Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Toll Restriction2-303
Chapter 2 - Features and Operation
Special Table
Description
The Special Tables provide greater flexibility in designing a toll plan for a particular site.

Each Special Table allows entry of up to 800 office codes (200–999).

Three of these tables must be assigned an area code by which they are referenced. The 
fourth table is reserved for the home area code and requires no area code entry.

The Special Tables are referenced through entries in the allow tables. Four area codes,...

2-304Toll Restriction
Chapter 2 - Features and Operation
To enter office codes in a special table:
1. Press the SPECIAL TABLE (#1 to #4) flexible button (FLASH 70, Buttons #5 to #8) that 
corresponds to the area code programmed above. The following message displays:
XXX = Area Code
2. Enter the office codes that are to be allowed or removed as follows:
XXX [1] = Allow Code
XXX [0] = Remove Code from the list
(XXX = An office code from 200 to 999)
3. Press HOLD after every code entered. A confirmation...

Toll Restriction2-305
Chapter 2 - Features and Operation
Press the DISPLAY TABLES button again, the next 6 entries display. This continues until all 
codes are displayed.
XXX= Area Code
YYY= Allowed Office Code
Initialize Exception Tables
Description
The Exception Tables parameters, including the Allow/Deny Tables and the Special Tables, 
may be initialized setting all tables to their original, default values. The following Tables are 
cleared returning to their default value upon initializing the...

2-306Toll Restriction
Chapter 2 - Features and Operation
Print Exception Tables
Description
The Print Exception Tables command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
When printing information from the Exception Tables, the following data prints:

Allow Table A and Deny Table A

A ll o w  Ta b l e  B  a n d  D e n y Ta b l e  B

Special Tables 1, 2, 3, and 4
Figure 2-22:...

Toll Restriction2-307
Chapter 2 - Features and Operation
Programming Steps
1. Press the EXCEPT TABLES flexible button (FLASH 85, Button #5). The following message 
displays:
2. To print the Except Tables, press the HOLD button. The following message displays:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
Toll Restriction Related Items
CO/PBX Lines
When CO lines are marked as PBX lines the system first checks the PBX code table for a valid 
match....

2-308Uniform Call Distribution
Chapter 2 - Features and Operation
Two (2) options are available to help alleviate this problem:
1. Shorten the SLT receiver timer [FLASH 01] [Button 12]. This frees up DTMF receivers faster, 
but may not provide the desired toll restriction for SLT stations.
2. Enable LCR and force LCR on SLT stations. 
When the LCR database is set up, the 3-digit table allows entry of the number of digits to 
expect. When a SLT dials the appropriate number of digits, LCR releases the DTMF...

Universal Day/Night Answer2-309
Chapter 2 - Features and Operation
Universal Day Answer (UDA) 
Description
UDA-assigned CO lines can signal over external page port(s). External Day ringing is 
programmed on a system-wide basis in administrative programming. Stations that do not 
have access to a line during the day can answer that line while the System is in the day mode 
by dialing a UDA code [#5]. To use this feature, a LOOP button or an appearance of the trunk 
must be present on the station....

2-310Univer sal Day/Nig ht  A ns we r
Chapter 2 - Features and Operation
» If External Day ring is disabled, or the system is not in the day mode, external page 
ringing is disabled.
» Ringing CO lines not assigned CO line group access for a particular SLT may be answered 
in a UDA service. Dialing privileges are unavailable on CO lines to which an SLT does not 
have access. CO lines without UDA status may not be answered or accessed via UDA 
procedures.
» If two single-line telephones attempt to...

Voice Mail2-311
Chapter 2 - Features and Operation
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … UNA is enabled.
Vo i c e  Ma i l  
Description
Up to 8 Voice Mail groups can be configured in the XTS system. Each group can contain up to 
24 Voice Mail designated ports, each of which interfaces with a port on an SLT card (or DIDB if 
using a Digital Voice Mail).
An externally provided...

2-312Vo i c e Ma i l
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [65]. The following message displays.
XXXX = 3- or 4-digit flexible voice mail group number
The top left button in the flexible button field is lit for programming Voice Mail Group 
440.
2. To change Voice Mail groups or enter further voice mail groups, press the appropriate 
flexible button 1-8 (440–447) and perform the following procedures.
DEFAULT … All Voice Mail stations are assigned to Voice Mail Group...