Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

CHAPTER 10 
TOLL RESTRICTION DATA 
1. Toll Restriction Data Block (Tables 1 O-l - 1 O-4) 
1.01 The Toll Restriction Data Block (DTOL Pro- 
gram) defines the office codes and area codes to 
be allowed or denied by the Toll Restriction feature. 
1.02 There are ten classes of Toll Restriction for 
defining a station’s outward dialing privileges. Of 
these ten classes, eight may be customized (0 - 7), 
one restricts the dialing of numbers containing 0 or 
1 as the first or second digit (8), and one applies...

PROGRAMMINGPROCEDURES 
SECTION 200-255-310 
FEBRUARY1992 
When entering PAR in response to TYPE (Table 
10.2), the next prompt will be: 
HAC (Home Area 
Code)--Defines the area code 
in which the system is operating. Home area 
codes are also used to analyze a dialed number 
that does not contain an area code, Data that is 
entered here will appear in the Least Cost Rout- 
ing Data Block 
(DLCl Program, PAR table, HAC 
prompt). 
Enter: Area Code NO/IX. 
NOTE: 
N=2 -9, O/l=OorI, X=0 -9. 
ICC...

PROGRAMMINGPROCEDURES 
SECTlON200-255-310 
FEBRUARY1992 
TABLE10-2 
Miscellaneous Parameters Table 
Load the DTOL Utility Program. When the TYPE prompt is received, proceed as follows: 
NOTES: 
I. 
2. 
3. 
4. 
5. This entry is coupled with the HAC entry in the PAR table in Least Cost Routing (DLCl). Data that 
is entered here will also appear in that table. 
Informs the system if interchangeable codes are used (office codes with NO/lx format). 
SPCC 1 & 2 entries are the DN of any specialized common...

PROGRAMMINGPROCEDURES 
SECTION 200-255-310 
FEBRUARY1992 
When entering CLS in response to TYPE (Table 
NO/i X NO/i X etc. (in response to the D 
lo-3), the next prompt will be: prompt) to delete area codes. 
CNO 
(Class Number)---Indicates the number of 
the Toll Restriction class that is being defined. 
This number is used in response to the TOL 
prompt in the 
DEKT, DSIT, and DTGP Pro- 
grams . 
Enter: 0 - 7 (Class Number) or NOUT. 
NOTE: 
Enter OUT after the class number (N) 
in order 
to remove that...

PROGRAMMINGPROCEDURES 
SECTION 200-255-310 
FEBRUARY1992 
3. Codes cannot be added and deletedin the 
same pass through the table. A separate 
pass is required for each step. 
4. Following the OCDprompt, an ‘A”prompt 
will appear and any entered codes will be 
added. To delete, press the return key 
m. A ‘D” will appear and any entered 
codes will be deleted. RANGES EXAMPLE: 
4-digit Format Off ice Codes 
2209 220 - 229 
2316 231 - 236 
2478 247 - 248 
Restriction Class Table 
TABLE10-3 
Load the DTOL...

PROGRAMMINGPROCEDURES 
SECTION 200-255-310 
FEBRUARY1992 
When entering AOC in response to TYPE (Table 
lo-4), the next prompt will be: 
TN0 (Table Number)-Selects 
one of 32 area/ 
office code exception (AOC) tables. 
Enter: 0 - 31 (Table Number). 
ARC (Area Code)--Identifies the area code to which 
this AOC table is assigned. A maximum of eight 
AOC tables can be assigned to any area code 
(the table numbers must be sequential). 
Enter: Area Code NO/IX or NONE. 
NOTE: 
N=2-9, O/l=OorI, X=0-9. 
CNO...

PROGRAMMINGPROCEDURES 
SECTION 200-255-310 
FEBRUARY1992 
TABLE10-4 
Area/Office Code Exception Table 
Load the DTOL Utility Program. When the TYPE prompt is received, proceed as follows: 
ITEM 
PROMPT USER ENTRY NOTE 
TYPE 
AOC 
Table Number 
TN0 0 - 31 
Area Code 
ARC NO/l X or NONE 1 
Class Number 
CNO 0 1 etc. or NONE 
OFC 
Off ice Codes A NXXX NXX etc., or 2&3 
D NXXX NXX etc. 
NOTES: 
1. ARC identifies the area code to which this AOC is assigned. Format is NO/lx (N = 2 - 9, X = 0 - 
9). A maximum...

PROGRAMMINGPROCEDURES 
SECTION 200-255-310 
FEBRUARY1992 
2. Print Toll Restriction Data Block (Table 1 O-5) 
2.01 
To use the Print Toll Restriction Data Block 
(PTOL Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
Enter: PTOL (in response to the OK prompt). 
l When an REQ prompt is received after the pro- 
gram is loaded: 
Enter one of the following commands: CLSALL-All code tables (area, office and area/ 
office) will be output for all eight classes. 
CLSCNX-All code tables...

PROGRAMMING PROCEDURES 
SECTION 200-255-311 
FEBRUARY 1992 
CHAPTER 11 
DATA SWITCHING DATA 
1. Digital Data Interface Unit Data Block (Table 
11-I) 
1.01 The DDIU Data Block (DDIU Program) de- 
fines all parameters of a given Digital Data Inter- 
face Unit including the PDIU-DI and PDIU-DS. A 
DDIU Data Block must be completed for each 
DDIU/PDIU in the system. Not all of the prompts 
listed below are used for both DDlUs (-MA or 
-MAT) or PDlUs (-DI or -DS). The response given 
totheTYP (DDIU/PDIU type)...

PROGRAMMINGPROCEDURES 
SECTION 200-255-311 
FEBRUARY1992 
TEN (Tenant 
Number)-Assigns the data station 
to one of the two possible tenants in the system. 
Enter: 0 if tenant service is not selected in the 
System Data Block (TEN = N). 
0 or 1 to specify tenant, if tenant service 
is selected in the System Data Block 
(TEN = Y). 
NOTE: 
The TEN entry for a DDIU-MAT/PDIU-DI 
should be the same as the TEN entry for the 
electronic/digital telephone to which it is as- 
signed. 
KEY (Button...