Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

							INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
NMDU PCB 
30 
5 
32 
7 
34 
9 
36 
CKT TL8 ; j 7 I ,3 
RL7 i ; 4. 
I ’ 
CKT RL8 ; ! 
8 ’ I 
,5 
’ 
.- : 
- 1 500/2500-TYPE 
CROSS-CONNECT 
BLOCK 
FiJil 
BLOCK 
-. 
( I ’ I 
W-W ; I TLl 
(BL-W) ! ; RLI 
W-G) ’ I 
; i TL2 
(G-W) : 1 
TO TELEPHONE #2 RL2 
’ I 
W-S) ; ; TL3 
I TO TELEPHONE #3 RL3 
TL4 
TO TELEPHONE #4 RL4 
TL5 
RL5 
1 
TO TELEPHONE #5 
TL6 
I TO TELEPHONE #6 RL6 
TL7 
TO TELEPHONE #7 RL7 
TL8 
TO TELEPHONE #8 RL8 
 ‘25-PAIR CABLE 
“J” CABLE CONNECTOR PINS 
FIGURE 4-66-STANDARD TELEPHONE CONNECTION 
4-59  
						

							INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
, NMDU PCB CROSS~ 
CKT 
1 
CKT 
2 
CKT 
3 
CKT 
5 
CKT 
6 
CONNECTOR PINS CONNECT BLOCK  
RJII  
DDll (W-BL) I-: * TLl 
I 
(BL-W) ; , RLl 
(W-G) i / 
I TL2-L TO 
6-W ; i 
I 
RC~ -- DDIU #2 
(W-S) ] ! 
TL3 2 ‘1 -rn 
I 
(S-W) ; ! 
FiL3 
I ’ 
(R-0) I TL4 
(O-R) ; ’ RL4 
I ’ 
(R-BR) : ’ 
! I TLS 
(BR-R) . 
’ I RL5 
W-B’-) f , TL6 
J 
MODEM #2 - 
I 
TO 
MODEM #3 
1 
l CORRECT 
TO 
POLARITY 
MODEM #4 
25-PAIR CABLE J-MA 
FIGURE 4-67-MODEM POOLING CONNECTION (DDIU-MA ONLY) 
3) Using Tables 5-8 and 5-15 for guides: 
l Connect the trunks selected for emer- 
gency use to the Jl block “CO Tip” and 
“CO Ring” terminals. 
l Connect the NCOU circuits supporting the 
emergency trunks to the Ji block “NCOU 
Tip” and “NCOU Ring” terminals. 
4) Using Tables 5-6, 5-7, 5-9, 5-14 and 5-16 for 
guides: 
l Connect the standard telephone stations, 
designated for emergency use, to the 
properterminals on the J2 block“TELTip” 
and “TEL Ring” terminals. 
5) At the MDF, connect the DPFT to the system 
as follows: 
PERCEPTION, 
DPFT Jl (trunk) = LCEWNCEC-M & S J8-J15/ 
J508-J515 Pin 25 (S-V) = Pin 25 (S-V)* 
Pin 50 (V-S) = Pin 50 (V-S)* 
DPFT 52 (station) = LCEWNCEC-M & S J4- 
J15/J504-J515 
PERCEPTION, 
Any trunk position 
*On the J7 connector, the pin 25 connection 
provides the -24 VDC input required to drive 
the DPFTand the pin 50 connection provides 
ground, There are no power connections on 
connector J2. 
9.20 Reserve Power 
9.21 Install Reserve Power as follows (Figure 4- 
68): 
1) Place the customer-supplied battery pack 
where it will be located. 
4-60  
						

