Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

							PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
NOTES: 
TABLE 9-3 (continued) 
1. NN = trunk PCB number, X = circuit number 1 - 4 . 
2. Used only for PERCEPTIONex systems, for trunks assigned above T15. 
3. GG = trunk group number (00 - 15). 
MM = unique trunk number within group (00 - 63). 
15MM = Private Line 
or 
PVLMM = Private Line 
4. 
5. 
6. 
7. GMN cannot be changed. The Data Block must be removed (OUT) and NEW data must be 
entered. 
8. 
The characters available for trunk names are A - Z, 0 - 9, [space]. A maximum of 16 alphanumeric 
charaters are allowed for each name. for CO, FX, WATS trunks only. 
This prompt only appears for Trunk Group 15 (PVL). TDN is the DN assigned to a private trunk 
line (1 - 3 digits). 
Enter Trunk’s Night Directory Number (1 - 4 digits). This number can also be changed by the 
attendant when making night assignments (no meaning for TIuCCSA/DID/PVL trunks). This 
number must match the REM entry in the DSYS Program in order to activate Remote Access to 
Services. 
Enter Trunk’s Day Directory Number (1 - 4 digits). Up to 8 numbers may be entered, for either 
immediate or delayed ringing. Indicate delayed ringing for a specific station by entering i im- 
mediately after the station number. Day number(s) can also be changed by the attendant. 
The Attendant Console(s) CANNOTbe included as part of delayed ringing. i.e., lfA770 is entered 
at the DA Yprompt, no other entries are allowed. ACD pilot numbers also CANNOT be entered as 
part of delay ringing. i.e., If an ACD pilot number is entered at the DAY prompt, no other entries 
are allowed. 
9. If TEN = Yin the DSYS Data Block and trunks are assigned to TEN = 0 in DTGP, calls will ring only 
at Attendant 0; if the trunks are assigned to TEN = 1 in DTGP, calls will ring only at Attendant 1. 
If TEN = N in the DSYS Data Block, only ATO can be entered and calls will load share between 
ATT0 and ATT1 in a two-console operation. 
NONE = Calls will activate the UNA device. 
10. 
11. 
12. 
13. 
14. This entry assigns the destination of a Transfer Recall on this trunk. 
OPC = Originating Party Control. FPR = First Party Release. 
This prompt only appears for TlffCCSA/DID trunks. 
Outgoing dialing method: PlO = rotary dial 10 PPS. P20 = rotary dial 20 PPS. 
TON = DTMF. 
The OTR prompt appears only when a trunk is assigned to Trunk Group 15 (PVL). Following the 
OTR prom t, the system will prompt D and any entries made will be deleted. To add a station port, 
press the 
&I - key. The system will then prompt A and any entries made will be added. Each private 
line can have up to 96 line appearances, each of which can be individually restricted by using OTR. 
When programming these station ports, up to 10 ports may be entered in a single line. 
15. 
16. Is Answer Supervision required to the calling party? Y = yes; N = no. 
= Ignore line entered. 
Backspace. 
Stop printing and return to REQ. 
Exit Program. 
9-11  
						

							PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
TABLEg-3a 
TRUNKDATABLOCKENTRIES 
TRUNKTYPES 
COT 1 FEX 1 WAT 
PVL 1 DID ) CSA 1 TIE 
POR 
x I x I x xlxlxlx 
+-l-+-k 
UPN 
GMN 
TKID 
TDN 
RAD 
NIT 
DAY 
TRCL 
SIG 
DIS 
x I x I x 
CTL 0 I 0 I 0 
DIN 
0 0 0 0 x x X 
DOT X X X X X X X 
OTR 0 0 0 X 0 0 0 
ANS 0 0 0 0 x x X 
9-12  
						

							PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
TABLE 9-3(continued) 
Error Codes 
Error Code 1 Program Name: Trunk Group Data Block (DTRK) 
Meaning 
ERTRK 00 1 A PCB is not equipped in that location. 
