Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

							CHAPTER 13 
LODGING/HEALTH CARE DATA 
1. Lodging/Health Care Features Data Block 
(Table 13-l) 
1 .Ol 
The Lodging/Health Care Features Data Block 
(DHMF Program) defines the number of miscella- 
neous parameters that pertain to the Lodging/ 
Health Care features. Data is entered as follows: 
NOTE: 
Be sure to run the DMYC program (Back-up 
Memory Check Entry Procedure) when the 
system is put into the Lodging/Health Care 
mode of operation, and before this program is 
entered, 
REQ (Request)-Indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data Block. 
CHGTo alter an existing Data Block. 
OUT-To delete an existing Data Block. 
NOTE: 
If OUT is entered, all entries will be set to 
“NONE. ” 
PROGRAMMING PROCEDURES 
SECTION 200-255-313 
FEBRUARY 1992 
AWU SRC (Automatic Wake-up Source)- 
identifies the source that the called party will 
hear after the wake-up call has been answered. 
Enter: MOH-Music-on-Hold. 
VCE-Preprogrammed digitized voice 
announcement. 
NONE-Silence. 
AWU POR (Automatic Wake-up)-Identifies the 
output port that the system will use to send 
automatic wake-up verification information. 
Enter: SMDR, TTY, or NONE. 
MW POR 
(Message Waiting)-Identifies the out- 
put port that the system will use to send message 
waiting verification information. 
Enter: SMDR, TTY, or NONE. 
MR POR 
(Message Registration)-Identifies the 
output port that the system will use to send 
message registration information. 
Enter: SMDR, TTY, or NONE. 
RMS 
(Room Status Audit)-Identifies the output 
pot-tthat the system will use to send Room Status 
Audit information. 
Enter: SMDR, -TTY, or NONE. 
13-1  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-313 
FEBRUARY 1992 
TABLE 13-I 
Procedure - Lodging/Health Care Features Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT 
USER ENTRY NOTE 
OK DHMF 
- DISK LOADING - 
REQ NEW, CHG, OUT 1 
Automatic Wake-up Source 
AWU SRC MOH, VCE, or NONE (NONE) 2 
Automatic Wake-up 
AWU POR SMDR, TTY, or NONE (NONE) 
Message Waiting 
MW POR SMDR, TTY, or NONE (NONE) 
Message Registration 
MR POR SMDR, TTY, or NONE (NONE) 
Room Status Audit 
RMS SMDR, lTY, or NONE (NONE) 
Default values are noted in parentheses ( ). 
NOTES: 
1. “OUT” sets all entries to “NONE. ” 
2. MOH = Music-on-Hold source. 
Preprogrammed digitized voice announcement. 
Ignore line entered. 
Backspace. 
Stop printing and return to REQ. 
Exit program. 
Error Codes 
I Program Name: Lodging/Health Care Features Data Block (DHMF) 
1 Error Code 1 Meanina 
ERHMF 00 The input data was erased because the program was aborted during a NEW entry. 
ERHMF 01 The input DN conflicts with an existing DN. 
13-2  
						

							PROGRAMMINGPROCEDURES 
SECTION 200-255-313 
FEBRUARY1992 
2. Print Lodging/Health Care Features Data 
Block (Table 13-2) 
l When an REQ prompt is received after the pro- 
gram is loaded: 
Enter: PRT. 
2.01 To use the Print Lodging/Health Care Fea- 
tures Data Block 
(PHMF Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
l The Lodging/Health Care Features Data Block 
will be output, with features listed in the order that 
they were input in the 
DHMF Program. 
Enter: PHMF (in response to the OK prompt). 
TABLE13-2 .,.- 
Procedure - Print Lodging/Health Care Features Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT USER ENTRY NOTE 
OK PHMF 
- DISK LOADING - 
REQ PRT 1 
I 
- EXECUTE - 
REO I 1 
NOTES: 
response possible is: PRT = Outputs Lodging/Health Care Features Data Block. 
= Ignore line entered. 
= Backspace. 
= Stop printing and return to REQ. 
= Exit program. 
13-3  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-313 
FEBRUARY 1992 
3. Message Registration Data Block (Table 
13-3) 
3.01 TheMessage Registration DataBlock(DMRD 
Program) defines all parameters for the Message 
Registration feature. 
