Home > Trane > Air Conditioner > Trane Intellipak 2 Service Manual

Trane Intellipak 2 Service Manual

Here you can view all the pages of manual Trane Intellipak 2 Service Manual. The Trane manuals for Air Conditioner are available online for free. You can easily download all the documents as PDF.

Page 91

Installation
RT-SVX24K-EN91
Figure 59. Typical field wiring diagram for 90 to 162 ton VAV control options 

Page 92

Installation
92RT-SVX24K-EN
Figure 60. Typical field wiring diagram notes for 90 to 162 ton VAV and CV control options 

Page 93

Installation
RT-SVX24K-EN93
Figure 61. Typical GBAS analog input wiring diagram for 90 to 162 ton CV and VAV control options
Note:See Figure 64, p.  101 

Page 94

Installation
94RT-SVX24K-EN
Table 35. GBAS voltage vs. setpoint
SetpointGBAS 0-5 VDCGBAS 0-10 VDCValid Range
Occ Zone Cooling Setpoint(CV only)0.5 to 4.5 VDC0.5 to 9.5 VDC50 to 90°F
Unocc Zone Cooling Setpoint 0.5 to 4.5 VDC 0.5 to 9.5 VDC 50 to 90°F
Occ Zone Heating Setpoint(CV only)0.5 to 4.5 VDC0.5 to 9.5 VDC50 to 90°F
Unocc Zone Heating Setpoint 0.5 to 4.5 VDC 0.5 to 9.5 VDC 50 to 90°F
SA Cooling Setpoint (VAV only)0.5 to 4.5 VDC0.5 to 9.5 VDC40 to 90°F
SA Cooling Setpoint (SZVAV only) 0.5 to 4.5 VDC...

Page 95

Installation Checklist
RT-SVX24K-EN95
Installation Checklist
General Checklist (applies to all units)

Unit checked for shipping damage and material
shortage
Verify that the installation location of the unit will
provide the required clearance for proper operation
 Roof curb assembled and installed
Roof curb level and square
Ductwork secured to curb, or unit
Corners of duct adapters sealed on units with horizontal
supply or return
Horizontal supply or return ductwork is self supporting
Pitch...

Page 96

Installation Checklist
96RT-SVX24K-EN
Using 0.75 x 24 threaded rod pull and secure
evaporator section and outside air section together
Using .375 bolts, nuts and washers pull and secure the
roof rails together
Installed roof splice plate
Added bullwrap to electrical wiring between
evaporator and outside air section
Connected power and control wiring between
evaporator and outside air section
Gasket applied and side panels installed on unit split
Butyl tape applied on top of unit split along roof...

Page 97

Installation Checklist
RT-SVX24K-EN97
Energy Recovery Wheel
Verify that the wheel turns freely though a full rotation
Confirm that all wheel segments are fully engaged in
the wheel frame and that the segment retainers are
completely fastened
Confirm the seal adjustment and proper belt tracking on
the wheel rim 

Page 98

98RT-SVX24K-EN
Unit Startup
Sequence of Operation
Cooling Sequence of Operation
Time delays are built into the controls to increase
reliability and performance by protecting the compressors
and maximizing unit efficiency.
SZVAV Cooling Sequence of Operation
Single Zone VAV units will be equipped with a VFD
controlled supply fan which will be controlled via the 0-
10VDC RTM VFD output and the RTM Supply Fan output.
With the RTM Supply Fan output energized and the RTM
VFD output at 0Vdc the fan speed...

Page 99

Unit Startup
RT-SVX24K-EN99
Low Ambient Compressor Operation
Certain applications require compressor operation at
lower ambient conditions than standard units. Low
ambient compressor operation is a factory configured
option that allows units to operate down to -10°F by
extending the low ambient compressor lockout setpoint
range.
Standard configuration units are limited to a minimum
low ambient compressor lockout setpoint of 40° F. In
conditions below 40°F the low-pressure cutout (LPC)
switch can open in...

Page 100

Unit Startup
10 0RT-SVX24K-EN
The drain control can be configured via the Human
Interface, and by the drain actuator installation, to hold or
drain water on power loss; the default is set to drain.
Periodic purge is a cyclic opening of the drain to remove
debris and buildup from the sump and add additional
fresh water to the sump. Periodic purge has an adjustable
interval from the setup menu on the Human Interface with
a range of 1-12 hours or can be set to disabled - the default
position if periodic...
Start reading Trane Intellipak 2 Service Manual

Related Manuals for Trane Intellipak 2 Service Manual

All Trane manuals