Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

PROGRAMMINGPROCEDURES 
SECTION 200-255-307 
FEBRUARY1992 
TABLE7-8 
Procedure - DSS Console Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
m #NN 
7 
m Feature 8 
AUT L M XX (XXX, XXXX) 
9 
DUP M 10 
DUP MX Y 
11 
DUP MXX YY ZZ 
12 
(continued) 
NOTES: 
1. A maximum of eight DSS consoles may be assigned to each system. Up to two consoles may be 
assigned to a single electronic/digital telephone. N = 0 - 7. 
2. CNNx/LNNX represents the port...

10. 
11. 
12. 
13. 
PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
TABLE 7-8 (continued) 
Used to duplicate an entire DSS console button arrangement, M = number of the DSS console to 
be copied (0 - 7). 
Used to duplicate a row of DSS console buttons to another console. 
M (0 - 7) = Number of the DSS console being copied. 
x (0 - 5) = Row of the DSS console being copied. 
Y (0 - 5) = Row of the DSS console to which the copy will be applied. 
Used to duplicate specific buttons from one...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
TABLE 7-8a 
AVAILABLE FEATURES FOR DSS BUTTON ASSIGNMENT 
FEATURE ENTRY I NOTE 
Account Number (SMDR) 
I CRG 
I 
Alphanumeric Message 
Assistance (ACD) 
Automatic Callback MES 
AS.9 
AC6 
Automatic Dialing, Flexible 
I 1 
Automatic Dialing, Fixed 
Call Forward - All Calls FAD XXX 1 
CFD 
Call Forward - Busy 
I CFBY 
I 
Call Forward - Busy/No Answer CFBD 
Call Forward - No Answer 
Call Forward - Busy (System/DID) CFNA 
CFSN 
Call Pickup Directed...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
JANUARY 1993 
:--.+ 
TABLE 7-8a (continued) 
AVAILABLE FEATURES FOR DSS BUTTON ASSIGNMENT 
FEATURE ENTRY NOTE 
Speed Dial - Station (User) SDU XX 6 
Station-to-Station Message SSM 
I Status (Available/Unavailable) (ACD) 
I STAT 
I 
Stroke Count (ACD) 
System Night Operation 
Tap (Agent Monitor) (ACD) STRK 
SYS 
ATAP 7 
Universal Night Answer 
Voice Page 
Work Mode Cancel (ACD) UNA 
VCP 
CAN 
NOTES: 
1. There is a maximum of 500 Autodial buttons per system. 
2....

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
JANUARY 1993 
TABLE 7-8 (continued) 
Error Codes 
Program Name: DSS Console Data Block (DDSS) 
Error Code Meaning 
ERDSS 00 A PCB is not equipped in that location. 
ERDSS 01 The port has already been assigned (REQ = NEW). 
ERDSS 02 The wrong button number was entered. 
ERDSS 03 The input DSS console or feature button conflicts with the existing button. 
I I 
ERDSS 04 The PCB is not an NDSU/NDKU. 
ERDSS 05 The port is not assigned (REQ = CHG, OUT). 
ERDSS 06...

9. Print DSS Console Data Block (Table 7-9) PORCNNX (or PORLNNX)-All CNNX (or LNNX) 
data will be output. 
9.01 To use the Print DSS Console Data Block 
(PDSS Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). PORVAC-A list of all unassigned ports will be 
output. 
Enter: PDSS (in response to the OK prompt). STACNNX (or STALNNX)-All data regarding the 
l After the program has loaded and the REQ station that is associated with the DSS console 
prompt is received: (installed at either...

PROGRAMMING PROCEDURES 
SECTION 200-255-308 
JANUARY 1993 
CHAPTER 8 
MESSAGE CENTER DATA 
will allow internal DTMF signaling to 
these ports.) 
1. Message Center Data Block (Table 8-1) NOTE: 
If using a Toshiba INTOUCH Digital Voice 
1.01 The Message Center Data Block (DMCD Messaging System, do not make any entries 
Program) identifies the type of Message Center for the MDNO and MDNI prompts. Press the 
and its location. 
q key, 
REQ (Request)-Indicates that the program has 
loaded. Two responses are...

PROGRAMMINGPROCEDURES 
SECTION 200-255-308 
JANUARY1993 
I the INTOUCH or VP system. This provides en- will then prompt a 9” and any entries made will 
hanced integration of the PERCEPTIONeke, 
be deleted. 
I and INTOUCH or VP systems. Following the 
Enter: XXXX XXXX... (in response to the A 
TVMO prompt, the PERCEPTlONe or 
prompt). 
PERCEPTION,, system will prompt an “A.“Any XXXX XXXX... (in response to the D 
entries made will be added. To delete a port, 
press the carriage return m key. The system...

PROGRAMMING PROCEDURES 
SECTION 200-255-308 
JANUARY 1993 
5. If M WC0 = VM, enter up to 32 directory numbers (NSTU ports) that will be connected to the voice 
mail system. 
If MWCI = VM, enter up to 32 directory numbers (NSTUporfs) that will be connected to the voice 
mail system for Tenant 1 (TEN = Y). 
NOTE: Do not make any entries for these two rompts if using the Toshiba INTOUCH or VP Digital 
Voice Messaging System. Press the 
lb - key. 
6. This entry will appear when MWCO or MWCl = VM. 
7. If MWCO...

PROGRAMMING PROCEDURES 
SECTION 200-255-308 
JANUARY 1993 
2. Print Message Center Data Block (Table 8-2) 
2.01 To use the Print Message Center Data Block 
(PMCD Program): 
l Perform the Authorization Procedure (Level 1 or 
2). 
Enter: PMCD (in response to the OK prompt). 
l When the REQ prompt is received after the 
program is loaded: 
Enter: PRT. 
l The Message Center Data Block will output data 
in the same format as it was input in the 
DMCD 
Program. 
!r- 
.,: I 
Le. 
TABLE 8-2 
Procedure - Print...