Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

Initialization & Test
Program 92 – Initializing Misc. Backup RAM
Strata DK Programming 5/992-11
Initialization & Test
7.6SNU6SHDNHUPrepare system for another selection (go back to Step 5) or exit 
Program 92 (continue with Step 8).92 Select =
8.
+ROGInitialized data in system memory (LEDs got out).92 Select = ##
Data Programmed
9.
6SNU6SHDNHUExit Program 92. Enter another program number (see “Program 30 – 
Station Class of Service” on Page 3-73) or exit programming mode (go 
to Step 10). System...

Initialization & Test
Program 00 – Part 1: Software Check
2-12Strata DK Programming 5/99
Program 00 – Part 1: Software Check
Processor Type:DK14, DK40i, All RCTUs 
Program Type:Test - Includes: Remote Maintenance Security Code Assignments
Initialized Default:None




  6SNU   +ROG  6SNU +ROG 6SNU+ROG 6SNU+ROG
Select = CodeItemPassword or S/W 
Check CodesLCD Display
0ROM Version (not programmable)
Version =
11st Level PasswordPassword =
22nd Level PasswordPassword =
8Software RAM...

Initialization & Test
Program 00 – Part 1: Software Check
Strata DK Programming 5/992-13
Initialization & Test
Program 00 Part 1 - Overview
This program enables you to run various checks on the Strata DK System.
DK14: the QKYS feature key must be installed on the QRCU3 PCB to allow AA.
DK40i: the KKYS feature key must be installed on the K5RCU PCB to allow AA.
DK424: the RKYS feature key must be installed on the RCTU to allow AA, ACD, and ACD/MIS.
Code 0, ROM Version
Code 0 displays the software version...

Initialization & Test
Program 00 – Part 1: Software Check
2-14Strata DK Programming 5/99
1111
Define the Level 1 remote maintenance security code from the System 
Record Sheet (four digits maximum). Level 1 allows remote access to 
all programs and data. Default Level 1 security code is “0000.”
or...00 Select = 1
Password = 0000
1111
Define the Level 2 remote maintenance security code from the System 
Record Sheet (four digits maximum). Level 2 allows remote access to 
programs 30~39 and 77~89 only....

Initialization & Test
Program 00 – Part 2: Processor RAM Test
Strata DK Programming 5/992-15
Initialization & Test
Program 00 – Part 2: Processor RAM Test
Processor Type:DK14, DK40i, All RCTUs 
Program Type:Test - Includes: Remote Maintenance Security Code Assignments
Initialized Default:None
General RAM Test
NoteSee “Program 00 Part 2 - Overview” on Page 2-16
Display General RAM Test Results
Backup RAM Test




  6SNU   +ROG  6SNU  +ROG Tests RAM (15 seconds downtime)




 ...

Initialization & Test
Program 00 – Part 2: Processor RAM Test
2-16Strata DK Programming 5/99
Display Backup RAM Test Results
Program 00 Part 2 - Overview
Use this program to test the RAM on system processor. If a RAM test error occurs during this test, 
the processor causing the error should be replaced. In the case of two-PCB processors, isolation of 
a RAM failure is indicated on the programming telephone X or Y (see above).
If the DK14 or DK40i processor fails the RAM test, the Base KSU must be...

Strata DK Programming 5/993-1
System & Station
System & Station3
This chapter gives you programming information for the Strata DK system and its stations.
Program 01 – Station Logical Port Display and/or 
Change
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:Logical port number = physical port number 
Program 90, 91-1, or 91-9 initializes Program 01
Program 01 Overview
Program 01 enables you to enter a physical port to display the associated logical port. You then 
have...

System & Station
Program 02 – Station Physical Port Display and/or Change
3-2Strata DK Programming 5/99
Program 02 – Station Physical Port Display and/or 
Change
Processor Type:DK14, DK40i, All RCTUs
Program Type:Station
Initialized Default:Logical port number = physical port number
Program 90, 91-1, or 91-9 initializes Program 02
Program 02 Overview
Program 02 enables you to enter a logical port to display the associated physical port. You then 
have the option to assign a new physical port to the...

System & Station
Program 03 for DK14 – Slot Assignments
Strata DK Programming 5/993-3
System & Station
Program 03 for DK14 – Slot Assignments
When DK14 is powered ON, Program 03 automatically assigns the correct codes for installed 
PCBs. No record sheet is needed. Refer to the following table for PCB slot and slot code 
information:
DK14 Base KSU
Notes
lIn the DK14 software: QCDU2 digital ports are considered to be installed in slot 11. QCDU2 
CO lines are considered to be installed in slot 12....

System & Station
Program 03 for DK40i – Flexible PCB Slot Assignments
3-4Strata DK Programming 5/99
Program 03 for DK40i – Flexible PCB Slot Assignments
Processor Type:DK40i
Program Type:System
Initialized Default:PCB codes of PCBs installed prior to running Program 91-1 or Program 91-9
Code 00 for empty slots (15~18), Base KSU has codes for PCBs




  6SNU   +ROG  6SNU +ROG Turn System Power OFF (5 sec) then ON
PCB Code Reference Table
PCB Fixed SlotCodePorts/Type
Common Control 91 None...