							CA UT/ON! 
Batteries can emit fumes that are poison- 
ous to people, potentially explosive, and 
corrosive to electronic components. Lo- 
cate batteries so that any fumes are ade- 
quately vented per local fire codes. 
2) Place the POWER switch (on the front of the 
main power supply) in the OFF position and 
remove the AC power cable from the outlet. 
3) Connect the battery pack leads (customer- 
supplied) to TB2 BAT on the NPSA-M or LPSA 
(Figure 4-68). Observe the correct polarity. 
Leave the leads from the peak load battery 
PEAK LOAD 
I I IllIll \\I 
POWER 
NOTE: CABLE 
Ensure that the correct 
polarity is maintained. 
FIGURE 4-68-RESERVE POWER INSTALLATION 
4-61 
4) Connect the leads to the battery pack (Figure 
4-67). Observe the correct polarity. Fix battery 
leads to the cabinet using the clamp. 
5) Place the BAT BACK UP switch on the front of 
the main power supply in the ON position. 
INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
6) Plug the AC cable into the outlet and turn the 
POWER switch ON. 
9.30 Paging Equipment 
9.31 By combining a single customer-supplied 
paging amplifier with the system’s paging interface 
and speaker zone switching, it is possible to pro- 
vide a paging system of up to five zones with All 
Zone Page capability. 
9.32 Figures 4-69, 4-70 and 4-71 show possible 
paging arrangements. As a standard feature (part 
of the NPRU PCB), the system provides a 600-ohm 
output to a paging amplifier. If more than one 
paging zone is required, the output of the amplifier 
can be routed back to the NPRU PCB where it will 
be switched to one of five sets of speakers. The 
speaker operated is determined by the access 
code dialed by the station user. The actual access 
code is assigned in software (see Section 200-255- 
300, Programming). 
9.33 An All Page code can also be defined in 
software. When that code is dialed, all relays will be 
activated simultaneously to permit paging to all 
speaker zones. 
9.34 If the power loads of the different zones are 
such that a single amplifier is not suitable, multiple 
amplifiers (up to one for each zone) can be con- 
nected as shown in Figure 4-71. 
9.35 If music is to be broadcast over the paging 
system, two arrangements are possible: 
1) If the music is supplied from a separate ampli- 
fier (as in Figures 4-70 and 4-71), it can be 
connected between the speaker common line 
and the PG GND input to the NPRU 
(PERCEPTlONe J2/J502 and pin 2 or 
PERCEPTlONe, Jl/J2 and pin 2). The music 
will be connected to all speaker zones when 
no page is in progress. When a page access 
code is dialed, the music is disconnected from 
the zone and the page amplifier output is 
connected. 
2) If the music is connected to a second input Of 
the paging amplifier (Figure 4-69), the PG1  
						

							INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
I Pe -J2/J502 
jl,, -..  x-1 %x-J1/J2 3c: L 
I 
<  I 
I- IN- 
; PRl 
1 #I I 
I 
I 
I 
I 
 I IThA ---t e- 
I I 
I -mm-, 
I 
MUSIC i 
1-e-m-q 
I SOURCE : 
,,,,-,,-,,,,,,J I 
FIGURE 4-69-PAGINGWlTHMUSlCOVEREXTERNALSPEAKERFROMSAMEAMPLlFlER 
control lead (52 and J502 pin 27 or Jl and 52 
for PERCEPTION,&,, , respectively) can be 
connected to the MUTE terminal of the page 
amplifier music channel. When any page ac- 
cess code is dialed, a ground output is applied 
to the PGl lead to mute the music. 
9.36 All paging connections are made at the J2 and 
J502 or Jl and 52 connectors on the 
PERCEPTION,&,, 
systems, respectively. The 
connectors are located on the rear of the basic and 
expansion cabinets. See Tables 5-4 and 5-10 for 
details, 
9.40 Music-on-Hold 
9.41 A Music-on-Hold (MOH) interface is a stan- 
dard feature on the system. The circuitry occupies 
part of the NPRU PCB. If MOH is equipped, it will be 
heard by any station or trunks on-hold in the sys- 
tem, or by any trunk put into the camp-on state. 
9.42 A tuner or other program source, supplied by 
the customer, is connected to the MOH input via pins 
4 and 29 (Br-W and W-BR) of J2 or J502 / Jl or J2 
forthe PERCEPTION 
e&ex systems, respectively (see 
Tables 5-4 and 5-10). The input impedance is 600 
ohms. (This cannot be the same source used to 
provide music over external speakers.) 9.43 Adjust the MOH volume with the MOH vol- 
ume control on the front of the NPRU PCB. Maxi- 
mum volume is limited by internal circuits in order 
to comply with FCC regulations. 
9.50 Universal Night Answer 
9.51 The Universal Night Answer (UNA) feature 
provides an output of interrupted ringing voltage 
(85 +10 VRMS, 20 Hz superimposed on -24 VDC) 
whenever the system is in Night Service and an 
incoming call is received by a trunk designated for 
UNA. Any station user, upon hearing the chime or 
bell, can dial the UNA access code and be con- 
nected to the caller. 
9.52 The ringing voltage output is intended to 
control a strategically located chime or loud ring- 
ing bell. The available power is five ringer equiva- 
lents. 
9.53 Two UNA zones can be installed in tenant 
systems. Either zone can be assigned in program- 
ming to either tenant. For PERCEPTION,, con- 
nections to the UNA ringing signal are via pins 12 
and 37 (0-BK, BK-0) of J2. This connection is to 
J502 in the expansion cabinet for UNAZone 1 (see 
Tables 5-4 and 5-10). UNA zone 1 requires a 
second NPRU PCB in the expansion cabinet. 
4-62  
						

							INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY1992 
P,-J2lJ502 
P,, -J 1 lJ2 
ZONE 1 
ZONE 2 
ZONE 3 
ZONE 4 
ZONE 5 
I I 
hi- I PGl 
I 
< 4 27 
! 
I i 
, PGGND 
I < +-z-- ‘-““--“-“--“-, i 
I 
I MUSIC AMP I 1 
OPTIONAL 
r-----1 
I ,““““““” 
r-4 I I 
,,,-,,---,----,I 
I I 
L-1 
I I CONNECTION 
NPRU MUSIC : FOR MUSIC 
SOURCE ; I i IN- 
; i PUT OUT- I i 
PUT: ! OVER EXTERNAL 
i SPEAKER 
1-j I----! 
L------l ,,,,,,-,,,,,,,I 
FlGURE4-70-PAGING WITH ONE AMPLIFIER 
9.54 UNA connections for PERCEPTION,, are 
made at pins 12 and 37 connectors Jl and 52 on 
the basic cabinet. A second UNA device requires a 
second NPRU to be installed in the basic cabinet. 
9.60 Station Message Detail Recording 
9.61 The Station Message Detail Recording 
(SMDR) feature enables a business to monitor and 
control its telephone costs. Data can be collected 
for each outgoing and/or incoming trunk call. Each 
such call generates a call record that is output at the 
SMDR connector on the connector panel at the upper rear of the LCEC-M or NCEC-M. (In Lodging/ 
Health Care applications, data specific to those 
applications are included in the SMDR output.) 
9.62 SMDR output can be connected to a variety of 
customer-provided equipment: 
l A local 80-column printer for an on-line printout 
at the termination of each trunk call. 
l A recording device to store data for subsequent 
processing, either on-site or by a service bureau. 
0 Call accounting equipment to provide custom- 
ized call reports. 
4-63  
						

							INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
NPRU 
-------------------. J2 
I 
I 
i PGGND 
i 
-----------,-,-I ZONE 2 
ZONE 3 
ZONE 4 
OPTIONAL CONNECTION 
FIGURE 4-71-PAGING WITH MULTIPLE AMPLIFIERS 
4-64  
						