REQ (Request)-Indicates that the program has 
loaded. Two responses are possible: 
CHG-To change an existing Data Block. 
OUT-To delete an existing Data Block. 
ICC (Interchangeable Codes)-A “Y” informs the 
system that interchangeable codes are ,used. 
These are office codes that have 0 or 1 as the 
second digit (NO/i X format). Area codes will be 
identified as the three digits following the DDD 
prefix. Office codes will be identified as the first 
three digits when a DDD prefix is not dialed (see 
DDP prompt). 
Enter: Y or N. 
DDP (Direct Distance Dialing Prefix)-Defines the 
Direct Distance Dialing (DDD) prefix in the Num- 
bering Plan Area (NPA). If ICC is “Y,” then NO/l X 
and NXX become interchangeable, enabling area 
codes and office codes to have 0 or 1 as their 
second digit. In this case, the DDP is used to 
differentiate between the two code types (see 
example). If the ICC response is “N”, then calls 
will be made using the normal NPA formula of 
NO/lx and NNX. 
Enter: 1, 2, or 3 digits or NONE. 
Example: If ICC is “Y” and the DDP is pro- 
grammed as 1, then the dialed num- 
ber 209-1234 is recognized as a call 
within the home area code, while the 
dialed number 1-209-555-l 234 is 
recognized as acall outside the home 
area code. If ICC is “N”, this dialing 
plan is not used. 
HAC (Home Area Code)-Defines the area code 
in which the system is operating. A home area 
code is also used to analyze dialed numbers 
which do not contain an area code. Data entered 
here will appear in theToll Restriction Data Block 
(DTOL Program, PAR table, HAC prompt). 
Enter: Area Code (NO/l X). SVT (Supervision Time)-Defines the time al- 
lowed for a call to be connected before the First 
Billing Interval begins. This timer will start when 
the system accesses a trunk during an outgoing 
local call. 
Enter: 0 - 120 (time in seconds). 
TNl-TN5 (Rate Tables 1 - 5)-These prompts 
require no user entry. They wiil be followed by 
prompts which request parameters for the op- 
eration of the Message Registration features. 
FBI (First Billing Interval)-Defines the interval 
time for the first billing interval. 
Enter: 1 - 180 (time in seconds). 
FBU (First Billing Unit)-Defines the number of 
billing units per first billing interval. 
Enter: 0 - 100. 
IBI (Incremental Billing Interval)-Defines the 
interval time for each incremental billing interval. 
Enter: 1 - 180 (time in seconds). 
IBU (Incremental Billing Units)-Defines the 
number of billing units per incremental billing 
interval. 
Enter: 0 - 100. 
CST (Unit Cost)-Defines the cost per each billing 
unit. 
Enter: 1 - 500 (cost in cents). 
OCA (Office Codes-Add)-Indicates the office 
codes that are to be added to the office code 
table and defines the calls that are to be billed 
according to one of the five Rate Tables. Office 
codes may be added either by using single 3- 
digit codes or by using 4-digit range codes. 
Enter: NXXX NXX NXXX etc. 
OCD (Off ice Codes-Delete)-indicates the off ice 
codes that are to be deleted from the office code 
table. Office codes may be deleted either by 
using single 3-digit codes or by using 4-digit 
range codes. 
Enter: NXXX NXX NXXX etc. 
NOTE: 
N=2-9, X=0-9. 
13-4  
						

							PROGRAMMINGPROCEDURES 
SECTION 200-255-313 
FEBRUARY1992 
RANGES EXAMPLE: 
4-digit Format Off ice Codes 
2209 220-229 
2316 231 -236 
2478 247-248 
TABLE13-3 
Procedure 
- Message Registration Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT USER ENTRY NOTE 
OK DMRD 
- DISK LOADING - 
=Q 1 CHG; OUT 
I I 
interchangeable Code? ICC 1 Y or N (N) 
I 
1 1 - 3 digits or NONE (NONE) 
! 
DDD Prefix DDP 
! 1 NO/lx (NONE) 
! 
Home Area Code HAC 1 
Supervision Time SVT 1 0 - 120 (time in seconds) (NONE) 
Rate Table #l TN1 2 
First Billing interval 
FBI 1 - 180 (time in seconds) (NONE) 
First Billing Unit FBU 
1 0 - 100 (NONE) 
Incremental Billing Interval 
! IBI 1 1 - 180 (time in seconds) (NONE) 
Incremental Billing Units IBU 
1 0 - 100 (NONE) 
Unit Cost 
CST 1 - 500 (cost in cents) (NONE) 
Off ice Codes - Add 
OCA NXX or NXXX 3 
Off ice Codes - Delete 
I OCD 
I NXX or NXXX I 3&4 
Default values are noted in parentheses 0. 
