Co 
Line AttrIbutes is desired: 
1. Press the CO LINE ATI’RIBUTES flexible 
button (Button #2). The following message 
will be shown on the display phone: 
;I 
2.To print the data for ALL CO Lines, press 
the HOLD button. To print CO Line data for 
a specified CO tine Range enter four digits 
to sped@ the CO Line range...

@jinife DVX’ and DVX” 
D&$m Ecy Telephone Systems 
PRINTING SYSTEM DATABASE PARAMETERS 
Co LINE ATTRIBUTES 
CO 05 
co 01 -- 
-- 
LINE 05 
LINE 01 
SIGNAL TYPE 
UNA CONF PRI 
DX?F CO Y Y Y SIGNAL TYPE UNA CONF 
PRI 
DTMF CO Y Y Y 
SUPV DISA 
FLTM GRP COS 
1  ; N N 
10 1 
SUPV DISA FLTM GRP COS 
N N 10 1 1 
i RING ASSIGNMENTS 
100B 
co 02 
; -- 
LINE 02 
RING ASSIGNMENTS 
lDOB 
CO 06 
-- 
LINE 06 
SIGNAL TYPE DNA CONF PRI 
DTMF CO Y Y Y 
SUPV 
DISA F’LTM GRP CDS 
N N 10 
1 1 
RING 
ASSIGNMENTS 
10OB 
co 03...