Vodavi Infinite 4096 Key Telephone System Installation And Maintenance Manual

Injinite 4096 Hybrid Key Telephone System INSTAUATION 
CO RAN Conneaions 
cwtomec Rovided 
Talk Battery 
24V DC 
COB 
‘OWER FAILURE TRANSFER 
I 
BFg* 
-----B-e 
LBC Terminak GROUND START APPLICATIONS on Basic KSU 
SIB 
TIP 
RING SLT RAN Cormec3ons 
MDF 
-- 
-- 
LOOP START APPLICATIONS 
Figure 500-18 CO and SLT RAN Connections 
RAN 
DEVICE 
Issue 1, January 1992 500-27  

INSTALLATION Infinite 4096 Hybrid Key Telephone System 
be configured for ring trip operation (loop 
start). The 9GV ac voltage sent to the SLT port 
wilI be recognized by the RAN device which will 
then answer the call. Refer to Figure 500-18. 
500.22 INSTALLING THE SINGlX LINE 
TELEPHONE D’IMFRS UNlT (SW 
The two DTMF receivers and two IYlMF sen- 
ders located on the APL board are sticient to 
support up to 16 Single IJne Telephones under 
moderate SLT usage. If more than 16 SLTs are 
instalIed, or SLT...

In,ite 4096 Hybrid Key Telephone System 
INSTALLATION 
RSM Module Switch SetUngs 
Switch Settings 1 
O=ON; X=OFF 
Equipment Needed: 
1 Phillips Screwdriver 
Two screws with washers are used to mount the RSM Module to the 
Applications Board (APL). 
Figure 500-19 RSM Baud Rate Selection 
Issue 1, January 1992 500-29  

INSTALLATION Irlfinite 4096 Hybrid Key Telephone System 
KSU PRINTER 
WE) TERMINAL 
Pin # 
2 
3 
4 
5 
6 
7 
20 / Transmit Data / 
 
 
Receive Data 
 
RTS (Request to Send) 
CTS (Clear to Send) 
 DSR (Data Set Ready) 
 
GND 
DTR (Data Terminal Ready) 
RS-232C PINOUT 
Data Communication Requirements are: 
A) Serial Port Compatible 
8) ASCII Code Compatible 
C) 8 Data Bits and 1 Stop Bit 
D) No Parity 
Figure5OG20RS-232CCmnections 
Pin # 
2 
3 
4 
5 
6 
7 
20 
500-30 
Issue 1, January 1992  

Infinite 4096 Hybrid Key Telephone System 
a. Refer to Paragraph 500.4 - KSU Installa- 
tion. The Expansion KSU mounts directly 
to the right of the Basic KSU. Refer to 
Figure 500- 1. Using the template pro- 
vided, identify the screw hole locations. 
Insert the two screws into the wooden 
backboard and tighten enough to hold the 
weight of the unit. 
b. Remove the connector cover on the right 
side of the Basic KSU. Refer to Figure 
500-3. Remove the last three cards on the 
right side of the Basic...

Table 600-8 SMDR Printout 
The SMDR feature provides detailed records of ail outgoing and/or incoming. long distance only 
or all calls exceeding 30 seconds. ‘This feature is enabled 
or disabled in system programming. 
By default. SMDR is not enabled and is set to record long distance calls only. A printout format 
of 80 characters maximum or 29 character maximum may be selected in system programming. 
The standard format is 69 characters 
on a single Une. A 29 character format will generate 3 Unes 
per...

Injinite 4096 Hybrid Key Telephone System IlWTALIATION 
I/ I 
II;----- 
BASIC 
KSU 
MUUN I INti -.__ -.- -- _ BRACKET% 
RIBBON CABLES 
FROM 8ASIC KSU 
CABLE 1 MOUNTING 
’ BRACKETS 
1 RIBBON CABLES 
TO EX;t;SlON 
I 
POWER 
CABLE 
EXPANSION 
KSU 
Figure 600-21 Installing the Expansion KSU 
Issue 1, January 1992 500-33  

Inmite 4096 Hybrid Key Telephone System SYSTEM CHECKOUT 
SECTION 600 
SYSTEM CHECKOUT 
600.1 INTRODUCTION 
Prior to actual power up and initia&atton. the 
Key System should be checked over to avoid 
start up delays or improper loading. 
A step-by- 
step checklist is provided for this purpose. 
600.2 PRELXLNARY PROCEDURE8 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
Verify that the DC output power cord fi-om 
the EPS housing is plugged into the DC 
connector on the BKSU. 
Make sure that the BKSU and EPS are...

SYsmM CHECKOUT Infinite 4096 HJrbrid Key Telephone System 
wte 4096 Power Supply Tests 
DC/DC CONVEHTER* 
VOLTAGE VOLTAGE 
DESIGNATION READING TEST’ POINT LOCATION 
REMARKS 
+5 WC +5 WC fl% Front of DC/DC Converter Adjustable on front cover 
of DC/DC Converter 
Front of DC/DC Converter 
‘The DC/DC Converter is pre-set at the time of manufacturing. but should be checked 
at system intttalizatlon with a digital volt meter having an accuracy of U%. 
VOLTAGE 
DESIGNATION 
117VAC 
+24 WC POWER SUPPLY 
VOLTAGE...

Infinite 4096 Hybrid Key Telephone System 
CUSTOMER DATA BASE PROGRAMMING 
SECTION700 
CUSTOMERDATABASEPROG-G 
700.1 IN’IXODUCTION 
The In$nf& 4096 Key Telephone System can be 
programmed to meet each customer’s inditid- 
ual needs. All programming is done at statton 
100 using the Enhanced or Executive model 
Key Telephone as the programming instru- 
ment. The Executtve model is suggested since 
the display is designed to assist in program- 
mQ-Q?- 
When the program mode is entered, the Key 
Telephone...