ERTRK 01 
The PCB is not a trunk type. 
ERTRK 02 
The port is busy (REQ = OUT). 
ERTRK 03 1 The port has alreadv been assiqned to a station, DSS console, DDIU, or NDKU (REQ = NEW). 
1 
ERTRK 04 
This Trunk Group Data Block does not exist. 
ERTRK 05 Member number has already been assigned. 
ERTRK 06 1 The entry conflicts with an existinq DN or TDN. 
ERTRK 07 
The night number that was entered does not yet exist. 
ERTRK 09 
The type of signaling entered conflicts with the trunk type. 
ERTRK 11 
The input data was erased because the program was aborted during a NEW mode. 
ERTRK 12 
The port is not assigned. 
ERTRK 13 
Another type of data has already been assigned to the input port. 
ERTRK 15 
The entered DN has already been assigned to a station (electronic/digital or standard telephone). 
ERTRK 16 
The entered DN has already been assigned to another trunk. 
ERTRK 17 
The input DN is a DIU DN. 
ERTRK 19 I The DN Table is full. 
ERTRK 20 The Transfer Recall Termination DN does not exist. 
ERTRK 21 The input 
port has alreadv been entered. 
ERTRK 22 I The maximum number of ports (96) has already been registered for this PVL. 
I 
ERTRK 23 The entered port does not exist. 
ERTRK 24 The input 
port is not assiqned as a universal port. 
ERTRK 25 I The input universal port number has already been assiqned. 
ERTRK 27 The input data is not a DN. 
ERTRK 28 The input data has already been entered. 
ERTRK 29 The maximum number of DNs (8) has already been entered for this port. 
ERTRK 30 
The input data is AlTO, AlTl, UNA, or NONE. 
ERTRK 31 (REQ = OUT) The input port has already been assigned as a voice port (DSYS: ICP2). 
ERTRK 32 The Trunk ID is too long (maximum = 16). 
ERTRK 33 The Aqent ID number cannot be assianed. 
9-13  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-309 
FEBRUARY 1992 
ANS (Answer 
Supervision)-Determines 
whether or not answer supervision will be pro- 
vided to the distant trunk on incoming calls. (This 
prompt is for TIE, CCSA, and DID trunks only.) If 
“N” is entered, then the system will not return 
answer supervision. 
Enter: Y or N. 
4. Print Trunk Data Block (Table 9-4) WAT-All WATS Trunk Data Blocks will be output. 
4.01 To use the Print Trunk Data Block 
(PTRK 
Program): 
l Perform the Authorization Procedure (Level 1 or 
2). 
Enter: PTRK (in response to OK prompt). 
l When the REQ prompt is received after the 
program is loaded: 
Enter one of the following commands: 
PORALL-All Trunk Data Blocks will be output in 
order of Port Number (lowest first). 
PORNXX-Trunk Data Block of Port NNX will be 
output. 
PORVAC-All unassigned trunk ports will be listed. COT-All CO Trunk Data Blocks will be output. - 
FEX-All FX Trunk Data Blocks will be output. 
TIE-All TIE Trunk Data Blocks will be output. 
DID-All DID Trunk Data Blocks will be output. 
CSA-All CCSA Trunk Data Blocks will be output. 
-- 
PVL-All Private Line Trunk Data Blocks will be 
output. 
NIT-Night Station assignments for all CO/FX/ 
WATS trunks will be output. 
UPN-Universal Port Number assignments for 
trunks above T15 will be output. 
NOTES: 
1. The output format will be the same as that 
used for data input in the DTRK Program. 
2. OTR willprint for each trunk type, although 
it only has a meaning for PVL. 
TGPNN-All Trunk Data Blocks assigned to Trunk 
Group NN will be output. 
