Toshiba Perception E Ex Digital Pbx Installation And Maintenance Manual

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
2. Electronic/Digital Telephone Data Block 
(Table 7-2) 
2.01 The Electronic/Digital Telephone Data Block 
(DEKT Program) defines all parameters for each 
electronic/digital telephone. A separate Electronic/ 
Digital Telephone Data Block must be completed 
for each electronic/digital telephone in the system. 
Data is entered as follows: 
REQ (Request)-Indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data...

and voice-announce capability of this electronic/ 
digital telephone. 
Enter: Y or N. 
DIS (Display Electronic/Digital Telephone)-A 
“1” or “2” response activates the LCD display on 
the electronic/digital telephone (maximum dis- 
play electronic/digital telephones in the system 
may equal the total number of allowable sta- 
tions). 
Enter: 1, 2, or NONE. 
(1 = 2000-series Electronic LCD Tele- 
phone, 
2 = 6000~series Electronic/l OOO-series 
Digital LCD Telephone, 
NONE = Not an Electronic/Digital LCD...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
JANUARY 1993 
number above. For example: SCR NNN 
#X. 
X = Distributed Hunt Group Number (0 
- 3). Maximum: 8 stations per group. 
Data Directory Number Button Assign- 
ment: 
0 
0 
0 
NOTES: DIU LNNX-Data Port Assignment. 
Incoming data calls will audibly ring 
the electronic/digital telephone. 
NN = PC9 location for NDCU or NMDU 
PC9 or adjacent port location for 
NDKU. 
X = circuit number. 
An electronic telephone/DDIU-MAT 
combination will use two station...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
JANUARY 1993 
UNA-Universal Night Answer 
VCP XXXX-Voice Page (XXXX = DN to be 
paged.) 
ACDS XXXX-ACD Supervisor Line 
ACDA XXX-ACD Agent Line 
ASST-Assistance 
LOG-Log-in/out 
MONT-Monitor 
OCA-Off-hook Call Announce 
STAT-Status Available/Unavailable 
STRK-Stroke Count 
ATAP-Agent Monitor 
CAN-Work Mode Cancel 
NOTE: 
The system does not check to verify if two 
buttons are assigned the same feature. When 
programming digital telephones (DKT= Y), do...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
JANUARY 1993 
TABLE 7-2 
Procedure - Electronic/Digital Telephone Data Block 
Authorization Procedure must be completed. If an OK response is received, proceed as follows: 
ITEM ‘: PROMPT 
USER ENTRY NOTE 
OK DEKT 
- DISK LOADING - 
I 
I REQ I NEW, CHG, OUT I1 
Port Number POR LNNX 
l&2 
Digital Key Telephone DKT Y or N 
Number of Buttonstrips KS 1 or2 
3 
Class of Service Group cos o-15 
4 
Tenant Number 
I TEN 
I 0 or 1 I 5 I 
Call Pickup Group 
I PUG I 0 -...

PROGRAMMINGPROCEDURES 
SECTION 200-255-307 
FEBRUARY1992 
TABLE7-2a 
ELECTRONIC/DIGITALTELEPHONEBUTTONASSlGNMENTS 
DIRECTORY NUMBER ENTRY 
NOTE 
Single Call Ring 
SCR Nmm XxXx 1 
Single Call No Ring 
Station Hunt Distributed SCN N’NNN XXXX 1 
+bx 2 
I ACD/MIS DIRECTORY NUMBER 
I ENTRY 
I NOTE 1 
ACD/MIS Supervisor Line 
ACD/MIS Agent Line ACDS XXXX 3 
ACDA XXX 4 
I DATA DIRECTORY NUMBER 
I ENTRY 
I NOTE 
I 
/ Data Port Number 
Data Release DIU LNNX 5 
DRS 
PRIVATE CO LINE 
Private Line Ring 
Private Line...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
TABLE 7-2a (continued) 
I 
FEATURE 
! ENTRY 
NOTE 
I Do Not Disturb 
I DND 
I 
Flash FLH 
10 
Hundreds Group HNG XX 
11 
Log-in/out (ACD) LOG 
I Manual Signaling 
I SIG LNNX 
I 12 
Message Waiting 
Monitor (ACD Supervisor) MSG 
MONT 
I .Off-hook Call Announce 
I OCA 
I 
Override 
Paging, External 
Paging, internal OVR 
PEXT 
PINT 13 
14 
I Call Park 
Privacy Release PRS 
Release RLS 
Repeat Last Number Dialed RND 
I Speaker Cut-off 
Speed Dial -...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
7. There is a maximum of 500 Autodial a buttons per system. 
8. XXX = Fixed digits to be dialed (maximum: 16 digits/* = pause). 
9. This feature can on/y be assigned to 2000~series electronic/l OOO-series digital LCD telephones. 
IO. The Flash button causes a 500 ms or a 1 -second flash to a CO trunk. 
11. XX = Leading one or two digits (1 - 9) designating the Hundreds Group to be activated on an associated 
DSS console (switched operation...

PROGRAMMING PROCEDURES 
SECTION 200-255-307 
FEBRUARY 1992 
TABLE 7-2 (continued) 
Error Codes 
Error Code 1 Program Name: Electronic Telephone Data Block (DEKT) 
Meaning 
1 EREKT 20 1 The SDC has already been assigned to this Speed Dial. 
-1 
1 EREKT 21 1 The input port is not an NEKUINDKU port (SIG LNNX). 
EREKT 22 PVR NNN/PVN NNN is entered, but trunk DN NNN has not been assigned. 
EREKT 23 The input DN is a trunk DN (VCP NNN Hunt DN). 
EREKT 24 32 DNs have already been assigned to the Distributed...

3. Standard Telephone Data Block (Table 7-3) 
3.01 The Standard Telephone Data Block (DSTT 
Program) 
defines all parameters for a given stan- 
dard telephone. One Data Block must be com- 
pleted for each standard telephone in the system. 
Data is entered as follows: 
REQ (Request)--indicates that the program has 
loaded. Three responses are possible: 
NEW-To create a new Data Block. 
CHG-To alter an existing Data Block. 
OUT-To delete an existing Data Block. 
NOTE: 
If OUT is entered, then only the port...