							9.63 Refer to the external device manufacturer’s 
documentation for information on its SMDR con- 
nector pin assignments. 
9.64 The SMDR output speed can be set for either 
300 bps or 1200 bps by the MDR switch on the front 
panel of the LCCU PCB (Figure 4-72). SMDR pin 
assignments are as follows: 
FIGURE 4-72-LCCU SWITCHES 
9.70 The recording criteriaand account code length 
are defined in DMDR Program (see Section 200- 
255-300, Programming). 
1 5 1 Clear to Send (to SMDR device) 
I 
6 Data Set Ready 
7 Sianal Ground 
1 8 
I Carrier Detect 
I 20 I Data Terminal Readv (from SMDR device) 
I 
4-65 
9.65 The code used by SMDR is standard 7-level 
ASCII using one start bit, one stop bit and one parity 
bit (even parity). 
9.66 SMDR can be programmed to record data 
under any one of the following conditions: 
0 Incoming calls only. 
l Outgoing calls only. 
l Incoming and outgoing calls. 
l Outgoing toll calls only. 
l All incoming calls and outgoing toll calls. 9.71 Each time a trunk is seized, data is collected 
for that call until the trunk is released. This data is 
output at the SMDR port in thefollowingformat (see 
Figure 4-73). 
l Time 
l Start of Call Hour - tens - units 
Minute - tens - units 
l Call Duration Hour - units 
Minute - tens- units 
Seconds - tens - units 
l Condition Code (see table) 
A = Attendant handled 
D = Call > 10 hours 
E = Maintenance (SMDR port) 
F = Maintenance (trunk test) 
I = Incoming call 
K = Outgoing call 
L = Conference Attendant or 3-party 
M = Transfer or Call Forward 
N = 
SPCC #l 
0 = SPCC #2 
P = Date/Time change 
Q = System Initialize 
R = Incomplete call 
S = Date printed (every hour) 
l Access Code 3 digits maximum 
INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
JANUARY 1993 
9.67 When outgoing calls are chosen, all calls 
seizing a trunk will be recorded regardless of dura- 
tion. On incoming calls, all answered calls will be 
recorded. Calls disconnected by Toll or Code Re- 
striction features are not recorded. 
9.68 Timing for recorded calls will start as follows 
(Figure 4-73): 
l Outgoing-when trunk is seized. 
l Incoming to attendant only-when attendant 
answers. 
l Incoming and extended by the attendant-when 
attendant answers. 
l Incoming to a station-when answered. 
9.69 A station user can enter a charge account 
code of up to 12 digits for each call. This code is 
included in the SMDR output.  
						

							INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
JANUARY1993 
I 
1 2 3 4 5 6 7 6 9 101112131415161716192021222324252627282930313233343536373639404i424344454647484950515253545556575859606162636165666768697071 72 73 
/?/202:13310:00:25A~X9C001~1-516-669-1234/:201Iii002~123456789012~~ OUTGOING - -- -- START OF CALL CALLWRATlON CONDlTlON ACCESS TPN DIALEDPHONENUMBER STATION PGRT ACCOUNTCODE OR STROKE COUNT 
FIGURE 4-73-EXAMPLE: SMDR CALL RECORD 
l Dialed Number 15 digits maximum 
l Calling DN 4 digits maximum 
l Trunk Port 3 digits maximum 
l DNIS Digits 4 digits maximum 
l Calling Port No. 3 digits maximum 
l Account Code 12 digits maximum 
or 
l Stroke Count 4 digits maximum 
9.72 The format of the special record, for Initialize/ 
Reload and Time Change, is as follows: 
Initialize/Reload: 
NNNN etc. (previous records-usual call) 
00 (initialize or reload) 
9.73 Any record printed after the initialize record 
will appear on the same line and be offset three 
columns from the usual record. 
Example: 
NNNN (previous record) 
00 NNNNN (initialize and next record) 
NNNNNN 
Time Change: 
MM DD (old date) 
HH : MM (old time) 
MM DD (new date) 
HH : MM (new time) 9.74 Some complex calls will cause multiple call 
records (CR) for the same station or trunk. 
Examples: 
1) Station 1 transfers Trunk 1 to Station 2 
CR for Station 1 - Trunk 1 
= Condition Code I or K 
CR for Station 2 - Trunk 1 
= Condition Code M 
2) Station 1 transfers Trunk 1 to Trunk 2 
CR for Station 1 - Trunk 1 
= Condition Code I or K 
CR for Station 1 - Trunk 2 
= Condition Code L 
CR for Trunk 1 - Trunk 2 
= Condition Code M 
3) Station 1 holds Trunk 1 and calls Trunk 2 
CR for Station 1 - Trunk 1 
= Condition Code I or K 
CR for Station 1 - Trunk 2 
= Condition Code K 
9.75 All connections to miscellaneous equip- 
ment are made via J2, 
Jl, TTY, SMDR, and 
MODEM connectors on the connector panels 
of the system. 
4-66  
						