9-14  
						

							PROGRAMMINGPROCEDURES 
SECTlON200-255-309 
FEBRUARY1992 
TABLE 9-4 
Procedure - Print Trunk Data Block 
Authorization Procedure must be completed. If OK response is received, proceed as follows: 
ITEM PROMPT 
OK PTRK 
- DISK LOADING - USER ENTRY NOTE 
REQ 1 
- EXECUTE - 
REQ 1 
NOTES: 
1. The following responses are possible: 
PORALL = Outputs Trunk Data Blocks in numerical order of ports (lowest first). 
PORNNX = Outputs Trunk Data Block of Port NNX. 
PORVAC = Outputs all unassigned trunk pot-is. 
TGPNN = Outputs all Trunk Data Blocks assigned to trunk group NN. 
COT = Outputs all CO Trunk Data Blocks. 
FEX = Outputs all FX Trunk Data Blocks. 
WAT = Outputs all WATS Trunk Data Blocks. 
TIE = Outputs all TIE Trunk Data Blocks. 
DID = Outputs all DID Trunk Data Blocks. 
CSA = Outputs all CCSA Trunk Data Blocks. 
PVL = Outputs all PVL Trunk Data Blocks. 
NIT = Outputs the Night Station Assignments for all CO, FX, and WATS trunks. 
UPN = Outputs the Universal Port Number Assignments for trunks above T15. 
Ignore line entered. 
Backspace. 
Stop printing and return to REQ. 
Exit program. 
Error Codes 
Program Name: Print Trunk Data Block IPTRK) 
Error Code 
ERPTR 00 Invalid response. Meaning 
ERPTR 01 The PCB number or circuit number is out of range (REQ = PORNNX). 
ERPTR 02 The input trunk group is out of range (REQ = TGPNN). 
1 ERPTR 03 1 The inDut ~ort is not assianed to a trunk (REQ = PORVAC). 
9-15  
						

							PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
5. Station Message Detail Recording Data Block 
(Table 9-5) 
5.01 The Station Message Detail Recording Data 
Block (DMDR Program) defines the account code 
length and type of calls to be recorded for each 
trunk group for the SMDR feature. Data is entered 
as follows: 
REQ (Request)-Indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data Block. 
CHG-To alter an existing Data Block. 
OUT-To delete an existing Data Block. 
TPN (Trunk Port Number)-Allows Trunk Port 
Numbers to be printed in the SMDR report. 
Enter: Y to allow; N to deny. 
ACL (Account Code Length)--Defines the length 
of the account code that is to be used or indicates 
that no account code is to be used. 
Enter: Number of digits to be used (1 - 12) or 
NONE. 
NOTE: 
The account code length must be programmed 
in order for the account code features (Volun- 
tary, Verified and Forced) to be enabled. 
SPCCI (Specialized Common Carrier #l )-In- 
forms the system of the DN that is used to access 
an SPCC (MCI, Sprint, etc.). The system will 
recognize the DN and enter a unique condition 
code in the SMDR output. 
Enter: SPCC Number NXXXXXX or 
Equal Access Number 1 OXXX or NONE. SPCC2 (Specialized Common Carrier &+-Same 
as SPCCI , but for a second carrier. 
Enter: SPCC Number NXXXXXX or 
Equal Access Number 1 OXXXor NONE. 
NOTE: 
Data that is entered here will also appear at 
the SPCCI and SPCC2 entries in the DTOL 
Data Block. SPCCI and SPCC2 entries..will 
not appear in the SMDR output. 
TGP (Trunk Group)-Defines the type of calls to 
be recorded by SMDR for a given trunk group. 
Enter: XX YYY. 
(XX = Trunk group number.) 
(YYY = INC-Incoming only 
OGT-Outgoing only 
IAO-Incoming and outgoing 
TOL-Toll calls only 
INT-Incoming-all; Outgoing-toll only 
NONE-No records.) 
Repeat for each trunk group that is used 
in the system. 
NOTE: 
A call made by using an SPCC is not treated 
as a toll call for SMDR purposes. 
