Vodavi Infinite 4096 Key Telephone System Installation And Maintenance Manual

Exception Tables Programming (Cont’d) 
D. Special Table Programmfng 
PrQg ’ g Steps 
To program a special table it is !Irst necessary 
to assign an area code to the table (except for 
the home area code). 
1. To assign an area code to a speclal table 
press the appropriate AREA X flexible but- 
ton (button #9- 11). The following display 
will be shown on the display phone: 
2. Enter the three (3) digit area code. 
3. Press the HOLD button. The display will 
now update. 
4. To enter office codes into the...

Infinite 4096 Hybrid Key Telephone System EXCEPTION TABLES PROGRAMMING 
Exception Tables Prog-ramming (Cont’d) 
E. Displaying Toll Table Entries 
PI-o,~~ Steps 
To display entries in either the Allow /Deny 
tables or the special tables press the DISP 
flexible button (button #12j while entering in- 
formation into a table. 
1. Wh.ile viewing entries made into an allow 
or deny table two (21 entries at a time will 
be displayed on the bottom line of the 
display. By pressing the DISP button 
again the...

In_Fnite 4096 Hybrid Key Telephone System I2M-T COST ROWrING PROGVG 
SECTION 755 
LEAST COST ROUTING PROGRAMMING 
A Introduction 
Least Cost Routing &CR) selects the most eco- 
nomical programmed route for an outgoing 
call. When a station user dials an outside 
number, the LCR feature analyzes the number 
and then automatically chooses an outside line 
from the group that has been programmed as 
most economical. The LCR feature puts the 
responsibility of choosing the least expensive 
route for each...

LEAST COST ROUTING PROGRAMMING Xnfinife 4096 Hybrid Key Telephone System 
process continues until an available Une is 
found, or the last available line group 
is 
searched ,or until a Une group is reached with 
a priority assignment lower than the station’s 
LCR Class of Service assignment. 
When a IJne is available the system will seize 
that line and watt for dial tone. Then before 
dialing, the system checks the Insert/Delete 
table for digits that should be deleted from the 
front of the number or...

Injinite 4096 Hybrid Key Telephone System LEAST COST ROUTING PROGRAMMING 
L.east cost Routing Progriunming cont’dl 
prO,aai~ Steps 
If you are in the program mode, continue using 
the program codes. If you are starting to pro- 
gram here, enter the program mode first. 
NOlE LCR must be disabled while program- 
mingorrnuking~estoanyoftheLCR 
tables. Refer to sec. 710.22 for insmns to 
disable LCR. 
1. To program the system for Least Cost 
Routing. press FLASH and dial [Sl]. The 
following message fs shown...

LEAST COST ROUI’ING PROGRAMMING Iniinite 4096 Hybrid Key Telephone System 
LCR PROG RAnUMlNG (Cont’d) 
D. B-Digit Ana/Of&e Code Table 
Programmkq Steps 
- 
1. Press 3-DIGTTTBL flexible button Button 
# 1). The following message wilI be shown 
on the display phone: 
Where: 
L = [O] for non leading 1(-l” not dialed) 
111 for leading l(‘1” is dialed) 
NNN = area/office code 
RR = route list number 00- 15 
6 = [O] do not go to 6 digit table 
[l] go to 6 digit table 
PP = number of digits expected to be...

Injinite 4096 Hybrid Key Telephone System UMST COST ROVTING PROGRAMMING 
UIR PROGRAMMIN G (Cont’d) 
F. 
1. Ekctption Code Table 
FTogrw Steps 
Press EXCEPTTEIL flexible button (Button 
#3]. The following message will be shown 
on the display phone: Description 
Exception Table. This table is used for opera- 
tar calls and any other calls which would use 
a one- or two-digit entry rather than a three- 
cligit area code. 
Where: 
S = (01 to remove code from table 
[ 11 to add code to table 
XX= exception...

LEAST COST ROUTING PROGBWMJiNG Infinite 4096 Hybrid Key Telephone System 
LCR PROGW G (Cont’d) 
G. 
1. Route List Table 
progamming Steps 
Press the ROUIX LIST flexible button 
(Button #4). The following message will be 
shown on the display phone: 
Where: 
2. 
3. 
4. 
5. RR = Route List Table number 00- 15 
T = Time Period Route list l-4 
G = CO Line Group 1-7 
DD = Insert/Delete Table reference 00- 19 
(## for none) 
L = LCR Class of Service WOS) 
Press HOLD. Display will now update. 
To enter...

Infinite 4096 Hybrid Key Telephone System 
IJUST COST ROVTING PROGRAMMING 
LCR PROG RAMMING (Cont’d) 
Route List Table (Cont.4 
FroFfr-g 
Description 
LCR COS Priority. A station should be as- 
signed a class of service for LCR (refer to staff on 
programming, Sec. 730). The LCR COS can be 
between 0 and 6, with 0 being unrestricted and 
6 being the most restrictive. Within the time 
period route List Table, line groups are given 
an LCR COS Priority assignment between 0 
and 6. A station using LCR will...

LEAST COST ROUTING PROGRAMMING InI%tite 4096 Hybrid Key Telephone System 
LCR PROG RAMMlNG (Cont’d) 
H. 
1. Insert/Delete Table 
Programming Steps 
Description 
Press INS/DEL TEiL flexible button (but- 
ton #5). The following message will be 
shown on the display phone: Insert/Delete Table. Digits can be either 
added or deleted when dialing a number. For 
instance, If a user dials a long distance calI that 
should be placed on a foreign exchange FXI 
line. the digit 111 and the three d@t area code 
0...