Vodavi Infinite 4096 Key Telephone System Installation And Maintenance Manual

Infinite 4096 Hybrid Key Telephone Spstem CO LINE ATTRIBUTES PROGRAMMING 
SECTION 720 
CO LINE ATTRIBUTES PROGWiMMING 
720.1 CO LJNE PROGRAMMING 
Programming Steps 
If the system is in the programming mode, 
continue using program codes. If starting to 
program here, enter the programming mode. 
Defer to Paragraph 700.21. 
If any CO line features are 
to be changed: 
a. Press FLASH and dial [40]. The following 
meSSage is shown on the display phone: 
b. 
C. 
Program button 12 (SLCTj will be lit. En- 
ter...

Co LINE ATTRIBm PROGRAMMING Infiite 4096 Hybrid Key Telephone System 
COUNEPROGRAMbUN G (Cont’dl 
A. MMF/Dial Pulse Pro@-m-W 
Progmmmirg Steps 
1. Press the DTMF flexible button (Button 
#l). 
l LED on = DTMF enabled 
l LED off= Dial Pulse enabled 
2. Press the HOLD button to enter data Description 
DTBdF. Each mdMdual outside line can be 
programmed to be either DlMF (tone) or dial 
pulse. When a line fs assigned as dial pulse, 
you can program the break/ make natlo and 
dhl speed. 
Default By default,...

Infinite 4096 Hybrid Key Telephone System CO LINE ATTRIBUTES PROCIU~WING 
co 
D. 
1. 
2. 
3. LINE PROGRWMR’I G (Coda) 
Loop supervision PmgraxMling 
Prognmmhg Steps 
Press the SUPV flexible button (Button 
#4). 
Enter a one-digit timer value on the dial 
pad between 1 and 9 which corresponds 
to 100-900 msec. 
Press the HOLD button to enter data 
E. DEW Pro@amming 
Rogpxnmbg Steps 
1. Press the DISA flexible button (Button #5). 
l LED on = CO lines set for DISA 
0 LED off= DISA is disabled 
2. Enter a...

CO LINE ATTRlBUI’E8 PROGRAMMING InJ?.nite 4096 Hybrid Key Telephone System 
CO LINE PROGRAMMIN G (Cont’dl 
F. Flash Timer Fqramming 
Programmiq Steps 
1. Press the FLASH flexible button (Button 
#6). 
2. Enter a two-digit ttmer value between Ol- 
20 which corresponds to lOOmsec-2 sec- 
onds. 
3. Press the HOLD button to enter data 
G. Line Group Programming 
Programming Steps 
1. Press the GROUP flexible button (Button 
m. 
2. Enter a one-digit value between l-8 which 
corresponds to Groups 1-8. 
3....

Injinite 4096 Hy?Md Key Telephone System CO LINE A’ZTRIBUTES PROGRWIKING 
CO LINE PROGRAMMIX G 
(Cont’dl 
H. class of Service (COS) Programming 
Progr’amming Steps 
1. Press the COS flexible button (Button #8). 
2. Enter a one-digit value between 1-5 which 
corresponds to five possible class of sew- 
ice to which a line may be assigned: 
COSl= No restrictions. 
COS2= Table 
A governs. Station COS 2 and 
4 are monitored. 
COS3= Table B governs, Station COS 3 and 
4 are monitored. 
COS4= Restricts O,l,*,#...

CO LINE PROGRAMMIN G (Cont’cl) 
I. 
CO Line Rlnglng Assignment 
Pro@ . g Steps 
Each CO line in the system may be assigned 
initial incoming ringing to one of the following 
destinations: 
l one or more stations (ke$set or SL?1 
l to a UCD. Voice Mail or Hunt Group 
l m-Net (via speed dfal) 
1. Press the RING ASSIGN flexible button 
(Button #9) to toggle to the RfngingAsslgn- 
ment display. ‘Ihe display will show the 
following informat.ioIlz 
Emi- 
l CO Ringing Assignments 
2 Display CO Ringing...

In,ite 4096 Hybrid Key Telephone System 
CO UNE ATTRIBUTES PROGRAMMING 
CO LINE PROGRAMMIN G (Cont’d.) 
CO Line Rlnghg Assignments (Cont’d) 
Pro.gramming Steps 
2. Press the RING fkdble button (Button #l) 
to program ring assignments. The follow- 
ing information will be shown: 
3. Enter the 3-dfgft destination (DDD) and 
the single digIt ring type 0 followed by the 
HOLD button. 
Valid: 
020-099 = System Speed Bins 20-99. for off-net 
ringing* 
IOO- 195 = Statton extension Numbers 
590-597 = Hunt Groups...

CO LINE ATTRIBUTES PROGIUMMING 
Infinite 4096 Hybrid Key Telephone System 
CO LINE PROGRAMMIN G (Cont’dl 
J. Conference Enable/Disable (Per Co 
LJm) 
Programmhg Steps 
To program Conference Enable/Disable: 
1. Press the CONF flexible button Button 
#13). 
l 
LED on = Conference is enabled 
l LED off = Conference is disabled 
2. Press HOLD button. Display will now up- 
date. 
K. Automatic Privacy 
Programmbg Steps 
To program Automatic Privacy: 
1. Press the PRIV flexible button. (Button 
#14). 
@ LED on...

Infinite 4096 Hybrid Key Telephone System STATION ATTRJBUTES PROGRAMMING 
SECTION 730 
STATION ATTRIBUTES PROGWWIBDNG 
730.1 STATION PROGRAMMING 
Programming Steps 
If the system is in the programming mode, 
continue using program codes. If starting to 
program here. enter the programming mode 
fYirst (Kefer to Paragraph 700.21. 
If station features are to be changed: 
a. Press FLASH and dial [501. The following 
message is shown on the display phone: 
b. 
C. 
d. Program button twelve (SW will be lit....

STATION PROG RAMMING (Cont’dl 
k 
1. 
2. 
PagingAccess 
Prom Steps 
Press the PAGE flexible button (Page k 
Button #l). 
l LED on = Paging is allowed 
l LED off= Paging is dented 
Press the HOLD button to enter data. Dcscrlption 
PACE. StaUon.s can ixlivldually be allowed or 
denied the ability to make pages. This applies 
to all internal and external zone paging. A 
station denied access to paging may sUll an- 
swer a meet-me page announcement. (Station COS 6 will not deny a station the abillty to 
make...