Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

PROGRAMMINGPROCEDURES 
SECTION 200-255-311 
FEBRUARY1992 
TABLEli-1 
Procedure 
- Digital Data Interface Unit Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM 
PROMPT 
OK DDIU 
- DISK LOADING - USER ENTRY NOTE 
Port Number 
REQ NEW, CHG, OUT 
POR LNNX 
DIU Style 
I PDIU 
I Y or N 
AT Commands ATC Y or N 
Type of DDIU/PDIlJ TYP DIUl or DIU2 
Directotv Number 
DN 1 - 4 diaits 
Hunt Directory Number 
I HNT I 1 - 4 digits or NONE 
Class of...

PROGRAMMING PROCEDURES 
SECTION 200-255-311 
FEBRUARY 1992 
SPECIAL NOTE: 
When a DlU2 is assigned, two key entries must be made in the DEKT PROGRAM as follows: 
I PROMPT 
I USER ENTRY 
I NOTE 
I 
KEY DIU LNNX 1 
KEY DRS 2 
NOTES: 
1. Port number of DIlJ attached to the electronic/digital telephone (Data ON). 
2. Data release button. 
TABLE V-la 
DDIU BUTTON ASSIGNMENTS 
DIRECTORY NUMBER ENTRY NOTE 
Single Call Ring SCR NNNN XXXX 1 
I Single Call No Ring SCN NN’NN XXXX 1 
I 
FEATURE 
Automatic Callback...

PROGRAMMINGPROCEDURES 
SECTION 200-255-311 
FEBRUARY1992 
TABLE114 (continued) 
Error Codes 
Proaram Name: DDIU Data Block (DDIU) 
Error Code 
I Meaning 
ERDIU 00 1 A PCB is not eauiooed in that location. 
ERDIU 01 The PCB is not an NDCU/NDKU or NMDU type. 
ERDIU 02 The oort is busv (REQ = CHG or OUT). 
ERDIU 03 
ERDIU 04 The port has already been assigned to a station, DSS console, DDIU, or PDIU (REQ = NEW). 
#1 was entered, but tenant service was not enabled in the Svstem Data Block. 
ERDIU 05 1 #l was...

PROGRAMMING PROCEDURES 
SECTION 200-255-311 
FEBRUARY 1992 
2. Print Digital Data Interface Unit Data Block 
l When a REQ prompt is received after the pro- I 
(Table 1 l-2) gram is loaded: 
Enter: PORALL. 
2.01 To use the Print Digital Data Interface Unit 
Data Block 
(PDIU Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
l All DDIU Data Blocks will be output in numerical 
order of ports (lowest first). 
Enter: PDIU (in response to the OK prompt). 
TABLE 11-2 
Procedure - Print...

PROGRAMMINGPROCEDURES 
SECTION 200-255-311 
FEBRUARY1992 
3. Modem Pooling Data Block (Table 11-3) 
3.01 The Modem Pooling Data Block (DMDM 
Program) identifies the Modem Pooling ports. The 
Modem Pooling Data Block is not used with the 
PDIU-DS. See the DDIU Data Block and the In- 
stallation Instructions section for Modem Pooling 
using the PDIU-DS. 
REQ (Request)-Indicates that the program has 
loaded. Two responses are possible: 
NEW-To assign a new Data Block. 
OUT-To delete an existing Data Block....

PROGRAMMING PROCEDURES 
SECTION 200-255-311 
FEBRUARY 1992 
TABLE 11-3 
Procedure - Modem Pooling Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT 
USER ENTRY NOTE 
OK DMDM 
- DISK LOADING - 
REQ 
NEW, OUT 
Port Number 
POR LNNX 
l&2 
NOTES: 
1. NN = PCB location. 
PERCEPTION, - LOO - Ll7/L75 - L26. 
PERCEPTION,, - LOO - L31. 
2. X = Circuit number (1 - 4). 
ignore line entered. 
Backspace. 
Stop printing and return to REQ. 
Exit...

PROGRAMMINGPROCEDURES 
SECTION 200-255-311 
FEBRUARY1992 
4. Print Modem Pooling Data Block (Table 11-4) program is loaded: 
Enter: PORALL. 
4.01 To use the Print Modem Pooling Data Block 
(PMDM Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
l All Modem Pooling Data Blocks will be output in 
numerical order of ports (lowest first). 
Enter: PMDM (in response to the OK prompt). 
l When the REQ prompt is received after the 
TABLEll-4 
Procedure - Print Modem Pooling Data Block...

CHAPTER 12 
LEAST COST ROUTING DATA 
1. Least Cost Routing Data Block (Table 12-1) 
1.01 The Least Cost Routing Data Block (DLCR 
Program) defines the proper outgoing trunk based 
on the outside number that is dialed. LCR stores 
and examines the number dialed, checking the 
area and/or office codes. Based on this examina- 
tion and the time of day, LCR chooses the proper 
trunk from a programmed route table. The LCR 
Data Block has been divided between two utility 
programs (DLCI and DLC2). 
l DLCl...

PROGRAMMINGPROCEDURES 
SECTION 200-255-312 
FEBRUARY1992 
2. Least Cost Routing Data Block 1 (Tables 
12-2 - 12-4) 
When entering DLCI , PAR (Table 12-2), the next 
prompt will be: 
ICC (Interchangeable Codes)-A “Y” informs the 
system that interchangeable codes are used. 
These are office codes that have 0 or 1 as the 
second digit (NO/i X format). Area codes will be 
identified as the three digits following the DDD 
prefix. Office codes will be identified as the first 
three digits when a DDD prefix is...

PROGRAMMINGPROCEDURES 
SECTION 200-255-312 
FEBRUARY1992 
TABLE12-2 
Miscellaneous Parameters Table 
Load the DLCI Utility Program. When TYPE is prompted, proceed as follows: 
ITEM 1 PROMPT 1 USER ENTRY 
I NOTE 
I TYPE 1 -PAR I 
Interchangeable Codes 
“0” Call Timeout ICC 
OTO Y or N 
Time in seconds: 0 - 99 1 
Return Dial Tone after LCR Access Code 
Warning Tone to caller when the 
most expensive route is selected 
RTD 
WTA Y or N 
Y or N 
Home Area Code 
! .lxAc NO/l X (Home Area Code) 2 
Toll Free...