Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

PROGRAMMING PROCEDURES 
SECTION 200-255-306 
FEBRUARY 1992 
TABLE 6-la (continued) 
FEATURE ABB. 
I STD. CODE 
Room Status - Status 1 Set (Vacant/Clean) 
I RSSl I %l 
Room Status - Status 2 Set (Occuoied/CleanI I 
RSS2 I “#2 
Room Status - Status 3 Set (Vacant/Needs Cleaning) 
RSS3 *#3 
Room Status - Status 4 Set (Occupied/Needs Cleaning) 
Room Status Set From 2 to 4 
RSS4 *#4 
RS24 *#5 
Room Status Set From 4 to 2 I RS42 I *#6 
Display Deposit Paid 
Set Deposit Paid 
Clear Deposit Paid 
Voice Message...

PROGRAMMINGPROCEDURES 
SECTION 200-255-306 
FEBRUARY1992 
2. Print Access Code Data Block (Table 6-2) 
2.01 To use the Print Access Code Data Block 
(PACD Program): 
l Perform the Authorization Procedure (Level 1 or 
a 
Enter: PACD (in response to the OK prompt). 
l When the REQ prompt is received after the 
program is loaded: 
Enter: PRT. 
l The Access Code Data Block will be output in the 
same format as it was input in the DACD Pro- 
gram. Example: REQ PRT 
ACB *7 
CBR **7 
CFD *9 
CFR **9 
etc. 
l...

PROGRAMMINGPROCEDURES 
SECTION 200-255-306 
FEBRUARY1992 
3. Class of Service Data Block (Table 6-3) 
3.01 
The Class of Service Data Block (DCOS 
Program) defines the 16 Classes of Service that 
are available in the system. All features that are 
controlled by the COS are allowed (except as 
indicated in notes 3 - 10) to all stations unless they 
are restricted in this Data Block. 
3.02 The DCOS Program assigns a number (0 - 
15) to each group of restrictions to be used. The 
number defined here is then...

PROGRAMMING PROCEDURES 
SECTION 200-255-306 
FEBRUARY 1992 
6. If a station is to be required to enter Verifiable Account Codes, the code VAC must be entered in 
the COS. This entry enables rather than denies this feature. 
7. If a station is to be required to enter Forced Account Codes on to// calls only, the code FATmust 
be entered in the COS. This entry enables rather than denies the feature. 
8. if a station is to be required to enter Forcedand Verifiable Account Codes, the codes FAC and VAC 
must...

PROGRAMMING PROCEDURES 
SECTION 200-255-306 
FEBRUARY 1992 
TABLE 6-3a 
CLASS OF SERVICE FEATURES AND CODES 
I 
FEATURE 1 CODE 
I Trunk Group 0 
Trunk Group 1 TO1 
Trunk Grouo 2 TO2 
1 Trunk Group 3 
I TO3 
I Trunk Group 7 
1 Trunk Group 14 
I T14 
I Trunk Group 15 
I DDIU Group 3 
DDIU Group 10 
DDIU Grouo 11 DlO 
Dll 
DDIU Group 12 
DDIU Group 13 D12 
D13 
DDIU Group 14 
DDIU GrouD 15 D14 
D15 FEATURE CODE 
Automatic Callback 
ACB 
Call Forward (All Calls/Station) 
CFD 
Call Forward/Busy (Station) 
CFB...

PROGRAMMING PROCEDURES 
SECTION 200-255-306 
FEBRUARY 1992 
TABLE 6-3a (continued) 
FEATURE CODE 
External Zone Paging (Zone 1) PEI 
External Zone Paging (Zone 2) PE2 
External Zone Paging (Zone 3) PE3 
External Zone Paging (Zone 4) PE4 
External All Paging (Zones 0 - 4) PEA 
All Paging (Group 00, Zones 0 - 4) PAL 
Direct Trunk Access 
DTA 
LCR Class 1 
LCl 
LCR Class 2 
LC2 
FEATURE CODE 
LCR Class 3 LC3 
ACD/MIS Call Pick-up 
APU 
ACD/MIS Call Be Picked-up ABPU 
Supervisor Monitor Tone and LCD Display...

PROGRAMMINGPROCEDURES 
SECTION 200-255-306 
FEBRUARY1992 
4. Print Class of Service Data Block (Table 6-4) 
4.01 To use the Print Class of Service Data Block 
(PCOS Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
Enter: PCOS (in response to the OK prompt). 
l When an REQ prompt is received after the 
program is loaded: 
Enter: PRT. 
l The COS Data Block will print out in the following 
format (see Table 6-3a for an explanation of 
feature codes): 
COS NO. 
COSO AAA BBB CCC DDD EEE...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
CHAPTER 7 
Al-i-ENDANT/STATION/DSS DATA 
1. Attendant Data Block (Table 7-I) 
1.01 The Attendant Data Block (DAlT Program) 
defines one or two attendant consoles in the sys- 
tem and selects the attendant options. Data is 
entered as follows: 
REQ (Request)-Indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data Block. 
CHG-To alter an existing Data Block. 
OUT-To delete an existing Data Block. 
AN0...

PROGRAMMINGPROCEDURES 
SECTION 200-255-307 
FEBRUARY1992 
TABLE7-1 
Procedure - Attendant Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
NOTES: (continued) 
1. Entries of 6 and 8 are allowed only in the Business mode. 
2. Designates the specific kind of paging accessed by the m button. 
/NT = Expanded Internal Group Paging (Group 0). 
EXT = External All Paging (Zones 0 - 4). 
N = External Paging to Zone N (0 - 4). 
ALL = Expanded Internal Group...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
TABLE 7-1 (continued) 
Error Codes 
Program Name: Attendant Data Block (DAlT) 
Error Code 
ERAT-T 00 
ERATT 01 
ERA-I-T 02 
ERAl-f 03 
ERATI- 04 
ERAl-F 05 
ERA-I-T 06 
ERA-I-I- 08 
ERA-IT 09 
ERA-I-T 10 
ERAl-T 11 
ERA-I-T 12 
ERA-I-T 13 
ERA-I-T 14 
Meaning 
A PCB is not equipped in that location. 
The PCB is not an NEKU type. 
The port is busy. 
The port has already been assigned to a station or DDIU (REQ = NEW). 
The port has not been...