Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Station Message Detail Recording 2-273
Chapter 2 - Features and Operation
SMDR Port Assignments
Description
PORT #1-- RS-232C port labeled SCMI on the MPB (recommended for maintenance use only)
PORT #3 -- Refers to the RS-232C connector on the optional SIU (recommended for ACD, 
ICLID, and SMDR uses)
PORT #4 -- Refers to the RS-232C connector on the optional SIU (recommended for ACD, 
ICLID, and SMDR uses)
PORT #5 -- Refers to the UART on the MPB2 (recommended for ACD, ICLID, and SMDR uses)
Programming...

2-274St ation Relocation
Chapter 2 - Features and Operation
Station Relocation
Description
The Station Relocation Feature lets a user unplug their station and plug it into another 
location. Dialing a code followed by the old station number brings all the station attributes 
including extension number, button mapping, speed dial, and class of service to the new 
location.
Operation
1. A station can be relocated by unplugging it, then plugging it into a new location.
2. Dial [636] on the dial pad. Then,...

System Parameters2-275
Chapter 2 - Features and Operation
System Parameters
Initialize System Parameters
Description
System Parameters may be initialized to set all data fields to their original default values. The 
following data fields are returned to their default values upon initializing the System 
Parameters.
Table 2-23: System Parameter Defaults
Program CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
FLASH 01 SYSTEM TIMERS
1System Hold Recall Timer 60 sec
2 Exclusive Hold Recall...

2-276System Parameters
Chapter 2 - Features and Operation
FLASH 05 SYSTEM FEATURES 1
1 Attendant Override Disabled
2 Hold Preference System
3 External Night Ring Disabled
4 Executive Override Warning Tone Enabled
5 Page Warning Tone Enabled
6Background Music Enabled
7 Least Cost Routing (LCR) Disabled
8 Account Codes - Forced Disabled
9 Group Listening Disabled
10 Idle Speaker Mode Disabled
11 Call Cost Display Feature Disabled
12 Music-On-Hold Enabled
13 Call Qualifier Tone Disabled
FLASH 06 SYSTEM...

System Parameters2-277
Chapter 2 - Features and Operation
FLASH 07 FLASH RATES 
1 Incoming CO Line Ringing Red 480 ipm flutter
2 Incoming Intercom Ringing Red 120 ipm flutter
3 Call Forward Button Red Steady On
4 Message Wait/VM Button Red Steady On
5Message CallBack – DSS/BLF Red 120 ipm flutter
6Do Not Disturb – DSS/BLF Red 60 ipm Dbl Wink
7 Auto CallBack – DSS/BLF Red 120 ipm flash
8 UCD Available/Unavailable – DSS/BLF Red 60 ipm Dbl Wink 
9 Transfer CO Ringing Red 120 ipm flash
10 Recall CO Ringing...

2-278System Parameters
Chapter 2 - Features and Operation
Programming Steps
1. Press the SYSTEM PARAMETERS flexible button (FLASH 80, Button #1). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
2 Station Range (FROM) 1000
3 Station Range ( TO) 8999
4IP Address None
5 Ext BLF Cards 1-28 None
6 Check Status 0-1 Disabled
FLASH 20 1 DISA Access Code 100
2 Database Admin Password 3226
FLASH 21 1 SMDR Enable/Disable No
2 Long Distance/Local Assignment Long Distance
3...

System Parameters2-279
Chapter 2 - Features and Operation
Print System Parameters
Description
The currently stored customer database can be printed or uploaded into a file. This command 
dumps the entire database as a permanent record which can serve as a hardcopy of the 
database. The system baud rate must match that of the printer or receiving device. When 
printing the System Parameters the following data prints:

All System Timers

All System Wide Options (External Night Ringing, Hold Preference)...

2-280System Parameters
Chapter 2 - Features and Operation
MUSIC CHANNEL[3..8] CABINET SLOT TYPE
CO - ## #### ## ## ## ------- ---- ----
0 0 DT24
ATTENDANT STATIONS 0 1 DTIB
100 ## ## ## ## ## ## 0 2 DTIB
0 3 NONE
DATE & TIME FORMAT 0 4 SLIB
MM/DD/YY, 12 HOURS 0 5 NONE
0 6 LCOB
PBX DIALING CODES 0 7 PRIB
## ## ## ## ## 0 8 LCOB
0 9 MPB
EXECUTIVE/SECRETARY PAIRINGS 1 0-9 NONE
1 = ### ### 2 0-5 NONE
2 = ### ### 3 0-5 NONE
3 = ### ###
4 = ### ###
----------------------------
ON BOARD RELAY ASSIGNMENTS
NONE...

System Reset2-281
Chapter 2 - Features and Operation
Programming Steps
1. Press the SYSTEM PARAMETERS flexible button (FLASH 85, Button #1). The following 
message displays:
2. To print the System Parameters database, press the HOLD button. The following message 
displays:
When the system finishes sending the information to the printer, a confirmation tone 
sounds.
System Reset
Description
The System Reset feature provides a hard system reset from the keyset instead of the KSU. 
This is useful in cases...

2-282T- 1  Tr u n k i n g
Chapter 2 - Features and Operation
T- 1  Tr u n k i n g
Description
The T-1 trunk card can be used to connect 24 lines (24 channels per T-1 circuit) from a CO to 
the system. These lines can be any mix of inbound WATS, outbound WATS, standard DDD 
lines, DID lines, or TIE lines. The system also supports Fractional T-1 Service.
T- 1  S i g n a l i n g  Ty p e
Description
The T-1 trunk card provides the XTS Digital Systems with the ability to connect to digital T-1 
trunk...