Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Voice Mail In-Band Features2-323
Chapter 2 - Features and Operation
Programming Steps
1. Press the VOICE MAIL GROUP flexible button (FLASH 85, Button #13). The following 
message displays:
2. To print data for Voice Mail Group Parameters, press the HOLD button. The following 
message displays:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
Voice Mail In-Band Features
In-Band Signaling Integration
Description
The XTS allows programming so that if a...

2-324Voice Mail In-Band Features
Chapter 2 - Features and Operation
Programming Steps
Press FLASH and dial [67]. The following message displays:
Voi ce  Ma il  In - B an d  D ig i t s
Description
The Voice Mail In-Band Digits feature enables and disables station in-band signaling. 
Incoming CO callers can be Station Call Forwarded into voice mail only when the ringing CO 
line is programmed to ring at one station. CO lines programmed to ring at an Attendant 
station, call forward into the voice mail...

Voice Mail In-Band Features2-325
Chapter 2 - Features and Operation
2. Enter a 0 or 1 to Enable/Disable this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … VM Transfer/Forward feature is enabled.
Voice Mail Broker
Description
The Voice Mail Broker Calls feature modifies the operation of voice mail ports when disabled. 
Broker operation is unavailable when using supervised transfers to stations. When enabled, 
the...

2-326Voice Mail In-Band Features
Chapter 2 - Features and Operation
Remote Voice Mail Programming
Description
This feature is used to specify the pilot hunt number of the centralized voice mail system in a 
networking system. Refer to “Remote Voice Mail Programming” on page C-26.
Voi ce  Ma il  Mo dem  Acc e ss
Description
You can program Vodavi voice mail systems (other than MiniVoice or PathFinder) using the 
telephone system modem.
Programming Steps
To enable or disable the VM port:
1. Press the VM...

Voice Mail One-Touch Recording 2-327
Chapter 2 - Features and Operation
Conditions
» The use of this feature requires the use of a straight-thru modem cable connected from 
the voice mail system to one of three ports on the XTS system. Use either port 5 on the 
MPB2 or ports 3 or 4 on the optional SIU.
Voice Mail One-Touch Recording
Description
The Voice Mail One-Touch Recording feature allows the station user, while on an internal/
external call, to press a button and have the system record the...

2-328 Vo ic e Ma il O n e- To u ch  Rec o rd i n g
Chapter 2 - Features and Operation
Conditions
» If the user hangs up without terminating the record function, the system performs the 
exit procedure as described in step 3 above.
» If the user presses the TRANS, CAMP ON, MSG, or FWD buttons during recording, pressing 
the button is ignored.
» During the recording setup, pressing the CONF button is ignored.
» If a VM port is not available when the station user wants to record, the user receives the...

Voice Mail Outpulsing Table2-329
Chapter 2 - Features and Operation
Programming Steps
1. Press the ONE-TOUCH RCD WARNING TONE flexible button (FLASH 06, Button #10). The 
following message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the use of this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Recording Warning Tone is enabled.
Vo i c e  Ma i l  O u t p u l s i n g  Ta b l e
Voice Mail In-Band Signaling
Description
Entries...

2-330Vo i c e  M a i l  O u t p u l s i n g  Ta b l e
Chapter 2 - Features and Operation
Suggested Uses:

Build a table (0 for example) for any additional digits other than the station extension 
number (e.g., Voice Mail Box number) needed for a caller to leave a message in a station’s 
mailbox (Leave).

Build another table (1 for example) for any additional digits needed for a mailbox holder 
to retrieve a message (Retrieve). By Default:
Programming Steps
1. Press FLASH and dial [66]. The following...

Voice Over the Internet Protocol 2-331
Chapter 2 - Features and Operation
Voice Mail Disconnect Table
Description
A disconnect signal can be programmed into the XTS system to notify the VM system that a 
call has been abandoned. This is accomplished through in-band signaling. If a CO or Intercom 
disconnect signal is detected, the XTS system sends a series of DTMF digits programmed in 
the voice mail disconnect table to the voice mail port. This can be any digit stream up to 
12 digits including [

] and...

2-332Vo l u m e  C o n t r o l
Chapter 2 - Features and Operation
Volume Control 
Operation
DIGITAL AND ELECTRONIC TELEPHONES
The volume control on the Digital Key Telephone controls ringing, handset, and 
speakerphone volumes. It also affects the receive volume of the Wanderer cordless unit. The 
volume on 8-button digital telephones is controlled by dialing feature code 638 and then 
using [#] to increase volume or [

] to decrease volume.
The volume control on the Electronic Key Telephone consists of...