Vodavi Infinite 4096 Key Telephone System Installation And Maintenance Manual

CUSTOMER DATA BASE PROGRAMMING Infinite 4096 Hybrid Key Telephone System 
When using a 
data terminal (I/O device) to program the system. the following chart presents 
the data terminal characters that are equivalent to the keyset buttons. 
a&t>? 
FiEiYOTE ADtlIN KEY DEFINITIONS 
Keyset Terminal Keyset 
Terminal 
HOLD ENTEWCR 
FLEX 1 
FLQSH 
i FLEX 2 
0 FLEX 3 
: i FLEX 4 
FLEX 5 
3 3 FLEX 6 
z z 
FLEX 7 
FLEX 8 
6 6 FLEX 9 7 7 FLEX 10 
9” i FLEX 11 
FLEX 12 
10 10 FLEX 13 
11 11 FLEX l‘+ 
* 
l SPEED 
#...

Infinite 4096 Hybrid Key Telephone System 
CW3TOMER DATA BASE PROGRAMMING 
Figure 700-2 Iqjinite 4096 Default Button Mapping 
--I FLEX 
BUTTON 
FIELD 
--J 
Issue 1. January 1992 700-3  

CUSTOMER DATA BASE PROG-G btjinite 4096 Hybrfd Key Telephone System 
Table 700-l Default Valuts 
FExruRE 
System Hold Recall Timer 
Exclusive Hold Recall Timer 
Transfer Recall Timer 
Preset Forward Timer 
Pause Timer 
Call Park Timer 
Conference Timer 
MSG Wait Reminder Tone 
Paging Timeout Timer 
CO Ring Detect Timer 
Hold Preference 
Executive Override Warning Tone 
External Night Ring - LBCl 
Attendant Overrlde 
Attendant Station Assignment 
Loud Bell Control 
PBX Dfaling Codes 
Executive/Secretaq...

Infinite 4096 Hybrid Key Telephone System CUSTOMER DATA BASE PROGRAMMING 
Table 7CMSl Default Values (Co&d] 
FEATURE 
UCD Timers 
Ring Timer 
MSG Int. 
Over Flow Timer 
Wrap-Up Timer 
Announcement Table 
CalI Foxward No Answer Timer 
Voice Mail Groups 
Voice Mail Outpulsing Tables 
Voice Matl Disconnect Table 
Hunt Groups 
Weekly Night Mode Schedule 
Manual or Automatic 
Schedule Programming 
CO Line Programming 
lYIMF/Pulse 
CO/PBX 
UNA 
Loop Supervision 
DISA 
Flash Timer 
CO Line Group 
Line COS 
UCD...

CUSTOMER DATA EASE PROGRAMMING 
Inmite 4096 Hybrid Key Telephone System 
Table 700-l Default Values (Cont’a) 
FEATURE 
Call Forward Access 
Forced LCR 
LCR COS 
Conference Enable/Disable 
Statton Programming 
Station Type 
Station Class of Service 
Speakerphone Operation 
Group Pickup Assignment 
Paging Zone Assignment 
Preset Forward Assignment 
CO Line Group Access 
CO Line Button Assignment 
Automatic Privacy 
Exception Tables 
Allow Table 
A 
Deny Table A 
Allow Table B 
Deny Table B 
Special Table 1...

Injinite 4096 Hybrid Key Telephone System CUSTOMER DATA BASE PROGVG 
Using the Remote Admin Key Definitions follow 
the same steps and procedures to program the 
4096 when using a texminal (as outlined in the 
following sections) * 
700.3 PROGlUM MODE ENTRY Cgey Sta- 
tion) 
pn>grammir~ is performed at station 100 using 
either the Enhanced or Executive Key Tele- 
phone. Programming is always done at this 
station regardless of the class of service or 
which station has been assigned the atten- 
dant(s)....

Injinite 4096 Hybrid Key Telephone System 
!WSl’EM PARAMETERS PROGRAMMING 
SECTION 710 
SYSTEM PARAMET 
ERS PROGWiMMING 
710.1 SYSTEM HOLD RECAU#TIMER 
gg-ammirq! Steps 
lf this timer is to be changed: 
a FTes.s FLASH and dial [O 11. The following 
message Is shown on the display phone: 
b. Enter three digits on the dial pad. 
c. Press HOLD button. Display wl.ll now up- 
date. 
710.2 
EXCWSNE HOL9 RECALLTIMER 
R ’ g Steps 
lf this timer is to be changed: 
a. Press FLASH and dial [02]. The following...

SYSI-EM PARAMETERS PROGRAMMMG In&&e 4096 HybrSd Xey Telephone System 
System Parameters Programming (Cont’dl 
710.3 TRANSFER RECAUTIMER 
Prognmming Steps 
If this timer is to be changed: 
a. Press FLASH and dial [03]. ‘Ihe following 
message is shown on the display phone: 
b. Enter three digits on the dial pad. 
c. Press HOLD button Display will now up- 
date. 
710.4 PRESET FORWARD TlMER 
Prognmming Steps 
If this tfmer is to be changed: 
a. Press FLASH and dial [041. The following 
message is shown on...

Infinite 4096 Hybrid Key Telephone System SYSTEM P 
AlUMETER6 PROGRAMMTNG 
System Parameters Programming (Cont’d.) 
710.5 
PAUSE TIhZER 
gramming Steps 
If this timer is to be changed: 
a Press FIASH and dial 1051. The following 
message is shown on the display phone: 
Description 
Determines the length of the pause when pro- 
grammed for use with speed dialing and LCR 
insert Tables. 
Default: Default is 2 seconds and is vartable 
from 1 to 9 seconds. There is no 0 entry. 
b. Enter one digit on the dial...

SYSTEM PARAMETERS PROGRAMMING Infinite 4096 Hytrrid Key Telephone System 
System Parameters Programming 0nt’dl 
710.7 CONFERENCE TIMER 
gmmming Steps 
If this timer is to be changed: 
a. Press FLASH and dial [07l. The following 
message is shown on the display phone: 
b. Enter two digits on the dial pad. 
c. Press HOLD button. Display will now up- 
date. 
710.8 MESSACE WAIT REMINDER TONE 
Programmhw Steps 
If this feature is to be changed: 
a Press FLASH and dial (081. The followlng 
message is shown on...