							9.80 Lodging/Health Care Data Audit 
9.81 The Lodging/Health Care Data Audit feature 
enables the user to record and analyze the registra- 
tion and operation of specific features in Lodging/ 
Health Care applications. 
9.82 Lodging/Health Care audit data is output at 
either the SMDR (as part of the SMDR printout) or 
the TTY (as a separate report) connector on the 
upper rear of the basic cabinet. (Because the TTY 
connector is required for on-site programming and 
maintenance procedures, it is recommended that 
the SMDR port be used.) The selection of data to be 
output and the connector choice (lTY or SMDR) are 
software-controlled (see DHMF Program in Sec- 
tion 200-255-300, Programming). 
9.83 The SMDR or TTY output can be connected 
to either: 
l A local 80-column printer for an on-line printout. 
l Compatible call accounting or property manage- 
ment interface equipment, supplied by another 
vendor. 
9.84 The audit pin-out assignments at the SMDR 
or the TTY connector are not identical. Refer to 
Paragraph 9.64for the pin-out assignments of each 
connector. For instruction on connecting equip- 
ment provided by other vendors, refer to the 
manufacturer’s documentation. 
9.85 The audit data output rate can be set for either 
300 bps or 1200 bps (depending on the configura- 
tion of the receiving equipment) at either the SMDR 
switch or the TTY switch on the front panel of the 
LCCU PCB. 
CAUTION! 
If the TTY connector is used for program- 
ming and maintenance operations, (either 
with an on-site teleprinter or remotely via a 
modem) be careful not to change 
the data 
rate setting of the 773’ switch so that it is 
incompatible with programming equip- 
men t. 
INSTALLATION INSTRUCTIONS 
SECTIONZOO-255-204 
FEBRUARY1992 
9.86 Figure 4-74 shows a typical Lodging/Health 
Care audit printout. Notes on the figure explain the 
possible value for each column. 
10. SYSTEM POWER UP 
10.00 General 
10.01 Upon initial power up, the system will 
automatically load its operating system and cus- 
tomer data from the disk. Two sets of disks are 
provided with each system; one set should always 
be mounted in the drive, the other kept as a spare. 
10.02 Activate the system as follows: 
1) Be sure the main power switch on the NPSA- 
M is in the OFF position, and plug the AC cord 
into the outlet. 
2) If the system uses D.02 or later version soft- 
ware, insert the SYSTEM disk in FDDO. If two 
drives are used, insert the MAINTENANCE 
disk (Figure 4-75) in FDDl . If the system uses 
D.O1 software, insert the program disk in FDDO. 
3) Turn the main power switch on the NPSA-M to 
the ON position. 
4) The floppy disk will run: LED will come on. 
l LCCU MAJ ALARM LED will be on. 
l NPRU PFT LED will be on. 
5) When loading is complete, the system will 
initialize and clear all LEDs. Only a true fault 
indication will remain. Refer to Section 200- 
255-500, Fault Finding Procedures, for 
meaning of indications and assistance with 
fault clearing. 
6) Refer to Section 200-255-300, Programming, 
to complete customer data assignments. 
4-67  
						

							INSTALLATION INSTRUCTIONS 
SECTION 200-255-204 
FEBRUARY 1992 
ROOM/DIRECTORY 
NUMBER 
FEATURE ’ 
OPERATION * 
TIME FEATURE WAS 
REGISTERED/ACTIVATED 
ROOM STATUS CODE 3 
TELEPHONE SET STATUS/AGENT 
REGISTERING OR CANCELLING FEATURE4 
NW AAzmma CANCEL 
LYL!VVd202nAWU~SETAAAAAAl5:11~0307660~M~15:1~~ q m 
NOTES: 
1. FEATURE 
MW = Message Waiting 
A WU = Automatic Wake-up 
MRA = Message Registration 
Audit 
Room Status = Room Status Audit 
2. OPERATION 4. This column shows either the status of 
the station accessed for feature opera- 
tion (for example, a wake-up call) or 
the agent who registered the feature. 
STATUS 
RNA = Ring No-Answer 
ON = Set at Attendant Console 
OFF = Cancelled at either Bsy = Busy 
$XxX.Xx = Total call charges for 
this station 
Attendant Console or 
Station 
SET = Set at either Attendant 
Console or Station 
CANCEL = Cancelled at either 
Attendant Console or 
Station M = Maid in Room 
XX:XX = Time Wake-up Call 
Scheduled for 
AGENT 
MC = Message Center 
EXT = Station 
3. ROOM STATUS CODE 
1 = Vacant and clean 
2 = Occupied and clean 
3 = Vacant and needs cleaning 
4 = Occupied and needs cleaning 
FIGURE 4-74-EXAMPLE: AUDIT PRINTOUT (LODGING/HEALTH CARE) 
4-68