Toshiba Strata Dk14, Dk40i, Dk424 Programming Manual

System & Station
Program 15 – Ground/Loop/Tie/DID Line Options
Strata DK Programming 5/993-45
System & Station
Program 15 Overview
This program specifies operational options on a line by line basis.
Code 0: Automatic Release (AR) on Voice Mail or Voice Calls
On loop start CO lines, some COs send the AR (Automatic Release) or CPC (Calling party 
Control) signal after an external party hangs up (typically 1~15 seconds) to disconnect a loop start 
line. An AR/CPC signal is a 95 or 450-millisecond open of...

System & Station
Program 15 – Ground/Loop/Tie/DID Line Options
3-46Strata DK Programming 5/99
Two-CO line DISA calls always release when AR/CPC is sent. DISA release via AR/CPC is not 
related to this program. CO line calls disconnected by the AR/CPC signal will be represented on 
the Station Message Detail Recording (SMDR) report by a “
*” next to the CO line number. Code 3 
does not apply to ground start lines, which automatically disconnect when the external party hangs 
up. See Important! note in...

System & Station
Program *15 – CO Line Tenant Assignments
Strata DK Programming 5/993-47
System & Station
Program *15 – CO Line Tenant Assignments
Processor Type:DK14, DK40i, All RCTUs 
Program Type:System
Initialized Default:All CO lines assigned to Tenant 1
Program 
15 Overview
A system CO line can be shared by more than one business tenant for the purpose of separating CO 
line ringing pickup and Night Transfer. Program 
15 assigns CO line business tenants.




  6SNU
  +ROG  6SNU  +ROG...

System & Station
Program 16 – Assign CO Line Groups (or Dial 9)
3-48Strata DK Programming 5/99
Program 16 – Assign CO Line Groups (or Dial 9)
Processor Type:DK14, DK40i, All RCTUs 
Program Type:System
Initialized Default:All CO lines assigned to the Dial 9 group




  6SNU   +ROG  6SNU+ROG 6SNU+ROG 6SNU+ROG
Processor TypeCO Line RangeCO Line GroupsProcessor TypeCO Line RangeCO Line Groups
DK14 001~004 01~04 RCTUBA/BB 001~048 01~08
DK40i 001~012 01~08 RCTUC/D 001~144 01~16
RCTUA 001~016...

System & Station
Program 16 – Assign CO Line Groups (or Dial 9)
Strata DK Programming 5/993-49
System & Station
Program 16 Overview
Use Program 16 to assign each CO line to a CO line group or a general “dial 9” group. A general 
group for outside calling is available with a “dial 9” access code as the initialized state for all lines.
Lines can be accessed with a dialing code instead of with a CO 
/LQH button. This is useful for 
WATS lines or other facilities, and is heavily used in Least Cost Routing...

System & Station
Program 17 – DID/Tie Line Options
3-50Strata DK Programming 5/99
Program 17 – DID/Tie Line Options
Processor Type:DK40i, All RCTUs
Program Type:System
Initialized Default:LED 01/02 OFF, LED 03/04 ON
Program 17 Overview
Program 17 assigns lines for Tie and DID operation.
Important!When normal Tie/DID lines are configured with Program 71 and 72 DNIS 
assignments, turn LED 05 ON and LED 06, 07 and 08 OFF for those lines - then 
program the lines as required in Programs 71 and 72.
Notes...

System & Station
Program 17 – DID/Tie Line Options
Strata DK Programming 5/993-51
System & Station
LED 08: ANI/DNIS Digit Format
Most DID/Tie lines with ANI/DNIS digit format include 

 tone with digits (LED 08 ON). One 
exception, as of this writing, Sprint provides DNIS without ANI and does not include 

 tone with 
digits - in this case LED 08 should be turned OFF.
Examples of this signal format are: 

ANI digits
DNIS digits
 and 
DNIS digits
.
DID/Tie lines with normal digit format does not include
...

System & Station
Program 17 – DID/Tie Line Options
3-52Strata DK Programming 5/99
LED 03: DID Camp-on/Busy
Turn LED 03 ON if DID line callers should hear ringback tone and camp on to busy stations when 
calling busy stations. Turn LED 03 OFF if the DID callers should hear busy tone when calling 
busy stations. Analog Tie lines will not camp-on to busy stations.
It is recommended to turn LED 03 ON for all DID lines. To provide Camp-on-busy over RDTU 
Tie line calls, configure Tie lines as DID lines in...

System & Station
Program *17 – DID Intercept Port Number (Vacant or Wrong Number)
Strata DK Programming 5/993-53
System & Station
Program *17 – DID Intercept Port Number (Vacant or 
Wrong Number)
Processor Type:DK40i, All RCTUs 
Program Type:System
Initialized Default:No data
Program *17 Overview
DID and/or DNIS calls in which callers have dialed a vacant or invalid port can be routed to 
intercept ports assigned with this program. Each DID and/or DNIS line can have its own intercept 
port. In all cases,...

System & Station
Program 19 – Alternate Background Music Source Slot Assignment
3-54Strata DK Programming 5/99
Program 19 – Alternate Background Music Source Slot 
Assignment
Processor Type:DK40i, All RCTUs (not used for DK14. See Program 10-2, LED 10)
Program Type:System
Initialized Default:Slot 11
Program 19 Overview
The PCB connected to the alternate BGM source can be in any slot. Use this program to designate 
that slot. LEDs 09 and 10 in Program 10-2 should be OFF if the source is connected to a...