9-16  
						

							PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
TABLE 9-5 
Procedure - Station Message Detail Recording (SMDR) Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM 
PROMPT USER ENTRY NOTE 
OK 
DMDR 
- DISK LOADING - 
I I REQ 1 NEW, CHG, OUT 
I 
Trunk Port Number 
TPN 
Account Code Length ACL 
Y or N 
1 - 12 or NONE 1 
I Special Common Carrier #l DN 
I SPCCl 
I NXXXXXX or 10XxX or NONE 1 2 
Special Common Carrier #2 DN 
Trunk Group 
SPCC2 
TGP NXXXXXX or 10XxX or NONE 2 
xx YYY 3 
I TGP I 
NOTES: 
1. Y = Trunk Port Number will be printed in the SMDR report. 
N = Trunk Port Number will not be printed. 
2. SPCC I & 2 entries are the DN of any Specialized Common Carrier (SPCC) used (MCI, Sprint, etc.) 
or Equal Access Number (10XxX). Data entered here will also appear in the PAR table in Toll 
Restriction (DTOL). (Data that is entered here will not appear in the SMDR output.) 
3. Enter the trunkgroup number (XX) and the type of calls (YYY) to be recorded on this Trunk Group: 
INC = 
OGT = 
IA0 = 
TOL = 
INT = 
NONE = Incoming only. 
Outgoing. 
Incoming and outgoing. 
Toll only. 
Incoming -All. 
Outgoing - Toll only. 
No records. 
4. TGP continues to be prompted untilm is entered. 
= Ignore line entered. 
Backspace. 
Stop printing and return to REQ. 
Exit program. 
Error Codes 
Program Name: SMDR Data Block (DMDR) 
Error Code 
ERMDR 00 
ERMDR 01 
Meaning 
SMDR customer data already exists (REQ = NEW). 
SMDR customer data does not exist (REQ = CHG, OUT). 
ERMDR 02 
I The account code length cannot be changed if verifiable 
account codes are programmed. 
I 
9-17  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-309 
FEBRUARY 1992 
6. Print Station Message Detail Recording Data 
Block (Table 9-6) 
6.01 To use the Print SMDR Data Block (PMDR 
Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3): 
Enter: PMDR (in response to the OK prompt). 
l When an REQ response is received after the 
program is loaded: 
Enter: PRT. 
l The SMDR Data Block will be printed out in the 
following format: 
REQ PRT 
ACL 
xx (01 12) 
SPCCl NXXXXXX or 1 OXXX SPCC2 NXXXXXX or 1 OXXX 
TGP xx xxx 
TGP xx xxx 
etc. 
l The REQ prompt will be given when the printout 
is complete. 
Enter: mm 
q (to exit the program). 
7. Dialed Number Identification Service Data 
Block (Table 9-7) 
7.01 The Dialed Number Identification Service 
(DNIS) Data Block (DDNI Program) is used to 
program DNIS numbers, destinations, and alpha- 
numeric displays. The system refers to this data 
block for routing and other handling instructions for 
TABLE 9-6 
Procedure - Print Station Message Detail Recording (SMDR) 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
I ITEM PROMPT USER ENTRY NOTE 
OK PMDR 
- DISK LOADING - 
I =Q 1 
I - EXECUTE - 
I REQ 1 
NOTES: 
1. The only response possible is: PRT = Outputs SMDR Data Block. 
Ignore line entered. 
Backspace. 
Stop printing and return to REQ. 
Exit program. 
9-18  
						

							calls received via a port assigned to a DNIS trunk 
group. 
REQ (Request)-Indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data Block. 
CHG-To alter an existing Data Block. 
OUT-To delete an existing Data Block. 
TAB (DNIS Table Number)-Identifies the DNIS 
Table. The system can support a maximum of 
125 DNIS tables. 
Enter: 1 - 125. 
NUM (Number of Digits Received)-identifies the 
number of digits sent by the CO. 
Enter: 1 - 5. 
PROGRAMMING PROCEDURES 
SECTION 200-255-309 
FEBRUARY 1992 
DIG (Actual Digits Received)-Identifies the ac- 
tual DTMF/DP digits received from CO. 
