Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

Overview
Alphabetical Program Listing
Strata DK Programming 5/991-7
Overview
Feature or TopicProgram Number
Account Codes 15, 70, 39, 69, 30, 60
ACD03, 09, *09, 10-4, 11,
14-0, 14-1, *14-1, 14-2,  *14-2, 
14-3, 14-4, 14-5, 14-6, 14-8, 14-
9, 14-71, 14-72, 14-73, 15, 17, 
18, 35, 39, 71-1~3
Add-on Module *29
Alarm Sensor 39
All Call Voice Page 05, 10-2, 31, 39
Alert Signal 39
Alternate Point Answer 10-1
Amplified Conference 
(External)10-2, 10-3
ANI10-3, 20, 39, *51, *52, 59, 60-1, 
71-0~5), 72, 77-4...

Overview
Alphabetical Program Listing
1-8Strata DK Programming 5/99
DNIS12, 17, 20, 60-1, 71-(0-5), 72,
77-4
Do Not Disturb 39
Do Not Disturb Override 05, 30
Door Lock Control 39, 77-1, 77-2
Door Phones 05, 77-1, 77-2, 79, *79
DSS Console Features 03, 28, 29-1~29-8, 10-2
DSS DKT/EKT 28
DTMF and Dial Pulse 
Assignments10-1, 15, 30, 39
DTMF Receiver (QRCU3, 
K5RCU, RRCS) Operation03, 12, 15
DTMF Signal Time, CO lines 
(80/160 ms)10-1
DTMF Signal Time, VM Ports 
(80/160 ms)10-2
DTMF Tone/No Tone/Padded...

Overview
Alphabetical Program Listing
Strata DK Programming 5/991-9
Overview
Physical Port Display/Change 02
Pooled CO Lines 16, 39
Pooled Line Buttons 16, 39
Pooled Line LED – No Flash 31
Port/Station Number 
Assignment04
Privacy/Non-Privacy 31, 30, 39
Privacy Override 10-2, 30, 31
RAM Test (see Memory Test) 00 (Part 2)
Redial Last Number 39
Remote Administration and 
Maintenance00, 03, *09, 77-1, 78
Repeat Last Number Dialed 39
Ring Transfer 10-1, 37
Ringing Repeat 10-1
Ring Tones 80
Ring Flash...

Overview
How to Program a Strata DK System
1-10Strata DK Programming 5/99
How to Program a Strata DK System
Fill out the record sheets that are provided, then enter this data using a 20-button LCD digital 
(DKT) or electronic (EKT) telephone. Strata DK enables you to enter data from an on-site or off-
site PC with Toshiba DKAdmin software. Toshiba highly recommends this easier method of 
programming.
DK14/DK40i: the programming telephone must be any 20-button LCD DKT (or EKT, DK40i 
only). The DKT must...

Overview
How to Program a Strata DK System
Strata DK Programming 5/991-11
Overview
Program Sequence
Detailed data entry instructions are on the top of each record sheet (see Figure 1-2).
äTo use the program sequence on the record sheet
1. From the programming telephone, enter the programming mode by pressing a series of shaded 
buttons. The shaded buttons represent the entry sequence for all programs.
2. Enter the program number. This sequence is unique for every program. The buttons are white 
on every...

Overview
How to Program a Strata DK System
1-12Strata DK Programming 5/99
Programming Data Variations
There are two different ways to enter data in Step 3 (Figure 1-2) of a program: pressing the buttons 
on the dial pad and pressing the LED buttons. Many programs are multidimensional and involve 
both types of entry.
Simple Programs
Simple programs such as Program 00, only require data to be specified through the dial pad. Data 
entered from the dial pad displays on the programming digital or electronic...

Overview
How to Program a Strata DK System
Strata DK Programming 5/991-13
Overview
äTo check the status of a CO line in Program 15
1. Press the 
0RGH button (below the LCD) after entering the program code. 
2. Then enter the CO line number to be verified. 
3. Press 
 to display the status of the CO line and to advance to the next CO line.
Programming LED Buttons Keystrip Template
You place a special buttonstrip template (see Figure 1-3) over the 20 flexible feature buttons of the 
programming telephone....

Overview
First-time Programming
1-14Strata DK Programming 5/99
First-time Programming
Follow these general procedures the first time you install a system or after major hardware changes 
and/or you need to start from scratch.
Step 1: Check Minimum Hardware Requirements
A system must have the following minimum hardware installed for programming, as described in 
the Installation chapters of the Strata DK Installation and Maintenance Manual.
äTo check hardware requirements on the DK14 and DK40i
1. Make...

Overview
First-time Programming
Strata DK Programming 5/991-15
Overview
©Timed Reminders
©Digital Telephone Volume Levels
©Call Forward Memory (Power OFF, then ON).
©Station Message Waiting Status
©Caller ID Lost Call Memory
2. Install all PCBs. Run Program 91-1 to inform the software of the system hardware 
configuration.
Step 3: Run Programs 03 and 19-1
1. Run Program 03 for all PCBs that have options.
2. Run Program 19-1 to inform the software of the system option Alternate BGM slot.
Step 4: Run...

Overview
Programming Examples
1-16Strata DK Programming 5/99
Programming Examples
Some commonly used programs have explicit examples (listed below). Refer to these pages to 
help familiarize you with running these programs.
ProgramPage
Program 91-9—System Initialization2-2
Program 90—Initializing Programs 00~*992-4
Program 91-1—Automatic PCB Recognition and Logical/Physical Port Initialization2-6
Program 92—Initializing Speed Dial Numbers, VM ID Codes, Character Message Memory, 
Timed Reminders, Digital...