Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

PROGRAMMING PROCEDURES 
SECTION 200-255-312 
FEBRUARY 1992 
second digit. In this case, the DDP is used to 
differentiate between the two code types (see 
example). If the ICC response is “N,” then calls 
will be made using the normal NPA formula of 
NO/i X and NNX. 
Enter: 1, 2, or 3 digits or NONE. 
Example: If ICC is ‘Y” and the DDP is pro- 
grammed as 1, then the dialed number209-1234 
is recognized as a call within the home area 
code, while the dialed number 1-209-555-l 234 
is recognized as a call...

NOTE: 
N=2-9, O/l=Oorl, X=0-9. 
ACD (Area Codes-Delete)-indicates the area 
codes that are to be deleted from this RNO. As 
codes are deleted from RN0 1 - 14, they are 
automatically added to RN0 15. Codes can only 
be deleted from RN0 15 by adding them to 
another RN0 (1 - 14). 
Enter: NO/i X NO/i X etc. 
When entering DLCl, AOC (Table 12-4), the 
next prompt will be: 
TN0 (Table Number)-Selects one of the 16 area/ 
office code modification (AOC) tables that are to 
be used. 
Enter: 01 - 16. 
ARC (Area...

PROGRAMMING PROCEDURES 
SECTION 200-255-312 
FEBRUARY 1992 
NOTE: 
Codes cannot be added and deleted in the 
same pass through the table. A separate pass 
is required for each step. 
3. Least Cost Routing Data Block 2 (Tables 
12-5 - 12-6) 
When entering DLC2, RTB (Table 124, the next 
prompt will be: 
RN0 (Route Table 
Number)-identifies the 
number of the Route Table to which an Area 
Code Table (ACT) and/or an AOC Table is 
assigned. Entering OUT will clear all Route 
Tables. Entering RN0 1 - 15,...

LC2 (Class 2 Routing Priority)-Same as LC2 in 
Schedule A, but for Schedule B time interval. 
Enter: Routing Choice (for example: RT3 RT2 
etc.). 
NONE. , . . or.. . 
LCl (Class 1 Routing Priority)-Same as LCl in 
Schedule A, but for Schedule B time interval. 
Enter: Routing Choice (for example: RTl RT6 
etc.). 
NONE. * * ’ or.. . 
SCHC (Route Schedule Q-Defines the time-of- 
day interval for the last of three possible routing 
schedules. The start time, which is the end time 
of Schedule B, and the end...

PROGRAMMINGPROCEDURES 
SECTION 200-255-312 
FEBRUARY1992 
Route Table TABLE12-5 
Load the DLC2 Utility Program. When TYPE is prompted, proceed as follows: 
Default values are noted in parentheses (), 
12-8  

PROGRAMMINGPROCEDURES 
SECTlON200-255-312 
FEBRUARY1992 
NOTES: 
TABLE12-5(continued) 
1. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. OUT = Will clear all Route Tables. NN OUT = Will clear Route Table NN. 
Route definition - maximum is six routes, 
Format is: XX = Trunk Group Number (0 - 15). 
MM = Modify Digits Table to be applied (1 - 12). Modify Digits Table 
must be entered. 
Existing Route Schedule data is printed automatically after the response to RT6prompt is entered. 
Time-of-day interval for this routing...

PROGRAMMINGPROCEDURES 
SECTION 200-255-312 
FEBRUARY1992 
When entering DLCP, MDT(Table 12-6), the next 
prompt will be: 
TN0 (Modify Digits Table 
Number)-Specifies the 
Modify Digits Table Number assigned to the 
defined routes in the Route Tables (RTl - RT6). 
The same Modify Digits Table may be used for 
more than one route. 
Enter: Table Number (1 - 12). 
DLT (Digits to be Deleted )-Defines the number 
of digits that are to be deleted from the start of a 
dialed number. The system will remove these...

PROGRAMMING PROCEDURES 
SECTION 200-255-312 
FEBRUARY 1992 
TABLE 12-6 (continued) 
Error Codes 
Program Name: Least Cost Routing Data Block (DLCl and DLCP) 
Error Code Meaning 
ERLCR 00 Input time (in seconds) is out of range (0 - 99). 
ERLCR 01 Area Code (N 0/1X) is out of range (N = 2 -9, X = 0 - 9). 
ERLCR 02 Route number is out of range (I - 15). 
ERLCR 03 
ERLCR 04 
ERLCR 05 Service Code error. 
Service Codes exceed the maximum (10). 
Table number is out of range (1 - 16). 
1 ERLCR 06 1 Office Code...

PROGRAMMINGPROCEDURES 
SECTION 200-255-312 
FEBRUARY1992 
4. Print Least Cost Routing Data Block (Table 
12-7) 
4.01 To use the Print Least Cost Routing Data 
Block 
(PLCR Program). 
l Perform Authorization Procedure (Level 1,2, or 
3). 
Enter: PLCR (in response to the OK prompt). 
l When the REQ prompt is received after the 
program is loaded, enter one of the following 
commands: 
LCRALL-Ail Least Cost Routing Data Blocks will 
be output. 
PAR-Miscellaneous Parameters Table will be 
output....

PROGRAMMINGPROCEDURES 
SECTION 200-255-312 
FEBRUARY1992 
TABLE12-7 
Procedure - Print Least Cost Routing Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT USER ENTRY NOTE 
OK 
PLCR 
- DISK LOADING - 
=JQ 1 
- EXECUTE - 
REQ 1 
NOTES: 
1. The following responses are possible: 
LCRALL = 
PAR = 
ACTALL = 
ACTRNXX = 
AOCALL - 
AOCNOXX = 
AOCRNXX = 
CODXXX = 
RTALL = 
RTXX = 
TGPXX = 
RTMDXX = 
MDTXX = 
2. - = 
. 
d ii = 
:m: Outputs all...