Vodavi Infinite 4096 Key Telephone System Installation And Maintenance Manual

Inmite 4096 Hybrid Key Telephone System 
RWTiILLATION 
Table 5CG5 Station Connectig Block (SLT) 
1 PAIR i PIN I COLOR / DESIG i DESCRF 
1 26 WH/BL VT 100 
1 BL/WH VR 100 
2 27 WH/OR - 
2 
OR,‘WH - 
3 28 WH/GN - 
3 GN/WH - 
4 29 WH/BN VT 101 
4 
BN/WH VRlOl 
5 30 wH/SL - 
5 SL/wH - 
6 31 RD/BL - 
6 
BL/RD - 
7 32 RD/OR VI 102 
7 OR/RD VR 102 
8 33 FD/GN - 
8 GN/RD - 
9 34 RD/BN - 
9 BN/RD - 
10 35 
RD/SL v-r 103 
10 SL/RD VR 103 
11 36 BK/BL - 
11 BL/BK - 
12 37 BK/OR - 
12 OR/BK - 
13 38 BK/GN vr 104 S...

IN!3TALJATION Injinite 4096 Hybrid Xey Telephone System 
CO1 TIP IN 
----- 
T -----s-w--- 
RJ2lX 
CnLW 
I CO1 RING IN 
--s-m e- 
-t +--------- 
Pl 
F!3 
COB SPARE 
STAl TIP OUT 
I ------------- 
I STAl RING OUT 
I r---------- 
I i 
1 I 
1 I 
1 I 
1 I 
1 I 
1 I 
STAl TIP IN 
--se- 
SLT INTERFACE 
STAl RING IN 
---A- 
I I 
EO”:tENT 
SCREW TERMINA POWER FAILURE TRANSFER 
-WUWL 
LEC CONTACT 
Figure 500-12 Power Failure Transfer Circuit (PM7 
500-18 Issue 1, January 1992  

units that can be installed in a System, but 
each unit uses a Key Telephone hterface cti- 
cult and 
this reduces station capacity on a 
one-per-one basis.  Infinite 4096 Hybrid Key Telephone System 
b. Take the RD/OR wire on the back of the 
terminal strip and route through the slot 
where the PFT is mounted and connect to 
the RD/OR wire on the back of the PFI’. 
C. Connect the appropriate wire (1 or 2) tie 
wrapped to the PFI’ mountfng hole to the 
Kl connector on the PFI’. 
d. Insert the PET into...

INSTALLATION InJinite 4096 Hybrid Key Telephone System 
GREEN VT 
r GREEN VT 
RED ,jk 
BLACK 
YELLOW 
WHITE IiT 
DR 
OT 
OR  RED ;k 
BLACK DT 
G-4 
GN 
0 
RD 
0 
BK YL 
9 
I 
ma- 
--% @wP 
Key Telephone Wiring Key Telephone with OHVA Wiring 
GREEN VT 
RED VR 
34  . 
GN 
0 
RD 
0 
BK YL 
8 8 
+  BLACK 0: 
- DR 
f 
‘s‘;-/s”  . A 
-$ 8 
I 
GN 
0 
RD 
0 
BK YL 
I 
L L 
DSS/DLS Console Wiring Single Line Telephone Wiring 
Figure 500-13 Station Modular Block Wiring 
500-20 Issue 1. January 1992  

Infinite 4096 Hybrid Key Telephone System 
INSTALIATION 
l 1 SIB board (installed in KSu)(supports 
8 SLTs) 
e 1 RG unit (installed into EPS Housing) 
0 1 APL board (installed in Basic KSUJ 
The SIB is color coded with green ejector tabs 
and is plugged into any designated K.IB card 
slot. Each SIB board supports eight tele- 
phones (standard DTMF Single Line Tele- 
phones and message waiting DTMF SLTs). 
The Ring Generator Unit IRG) must be installed 
into the External Power Supply Housing (EPS) 
to...

WALL MOUNT 
JACK 
HANDSET RETAINER 
TELEPHONE WALL MOUNT WALL MOUNT 
WALL JACK 
. 
 
. 
 
. 
. 
Figure 500-14 Key Telephone Wall Mounting 
500-22 
Issue 1, January 1992  

500.19 WALL, MOUM’ING THE TEL& 
PHONE 
All connections to the Key Telephone are fully 
modular. To wall mount the Key Telephone, It 
is necessary to have one Wall Mount Kit and 
one standard-type jack assembly designed for 
normal wall hanging applications. 
a 
b. 
C. 
d. 
e. 
f. Unplug the line cord fi-om the phone. This 
line cord will not be required and should 
be retained as a maintenance replacement 
item. 
Lift the plastic nixnber retainer upward 
and expose the screw underneath. Re- 
move the...

INSTUTlON Infinite 4096 Hyixid Key Telephone System 
RSM MODULE 
MOD 1 JACK 
EXT. PAGE VOICE 
MOD 2 JACK 
SIU MODULE 
r 
/ K 
Mounting Holes 
RED 
COLORED 
EXT. PAGE COMROL 
Figure 5OG15 Application Board (APL) 
500-24 Issue 1, January 1992  

Infinite 4096 Hybrid Key Telephone System 
INSTALLATION 
4 CONOUCTOA CORD h JACK 
MO3 1. EXTERNAL PAGE VOICE 
CONNECT0NS 
PIN 
APL 
a 
COCOA 
L 
2 
GN EPVT 
3 
RD EPVR 
APL BOARD 
--------1 EPBT 
EPBR 
9 r 4 4 YL EPMR 
--e--m-- / 
4 CONDUCTOR CORD 6 JACK 
MOO 2 - PAGING CONTROL CONTACTS 
6 CONDUCTOR CORD 6 JACK 
I.400 3. RAN CONNECTIONS’ 
4 3 
GN 
RANYT 
4 
RO RANVR 
2 BK RAN CTL 1 
6 WI4 RANSMi CONTROL 
CONTACTS 
VOICE LN 
> INPb-7 FACM RECORDED 
ANNOUNCEMENT DEVICE 
MAKE START CONTROC TO 
CONTROL 
1...

INSTALLATION 
Infinite 4096 Hybrid Key Telephone System 
Basic 
KSU 
APL MOD 1 JACK 
EXTERNAL PAGE OUTPUT CONNECTIONS 
PIN 1 - NOT USED 
PIN 2 - EPVT (VOICE) 
PIN 3 - EPVR (VOICE) 
PIN 4 - NOT USED 
MOD 1 JACI 
MOD 2 JACI 
MOD 3 JAC) APL MOD 2 JACK 
EXTERNAL PAGE CONTROL CONTACTS 
PIN 1 - EPMT (MAKE CONTACT) 
PIN 2 - EPBT (BREAK CONTACT) 
PIN 3 - EPBR (BREAK CONTACT) 
PIN 4 - EPMR (MAKE CONTACT) 
APL MOD 3 JACK 
RECORDED ANNOUNCEMENT (RAN) JACK 
PIN 1 - RAN SENSE (End of Message) 
PIN 2 - RAN CONTROL...