(con timed, 
NOTES: 
1. N=2-9,X=0-9. 
2. This Rate Table will be followed by four other Rate Tables with the same prompts (FBI - OCD). 
3. A maximum of 800 3-digit numbers (in the format NXX[N = 2 - 9, X = 0 - 91) is permitted. Ranges 
are possible (7309 = 730 - 739). 
4. Rate Table 5 contains all office codes. As office codes are added to any Rate Table 1 - 4, they 
are automatically deleted from Rate Table 5. If an office code is deleted from any Rate Table 1 
- 4, it is automatically returned to Rate Table 5. 
Ignore line entered. 
Stop printing and return to REQ. 
13-5  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-313 
FEBRUARY 1992 
TABLE13-3(continued) 
Error Codes 
Error Code 
ERMRD 00 
ERMRD 01 Program Name: Message Registration Data Block (DMRD) 
Meaning 
Numeric error (0 - 9). 
Area Code (NO/IX) is out of range (N = 2 - 9, X = 0 - 9). 
ERMRD 02 Supervision Time is out of range (0 - 120). 
ERMRD 03 Billing Interval is out of range (1 - 180). 
ERMRD 04 Billing Unit is beyond time (0 - 100). 
ERMRD 05 Unit Cost is bevond limit (1 - 500). 
ERMRD 06 
ERMRD 07 
ERMRD 08 Office Code (NXX) is out of range (N = 2 - 9, X = 0 - 9). 
The number of Office Codes exceeds the maximum (800). 
The input data was erased because the program was aborted during a NEW entry. 
ERMRD 10 1 MRD data does not exist (REQ = CHG, OUT). 
13-6  
						

							4. Print Message Registration Data Block(Table 
13-4) 
4.01 To use the Message Registration Data Block 
(PMRD Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
Enter: PMRD (in response to the OK prompt). 
l When an REQ prompt is received after the pro- 
gram is loaded: 
Enter: One of the following commands: 
MRDALL-Ail Message Registration Data will be 
output. There may be a delay in the output after 
the OCA prompt. 
PROGRAMMINGPROCEDURES 
SECTION 200-255-313 
FEBRUARY1992 
MRDPAR-The system will output a partial list of 
the Message Registration Data Block (ICC, DDP, 
HAC, and S/T). 
RTNPAR-The system will output a partial list of 
the Message Registration Data Block (FBI, FBU, 
IBI, IBU, and CST for Rate Tables 1 - 5). 
RTNALL-The system will output all the data from 
the Rate Tables 1 - 5 (FBI, FBU, IBI, IBU, CST, 
and OCA). There may be a delay in the output 
after the OCA prompt. 
TABLE.13-4 
Procedure - Print Message Registration Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT 
OK PMRD USER ENTRY NOTE 
- DISK LOADING - 
REQ 1 
- EXECUTE - 
I I =Q I 1. I 
NOTES: 
1. The following responses are possible: 
MRDALL =- 
MRDPAR = 
RTNPAR = 
RTNALL = Outputs all Message Registration Data. There may be a delay in the output after the 
OCA prompt. 
Outputs a partial list of the Message Registration Data Block (ICC, DDP, HAC, and 
SW,). 
Outputs a partiallist of the Message Registration Data Block(FBI, FBU, IBI, IBU, and 
CST for Rate Tables 1 - 5). 
Outputs all the data from Rate Tables 1 - 5 (FBI, FBLJ, IBI, IBU, CST, and OCA). 
There may be a delay in the output after the OCA prompt. 
Ignore line entered. 
Backspace. 
Stop printing and return to REQ. 
Exit program. 
13-7  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-314 
FEBRUARY 1992 
CHAPTER 14 
SPEED DIAL LIST DATA 
1. Speed Dial List Data Block (Table 14-I) 
1.01 The Speed Dial List Data Block (DSDL Pro- 
gram) contains all numbers stored on the 90- 
number Speed Dial - System list and the 50 lo- 
number Speed Dial - Station lists. 
