Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

CHAPTER 13 
LODGING/HEALTH CARE DATA 
1. Lodging/Health Care Features Data Block 
(Table 13-l) 
1 .Ol 
The Lodging/Health Care Features Data Block 
(DHMF Program) defines the number of miscella- 
neous parameters that pertain to the Lodging/ 
Health Care features. Data is entered as follows: 
NOTE: 
Be sure to run the DMYC program (Back-up 
Memory Check Entry Procedure) when the 
system is put into the Lodging/Health Care 
mode of operation, and before this program is 
entered, 
REQ (Request)-Indicates...

PROGRAMMING PROCEDURES 
SECTION 200-255-313 
FEBRUARY 1992 
TABLE 13-I 
Procedure - Lodging/Health Care Features Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT 
USER ENTRY NOTE 
OK DHMF 
- DISK LOADING - 
REQ NEW, CHG, OUT 1 
Automatic Wake-up Source 
AWU SRC MOH, VCE, or NONE (NONE) 2 
Automatic Wake-up 
AWU POR SMDR, TTY, or NONE (NONE) 
Message Waiting 
MW POR SMDR, TTY, or NONE (NONE) 
Message Registration 
MR POR SMDR, TTY, or...

PROGRAMMINGPROCEDURES 
SECTION 200-255-313 
FEBRUARY1992 
2. Print Lodging/Health Care Features Data 
Block (Table 13-2) 
l When an REQ prompt is received after the pro- 
gram is loaded: 
Enter: PRT. 
2.01 To use the Print Lodging/Health Care Fea- 
tures Data Block 
(PHMF Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
l The Lodging/Health Care Features Data Block 
will be output, with features listed in the order that 
they were input in the 
DHMF Program. 
Enter: PHMF (in response...

PROGRAMMING PROCEDURES 
SECTION 200-255-313 
FEBRUARY 1992 
3. Message Registration Data Block (Table 
13-3) 
3.01 TheMessage Registration DataBlock(DMRD 
Program) defines all parameters for the Message 
Registration feature. 
REQ (Request)-Indicates that the program has 
loaded. Two responses are possible: 
CHG-To change an existing Data Block. 
OUT-To delete an existing Data Block. 
ICC (Interchangeable Codes)-A “Y” informs the 
system that interchangeable codes are ,used. 
These are office codes that...

PROGRAMMINGPROCEDURES 
SECTION 200-255-313 
FEBRUARY1992 
RANGES EXAMPLE: 
4-digit Format Off ice Codes 
2209 220-229 
2316 231 -236 
2478 247-248 
TABLE13-3 
Procedure 
- Message Registration Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM PROMPT USER ENTRY NOTE 
OK DMRD 
- DISK LOADING - 
=Q 1 CHG; OUT 
I I 
interchangeable Code? ICC 1 Y or N (N) 
I 
1 1 - 3 digits or NONE (NONE) 
! 
DDD Prefix DDP 
! 1 NO/lx (NONE) 
! 
Home Area Code HAC...

PROGRAMMING PROCEDURES 
SECTION 200-255-313 
FEBRUARY 1992 
TABLE13-3(continued) 
Error Codes 
Error Code 
ERMRD 00 
ERMRD 01 Program Name: Message Registration Data Block (DMRD) 
Meaning 
Numeric error (0 - 9). 
Area Code (NO/IX) is out of range (N = 2 - 9, X = 0 - 9). 
ERMRD 02 Supervision Time is out of range (0 - 120). 
ERMRD 03 Billing Interval is out of range (1 - 180). 
ERMRD 04 Billing Unit is beyond time (0 - 100). 
ERMRD 05 Unit Cost is bevond limit (1 - 500). 
ERMRD 06 
ERMRD 07 
ERMRD 08...

4. Print Message Registration Data Block(Table 
13-4) 
4.01 To use the Message Registration Data Block 
(PMRD Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
Enter: PMRD (in response to the OK prompt). 
l When an REQ prompt is received after the pro- 
gram is loaded: 
Enter: One of the following commands: 
MRDALL-Ail Message Registration Data will be 
output. There may be a delay in the output after 
the OCA prompt. 
PROGRAMMINGPROCEDURES 
SECTION 200-255-313 
FEBRUARY1992...

PROGRAMMING PROCEDURES 
SECTION 200-255-314 
FEBRUARY 1992 
CHAPTER 14 
SPEED DIAL LIST DATA 
1. Speed Dial List Data Block (Table 14-I) 
1.01 The Speed Dial List Data Block (DSDL Pro- 
gram) contains all numbers stored on the 90- 
number Speed Dial - System list and the 50 lo- 
number Speed Dial - Station lists. 
1.02 The DSDL Program allows initial storage or 
changes to any speed dial list from the mainte- 
nance terminal. Data is entered as follows: 
REQ (Request)--Indicates that the program has...

PROGRAMMING PROCEDURES 
SECTION 200-255-314 
FEBRUARY 1992 
TABLE 14-l 
Procedure - Speed Dial List Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows. 
ITEM PROMPT 
USER ENTRY NOTE 
OK DSDL 
- DISK LOADING - 
I RN 
I List Number 
I LNO 
I Store Number 
I STR 
STR 
I I RR0 
CHG, OUT 
0 9’ NPANN XXXXX 
I 2&3 
19’ NPANN XXXXX I 
2 9* NPANN XXXXX 
ma! 
Repeat program, if necessary. 4 
NOTES: 
1. XX = List number. 
00 = System List (90 numbers maximum: 10...

2. Print Speed Dial List Data Block (Table 14-2) 
2.01 To use the Print Speed Dial List Data Block 
(PSDL Program): 
l Perform the Authorization Procedure (Level 1,2, 
or 3). 
Enter: PSDL (in response to the OK prompt). 
l When the REQ prompt is received after the 
program is loaded: 
Enter one of the following commands: 
ALL-All of the Speed Dial lists will be output. 
SYST-System Speed Dial list will be output. 
LSTXX-Station Speed Dial list XX will be output. 
PROGRAMMINGPROCEDURES 
SECTION...