Telrad Digital Digital Family Of Systems Operating Instructions

76-110-0165/G, Issue 1
44
3-44
To program call forwarding
Avanti 3025
and 3020 sets
(PBX sets: First press the DN button for which you want your calls for-
warded. Then:)
1. Press 
CALL FORWARD softkey
NOTE
If you are authorized, you can execute call for-
warding for all your DNs at once. If so, press the
 
CALL FORWARD 
softkey and then {FWD DNS} 
which only appears on authorized sets).
2. Press the appropriate softkey to select the type of call forward that
you want to program - 
{CALL FWD}, {BUSY} or...

Section 3: AVANTI FAMILY SETS OPERATING INSTRUCTIONS
45
3-45
Buttons marked [CA AL] and [CY AL] are de-
fault-programmed for ALL calls (both internal and 
external). 
To forward all calls (both internal and external) 
to an internal destination:
1. If you are programming a specific DN button on a PBX mode set, 
first press the desired DN button. Otherwise, skip to the next step.
 
2. Dial one of the CALL FORWARD access codes followed by [2],
or
Press a button programmed for forwarding ALL calls...

76-110-0165/G, Issue 1
46
3-46
warding, and then:
2. Press
 {DELETE}
3. Press {EXIT}
- The appropriate DN button stops flashing and set returns to the 
idle state.
Key mode sets:
1. Press the flashing [DND] button.
-The [DND] button stops flashing and dial tone returns to the nor-
mal state.
Any other set To cancel call forwarding of all calls:
1. If you programmed call forwarding for a specific DN button on a PBX 
mode set, first press that DN button. Otherwise, skip to the next 
step.
2. Press [#].
3....

Section 3: AVANTI FAMILY SETS OPERATING INSTRUCTIONS
47
3-47
ple: CALL FORWARD INTERNAL).
4. Hang up
Canceling Call forward to me
If another extension has programmed Call forward to your extension 
and you want to cancel this status, proceed as follows:
Avanti 3025/
3020/3015D
sets1. Press {CANCEL}.
2. Press {FLW TO ME} ({FL 2ME} on 3015D.
3. Press 
{ALL} or enter the DN of the extension which programmed
Call forward to your extension
4. . Hang up
Any other set1. Dial the CANCEL access code ([#])
2....

76-110-0165/G, Issue 1
48
3-48
digit in the string and, in effect, occupies the equivalent of two digits.
TONE DIAL - This is used when you are dialing on a line defined as 
pulse dialing, but you wish to switch over to tone dialing (e.g. for voice 
mail services). From Avanti 3025/3020/3015D sets, use the 
{TONE DI-
AL}
 button. On other sets, press [P®
T] (Pulse_Tone), otherwise, con-
sult your System Administrator. 
T appears on the display and, in effect, 
occupies the equivalent of two digits.
PAUSE...

Section 3: AVANTI FAMILY SETS OPERATING INSTRUCTIONS
49
3-49
4. Dial the new number to be stored (up to 16 digits, including the spe-
cial characters described above, which are accessed by pressing
{FLASH SIG}, {XFER}, {TONE DIAL} or [PAUSE].
- Display shows the digits as you enter them.
5. Press
 {SAVE}
6. Hang up.
All other sets1. Press [FEATURE] and then [PROGRAM].
2. Dial the speed dial code (3 digits) for one of the available memories
or press the desired SPEED DIAL button.
3. Dial the new number to...

76-110-0165/G, Issue 1
50
3-50
2. Press the MEMORY button you want to program.
- Display sets show 
MEMORY KEY, the number representing the 
MEMORY button (each MEMORY button on your set has an as-
signed number) and the currently programmed extension or fea-
ture (if one exists).
3. Dial the new number (extension or feature access code).
- On display sets, the digits (or name of the extension or feature) 
appear as they are dialed.
- Hang up.
To display a number programmed for a MEMORY button  
(Display...

Section 3: AVANTI FAMILY SETS OPERATING INSTRUCTIONS
51
3-51
3:15 pm would be entered as 1515).
4. Press [SR].
Non display
sets1. Press  [FEATURE] (or dial the FEATURE access code) and [8][2].
2. Enter the alarm time, in the form HHMM. Use two digits (00 through
23) for the hour and two digits (00 through 59) for the minutes (e.g.
3:15 pm would be entered as 1515).
3. Press [PROGRAM].
If you want to exit in the middle of the time setting procedure, press 
[FLASH].
When the alarm rings, you can stop it...

76-110-0165/G, Issue 1
52
3-52
3.21 ADJUSTING THE VOLUME
The volume of your telephone set speaker and handset can be adjust-
ed, as needed.
Use the [LO    HI] button to adjust the speaker volume during a regular 
speakerphone call or while you hear dial tone via the speaker. This 
same volume setting applies for handsfree answerback (HFAB) calls.
If you are talking via your handset, you can set level with [LO    HI] but-
ton.
While a call is ringing at your extension, use the [LO    HI] button to ad-...

Section 3: AVANTI FAMILY SETS OPERATING INSTRUCTIONS
53
3-53
To end the conversation with the person at the door
•Press [FLASH] or hang up.
- The extension is disconnected from door unit.
-[EXT PAGE] button indicator goes off.
3.23 BACKGROUND MUSIC (BGM) 
If equipped, the background music (BGM) feature option allows users 
to listen to a source of music, such as a radio or tape recorder, through 
the station speaker, when your telephone set is not being used. While 
you are listening to the music, your...