Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
NOTES: 
TABLE 9-3 (continued) 
1. NN = trunk PCB number, X = circuit number 1 - 4 . 
2. Used only for PERCEPTIONex systems, for trunks assigned above T15. 
3. GG = trunk group number (00 - 15). 
MM = unique trunk number within group (00 - 63). 
15MM = Private Line 
or 
PVLMM = Private Line 
4. 
5. 
6. 
7. GMN cannot be changed. The Data Block must be removed (OUT) and NEW data must be 
entered. 
8. 
The characters available for trunk names are A -...

PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
TABLEg-3a 
TRUNKDATABLOCKENTRIES 
TRUNKTYPES 
COT 1 FEX 1 WAT 
PVL 1 DID ) CSA 1 TIE 
POR 
x I x I x xlxlxlx 
+-l-+-k 
UPN 
GMN 
TKID 
TDN 
RAD 
NIT 
DAY 
TRCL 
SIG 
DIS 
x I x I x 
CTL 0 I 0 I 0 
DIN 
0 0 0 0 x x X 
DOT X X X X X X X 
OTR 0 0 0 X 0 0 0 
ANS 0 0 0 0 x x X 
9-12  

PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
TABLE 9-3(continued) 
Error Codes 
Error Code 1 Program Name: Trunk Group Data Block (DTRK) 
Meaning 
ERTRK 00 1 A PCB is not equipped in that location. 
ERTRK 01 
The PCB is not a trunk type. 
ERTRK 02 
The port is busy (REQ = OUT). 
ERTRK 03 1 The port has alreadv been assiqned to a station, DSS console, DDIU, or NDKU (REQ = NEW). 
1 
ERTRK 04 
This Trunk Group Data Block does not exist. 
ERTRK 05 Member number has already been assigned. 
ERTRK...

PROGRAMMING PROCEDURES 
SECTION 200-255-309 
FEBRUARY 1992 
ANS (Answer 
Supervision)-Determines 
whether or not answer supervision will be pro- 
vided to the distant trunk on incoming calls. (This 
prompt is for TIE, CCSA, and DID trunks only.) If 
“N” is entered, then the system will not return 
answer supervision. 
Enter: Y or N. 
4. Print Trunk Data Block (Table 9-4) WAT-All WATS Trunk Data Blocks will be output. 
4.01 To use the Print Trunk Data Block 
(PTRK 
Program): 
l Perform the Authorization...

PROGRAMMINGPROCEDURES 
SECTlON200-255-309 
FEBRUARY1992 
TABLE 9-4 
Procedure - Print Trunk Data Block 
Authorization Procedure must be completed. If OK response is received, proceed as follows: 
ITEM PROMPT 
OK PTRK 
- DISK LOADING - USER ENTRY NOTE 
REQ 1 
- EXECUTE - 
REQ 1 
NOTES: 
1. The following responses are possible: 
PORALL = Outputs Trunk Data Blocks in numerical order of ports (lowest first). 
PORNNX = Outputs Trunk Data Block of Port NNX. 
PORVAC = Outputs all unassigned trunk pot-is. 
TGPNN...

PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
5. Station Message Detail Recording Data Block 
(Table 9-5) 
5.01 The Station Message Detail Recording Data 
Block (DMDR Program) defines the account code 
length and type of calls to be recorded for each 
trunk group for the SMDR feature. Data is entered 
as follows: 
REQ (Request)-Indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data Block. 
CHG-To alter an existing Data Block. 
OUT-To delete an existing...

PROGRAMMINGPROCEDURES 
SECTION 200-255-309 
FEBRUARY1992 
TABLE 9-5 
Procedure - Station Message Detail Recording (SMDR) Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM 
PROMPT USER ENTRY NOTE 
OK 
DMDR 
- DISK LOADING - 
I I REQ 1 NEW, CHG, OUT 
I 
Trunk Port Number 
TPN 
Account Code Length ACL 
Y or N 
1 - 12 or NONE 1 
I Special Common Carrier #l DN 
I SPCCl 
I NXXXXXX or 10XxX or NONE 1 2 
Special Common Carrier #2 DN 
Trunk Group...

PROGRAMMING PROCEDURES 
SECTION 200-255-309 
FEBRUARY 1992 
6. Print Station Message Detail Recording Data 
Block (Table 9-6) 
6.01 To use the Print SMDR Data Block (PMDR 
Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3): 
Enter: PMDR (in response to the OK prompt). 
l When an REQ response is received after the 
program is loaded: 
Enter: PRT. 
l The SMDR Data Block will be printed out in the 
following format: 
REQ PRT 
ACL 
xx (01 12) 
SPCCl NXXXXXX or 1 OXXX SPCC2 NXXXXXX or 1 OXXX...

calls received via a port assigned to a DNIS trunk 
group. 
REQ (Request)-Indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data Block. 
CHG-To alter an existing Data Block. 
OUT-To delete an existing Data Block. 
TAB (DNIS Table Number)-Identifies the DNIS 
Table. The system can support a maximum of 
125 DNIS tables. 
Enter: 1 - 125. 
NUM (Number of Digits Received)-identifies the 
number of digits sent by the CO. 
Enter: 1 - 5. 
PROGRAMMING PROCEDURES 
SECTION...

PROGRAMMING PROCEDURES 
SECTION 200-255-309 
FEBRUARY 1992 
TABLE 9-7 (continued) 
Error Codes 
I Program Name: Dialed Number Identification Service Data Block (DDNI) 
I 
1 Error Code 1 Meaning 
I 
ERDNI 00 
ERDNI 01 The data is already assigned (REQ=NEW). 
The number of “DIG” is different from “NUM.” 
I ERDNI 02 
I Input DIG data has already been assigned. 
I 
ERDNI 03 
ERDNI 04 
ERDNI 05 Input DN or table is not assigned. 
The input data was erased because the program was aborted during a NEW data...