1.02 The DSDL Program allows initial storage or 
changes to any speed dial list from the mainte- 
nance terminal. Data is entered as follows: 
REQ (Request)--Indicates that the program has 
loaded. Two responses are possible: 
CHG-To alter an existing or to enter a new 
Data Block. 
OUT-To delete an existing Data Block. 
LNO (List Number)-The number of the list to be 
changed or deleted. 
Enter: 00 (for System List) or 
01 - 50 (for Station List). STR 
(Store Number)-This prompt requests the 
number to be stored. 
Enter: Address code, space, and number in the 
following format: 
Example: 0 9*NPANNXXXXX 
1 9*NPANNXXXXX 
NOTE: 
In these examples, 9 is a trunk access code. 
Therefore, a “““is entered to cause a 3-second 
pause for dial tone delay. The “*“is counted as 
one of the 16 allowable digits. 
NOTE:’ 
If the OUTcommand was entered in response 
to REQ above, then no other data is required. 
14-l  
						

							PROGRAMMING PROCEDURES 
SECTION 200-255-314 
FEBRUARY 1992 
TABLE 14-l 
Procedure - Speed Dial List Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows. 
ITEM PROMPT 
USER ENTRY NOTE 
OK DSDL 
- DISK LOADING - 
I RN 
I List Number 
I LNO 
I Store Number 
I STR 
STR 
I I RR0 
CHG, OUT 
0 9’ NPANN XXXXX 
I 2&3 
19’ NPANN XXXXX I 
2 9* NPANN XXXXX 
ma! 
Repeat program, if necessary. 4 
NOTES: 
1. XX = List number. 
00 = System List (90 numbers maximum: 10 - 99). 
01 - 50 = Station Lists (10 numbers each maximum: 0 - 9). 
2. Input procedure is: Address Code + [space] + Access Code + Pause + DN. For example: 1 
9*NPANNXXXX. 
3. Stored numbers may be any length between 1 and 16 digits; * enters a 3second pause and is 
counted as one of the 16 diaits. 
4. No further prompt will be &en until= is entered. 
ii = Ignore line entered. 
= Backspace. 
= Stop printing and return to REQ. 
m = Exit program. , 
Error Codes 
Error Code Program Name: Standard Telephone Data Block (DSTT) 
Meaning 
ERSDL 00 
The input list number is out of range (0 - 50 are allowed). 
I 
ERSDL 01 
ERSDL 02 The address code of the system list is out or range (10 - 99 are allowed). 
The address code of the station list is out of range (0 - 9 are allowed). 
ERSDL 03 
I Invalid DN (1 - 16 digits are allowed). 
14-2  
						

							2. Print Speed Dial List Data Block (Table 14-2) 
2.01 To use the Print Speed Dial List Data Block 
(PSDL Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
Enter: PSDL (in response to the OK prompt). 
l When the REQ prompt is received after the 
program is loaded: 
Enter one of the following commands: 
ALL-All of the Speed Dial lists will be output. 
SYST-System Speed Dial list will be output. 
LSTXX-Station Speed Dial list XX will be output. 
PROGRAMMINGPROCEDURES 
SECTION 200-255-314 
FEBRUARY1992 
NOTE: 
There are 50 Station Speed Dial Lists (LSTOI 
- LST50), each of which may have up to ten 
numbers (0 - 9). 
The output format is as follows: 
REQ LSTOG 
LNO 06 
SDC LOO2 
SDU LO03 LO10 
STR 00 9*7147305000 
01 9*9142731750 
02 NONE 
03 ‘( 
09 rr 
TABLE14-2 
Procedure - Print Speed Dial List Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT 
OK PSDL USER ENTRY NOTE 
- DISK LOADING - 
REQ 1 
- EXECUTE - 
I I REQ I 1. 
NOTES: 
1. The following responses are possible: 
ALL = 
SYST = 
LSTXX = 
2. - = 
. 
c a = 
: m: 
Outputs all Speed Dial List Data Blocks. 
Outputs System Speed Dial List Data Block. 
Outputs Station Speed Dial List XX Data Blocks. 
Ignore line entered. 
Backspace. 
Stop printing 
and return to REQ. 
Exit program. 
Error Codes 
Error Code 
ERPST 00 Program Name: Print Speed Dial List (PSDL) 
Meaning 
The list number is out of ranae (0 - 50 is available).