Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

System & Station
Program 04 – Station Logical Port [PDN] Assignment
Strata DK Programming 5/993-15
System & Station
Program 04 Overview
Program 04 assigns the Primary Directory Number [PDN] to each telephone (logical port). [PDNs] 
can be one to four digits. [PDNs] must not conflict with Phantom Directory Numbers [PhDNs] or, 
DK424 Distributed Hunt Directory Numbers set in Program 
04.
[PDNs] can be changed using Program 04, but door phone and modem numbering cannot.
lDoor phone standard numbering is...

System & Station
Program 04 – Station Logical Port [PDN] Assignment
3-16Strata DK Programming 5/99
Program 04 Example
Action (press buttons+LED buttons)LCD Response
1. Use an LCD programming phone per Minimum Hardware 
Requirements in Chapter 1 - Overview.No. N-N
1
Jan 20 Sun 06:43
1. N-N = program telephone [PDN]
2.****Enter programming mode. (Do not press the [DN] button.)Program Mode
3.
6SNU6SHDNHU+ROGAccess Program 04. The speaker beeps to indicate when to enter a 
program number. Program...

System & Station
Program *04 – [PhDN] and Distributed Hunt [DN] Assignments For Internal and Tie Line Calls
Strata DK Programming 5/993-17
System & Station
Program *04 – [PhDN] and Distributed Hunt [DN] 
Assignments For Internal and Tie Line Calls
Processor Type:DK14, DK40i, all RCTUs
Program Type:Station
Initialized Default:See the legend below




  6SNU
  +ROG  6SNU  +ROG 6SNU+ROG 6SNU+ROG
Processor[PhDN] Port RangeInitialized [PhDN]DH [DN] Port RangeInitialized DH [DN]
DK14...

System & Station
Program *04 – [PhDN] and Distributed Hunt [DN] Assignments For Internal and Tie Line Calls
3-18Strata DK Programming 5/99
Program *04 Overview
Program *04 assigns the system Phantom Directory Numbers [PhDNs] and Distributed Hunt (DH) 
Group [DNs].
All DK systems provide 16 DH groups. [PhDNs] and DH [DNs] can be one to four digits.
[PhDNs] and DH [DNs] cannot conflict with each other, or be the same as Primary Directory 
Numbers assigned in Program 04. [PhDNs] can not conflict with, or be...

System & Station
Program 05 – Flexible Access Code Numbering
Strata DK Programming 5/993-19
System & Station
Program 05 – Flexible Access Code Numbering
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:See record sheet




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Default 
Access 
CodeFeatures Affected
(N/A = Not Affected/ Cannot Change)New 
Access 
Codes
0Unused
1
Voice First/Tone First (Dial 1-N/A)
Door Phones: (#151~#159; #161~#163)
IMDU or RMDS Access:...

System & Station
Program 05 – Flexible Access Code Numbering
3-20Strata DK Programming 5/99
4
Default [PDNs] and Park Orbits (see Program 04)
Default [PhDNs] (see Program 
*04)
Automatic Callback (Dial 4-N/A)
CO Line Queuing (Dial 4-N/A)
Station Number Display (#401)
Port Number Display (#402)
Hold (#41)
Hold Pickup (#42)
Automatic Busy Redial (Conf + #44)
Automatic Busy Redial Cancel (Int + #44)
Message Waiting Answer (#408) from INT, [PDN], or 
[PhDN]
Display [PDN], [SDN], or [PhDN] on LCD (#407)...

System & Station
Program 05 – Flexible Access Code Numbering
Strata DK Programming 5/993-21
System & Station
Program 05 Overview
Program 05 enables you to change feature access codes. The first digit of a feature access code can 
be changed to a different digit or to two digits. Digits after this prefix cannot be changed. Some 
access codes cannot be changed (such as the code for Automatic Callback) and are shown with N/
A on the record sheet.
Notes
lAccess code conflicts may exist if new access codes...

System & Station
Program *05 – Call Park Pickup Abbreviated Dialing
3-22Strata DK Programming 5/99
Program *05 – Call Park Pickup Abbreviated Dialing
Processor Type:DK14, DK40i, All RCTUs
Program Type:System
Initialized Default:Blank
Program 
05 Overview
This program assigns two Call Park Pickup abbreviated dialing codes to pick up parked calls. For 
dialing convenience, the 1- (or 2-) digit abbreviation for Call Park Pickup replaces the Call Park 
access codes #331 and #332. To park calls, Code #331 and...

System & Station
Program 09 – Built-in Auto Attendant Prompt / Station Assignments
Strata DK Programming 5/993-23
System & Station
Program 09 – Built-in Auto Attendant Prompt / Station 
Assignments
Processor Type: DK14, DK40i, All RCTUs
Program Type:System and ACD
Initialized Default:Blank
Program 09 Overview
Program 09 tells the system where to direct calls after incoming Auto Attendant callers dial a 
digit(s) in response to the menu of dialing prompts offered by one of the Auto Attendants digital...

System & Station
Program 09 – Built-in Auto Attendant Prompt / Station Assignments
3-24Strata DK Programming 5/99
äTo create one-digit dialing prompts and to assign the associated destination station numbers
1. Enter Program 09.
2.When “SELECT
” appears on the LCD, press the desired digit (prompt). Then “AUTO ATT 
DIAL
” appears on the LCD.
3. Enter the destination DH or station [PDN] (not Port number) number or 
 plus the ACD 
group (per Note) associated with the prompts and then the 
+ROG button.
4....