Vodavi Infinite 4096 Key Telephone System Installation And Maintenance Manual

Infinite 4096 Hybrid Key Telephone System IlEAsT COST ROUTTNG PROGRAMMING 
LCR PROGRAMMITV G fCont’d9 
I. Dtiy Start Time Table 
Progr~ Steps 
1. Press the DAILY SIXRT flexible button 
(button #69. The foilowing message will be 
shown on the display phone: 
Enter times in milKary form (2400 Hours) 
in succession. Pressing the HOLD button 
after each time entered. Default times are 
0800, 1700, 2300 (8 AM, 5 
PM, and 11 
PM). and the fourth time is disabled 
(####I. To change a start time all times 
must...

Idms~ COST ROUTING PROG-G 
Infinite 4096 Hybrid Key Telephone System 
L-CR PROGRAMMIN G (Cont’d) 
J. 
1. Weekly Schedule Table 
Programming Steps 
Press the WEEKLY SCHED flexible button 
(button #7). The following message wll.l be 
shown on the display phone: 
Where: 
0= Monday 
1= Tuesday 
2= Wednesday 
3= Thursday 
4= Friday 
5= Saturday 
6= Sunday 
T = Time Period Route List (l-4) to use for the 
time of day (based on the daily start time table). 
Enter values for all time periods specified in the...

InJinite 4096 Hybrid Key Telephone System 
UZA!ST COST ROVTING PROGRAMMING 
LCR PROG- G (Cont’d) 
K. LCR Routing 
for Toll Information 
Pr0grammln.g Steps 
1. Press TOIL INFO flexible button (button 
#8) The folIowIng message w-ill be shown 
on the display phone: 
2. Enter 2-digit Route Lfst number (00- 15) 
for the Route to be referenced in the Route 
List Table. 
3. Press HOLD after programmin g the Route 
number. Display will now update. 
Enable LCR at this point. Refer to System 
ProgrB. 
L. Default...

InjZnite 4096 Hybrid Key Telephone System 
-G DATA BASE PA&METERS 
SECTION 760 
INITIALIZING DATA BASE PARAMETERS 
760.1 SYSTEMPARAMETERS 
gmmmlng Steps 
If the system is in the programming mode, 
continue using program codes. If starUng to 
program here enter the programming mode 
tit (Refer to paragraph 700.2). 
If System Parameters are to be in&ializd: 
1. Press FLASH and dfal [70]. The following 
message will be shown on the display 
phone: 
2. To initialize the system parameter data 
base, press the...

INlTLALIzING DATA BASE PARAMETERS Winite 4096 Hybrid Key Telephone System 
Initializing Data Base Parameters (cont*a) 
760.2 g=oL.INEPARAMETERS 
Progr~ Steps 
If the system is in the programmIng mode. 
continue using program codes. If starting to 
program here enter the programming mode 
first (Refer to paragraph 700.21. 
If CO Une Parameters are to be Mtiaked: 
1. Press FLASH and dial [711. The followlng 
message wIU be shown on the display 
phone: Description 
Thisdatafieldisusedt.oinitialkeallCOLtne...

Infinite 4096 Hybrid Key Telephone System NITYALIZING DATA BASE PARAMETERS 
XnitiisLLtz~ Data Base Parameters (Cont’dj 
760.3 STATION PAIUMETERS 
Programming Steps 
lf the system is in the progmmming mode, 
continue using program codes. If .starUng to 
program here enter the programming mode 
first (Refer to paragraph 700.2). 
If Station Parameters are to be initialized: 
1. Press FLASH and dial (721. The following 
message w-ill be shown on the display 
phone: 
2. To inWake the Station Parameter data...

IM’rWJZING DATA BASE PARAMETERS Infinite 4096 Hybrid Key Telephone System 
Init.taJi~~ Data Base Pi=drameteR (Cant’4 
760.4 EX~~~PTION TABLES 
Programming steps 
If the system ls in the programming mode, 
continue using program codes. If starling to 
program here enter the programming mode 
first (Refer to paragraph 700.2). 
If EkcepUon tables are to be lnitlaJlzed: 
1. Press FLASH and dial (731. The following 
message wfll be shown on the display 
phone: 
Descllption 
This data field is used to...

Infinite 4096 Hybrid Key Telephone System 
INITMUZING DATA BASE PARAMETERS 
Initializing Data Base Parameters (Cont’dj 
760.5 SYSTEM SPEED DIAL 
gramming Steps 
If the system is in the programming mode, 
continue usfng program codes. If starUng to Description 
‘his data field is used to initialize the System 
Speed Dial entries. 
program here enter the programming mode 
first (Refer to paragraph 700.2). 
If the System speed dfal entries are to be 
illi-: 
1. Press FLASH and dial 1741. The following...

INITIALEINC DATA EM= PARAMETERS Infinite 4096 Hybrid Key Telephone System 
Initialize Data Base Parameters (Cont’dl 
760.6 LCRTABLES 
Proggxnm&g Steps 
If the system is In the programming mode. 
continue using program codes. If startkg to 
program here enter the programming mode 
first (Refer to paragraph 700.2). 
lf LCR tables are initializd: Description 
This data field is used to initialize the LCR 
Tables parameters. (Flash 6 1). 
1. Press FLASH and dial (751. The following 
message will be shown on...

Infinite 4096 Hybrid Key Telephone System PRINTING DATA BASE PARAMETERS 
SECTION 765 
PRINTING 
DATA BASE P-ERS 
765.1 FXINT ENTIRE SYSTEM DATA 
Programming Steps 
If the system is in the programming mode, 
continue using program codes. If starting to 
program here enter the programming mode 
first (refer to paragraph 700.2 1. 
If a complete printout of the entire data base is 
desired: 
1. Press FLASH and dial 1801. The following 
message will be shown on the display of a 
display phone: 
2. To print...