Enter: XXXXX (1 - 5 digits). 
DN (Destination Directory Number)-Routing 
destination for DNIS trunk. This can be an inter- 
nal directory number, an ACD Group pilot number, 
a Master Distributed Hunting Group pilot number, 
a voice mail port, the attendant console (UNA in 
Night Service), or UNA in either Day or Night 
Service. 
Enter: XXXX (1 - 4 digits) or NONE (UNA). 
NOTES: 
1. When TEN = N in the DSYS Program, 
programming A TTO or A TTI with two con- 
soles causes a load share condition. 
TABLE 9-7 
Procedure - Dialed Number Identification Service Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT 
USER ENTRY NOTE 
I OK 1 DDNI 
- DISK LOADING - 
I REQ 
I NEW, CHG, OUT 
I I 
DNIS Table Number 
Number of Digits Received 
Actual Digits Received 
Destination Directory Number TAB 
NOM 
DIG 
DN l-125 
1-5 
xxxxx 
1 - 4 digits 
Alphanumeric Display 
I DIS 
I ~ 16 characters --~l--il 
NOTES: 
1. A maximum of 125 DNIS tables is possible. 
2. Number of digits sent by CO. 
3. Actual DTMF/DP digits received from CO. 
4. Routing destination for DNIS trunk. This can be an internal directory number, an ACD Group pilot 
number, a Master Distributed Hunting Group pilot number, a voice mailport, the attendant console 
(UNA in Night Service), or UNA in either Day or Night service. 
5. Alphanumeric characters to be displayed. If different digits (DIG) were received for different calls, 
and the calls were routed to the same Destination Directory Number (DN), a different message can 
be displayed for each call. (A - Z, 0 - 9 allowed and SPACE/BLANK.). 
-- 
= Ignore line entered 
= Backspace. 
= 
Stop printing and return to REQ. 
= Exit program. 
9-19  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-309 
FEBRUARY 1992 
TABLE 9-7 (continued) 
Error Codes 
I Program Name: Dialed Number Identification Service Data Block (DDNI) 
I 
1 Error Code 1 Meaning 
I 
ERDNI 00 
ERDNI 01 The data is already assigned (REQ=NEW). 
The number of “DIG” is different from “NUM.” 
I ERDNI 02 
I Input DIG data has already been assigned. 
I 
ERDNI 03 
ERDNI 04 
ERDNI 05 Input DN or table is not assigned. 
The input data was erased because the program was aborted during a NEW data entry. 
There is an inappropriate character. 
ERDNI 06 Input DN cannot be assigned for the destination DN. 
I 
2. When TEN = Y, the programming of TEN 
= 
0 or 1 in the DTGP Program controls 
which console calls route to. Tenant ser- 
vice does not load share. 
DIS (Alphanumeric Display)--Defines the al- 
phanumeric characters to be displayed. 
Enter: Maximum of 16 characters. 
or 
None (LCD display will show trunk #I.) 
8. Print Dialed Number Identification Service 
Data Block (Table 9-8) 
8.01 To use the Print Dialed Number Identification Service Data Block (PDNI Program): 
l Perform the Authorization Procedure (Level 1 or 
2). 
Enter: PDNI (in response to the OK prompt). 
l When the REQ prompt is received after the 
program is loaded: 
Enter one of the following commands: 
TBL ALL-All DNIS Data Blocks will be out- ::.-r-, 
put. 
‘. ” 
NUM X-All X (X = 1 - 5) Digit Data Blocks 
will be output. 
TABLE 9-8 
Procedure - Print Dialed Number Identification Service Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
I ITEM PROMPT 
USER ENTRY NOTE 
I 
OK 1 PDNI I I 
- DISK LOADING - 
=Q TBL ALL, NUM X 1 
NOTE: 
The following responses are possible: 
Tl3L ALL = All DNIS Data Blocks will be output. 
NUM X = All X (X = 1 - 5) Digit Data Blocks will be output. 
9-20