Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Vo l u m e  Co nt ro l2-333
Chapter 2 - Features and Operation
Using the handset on a CO call ...
Receiving a page announcement ...
Receiving an incoming tone ringing Intercom or CO call ...
.

SINGLE LINE TELEPHONE
The volume control on the Single Line Telephone is located on the right side of the 
telephone. The slider switch options are HI for loud volume, LO for low volume, and OFF to 
turn the ringer off. Two-line models have a volume switch for each line. Certain models do 
not have an OFF...

2-334Vo l u m e  C o n t r o l
Chapter 2 - Features and Operation 

3
Attendant Features and
Operation
The Attendant and Attendant(s) with DSS/DLS features of the XTS System are listed and
described in alphabetical order. Attendant features are in addition to digital station
features.
The instructions in this chapter are based on the use of a digital display telephone. 










 
 
 
 
 
 

Introduction3-3
Chapter 3 - Attendant Features and Operation
Introduction
The instructions in this chapter are based on the use of a digital display telephone.
The XTS System provides the following keys, indicators and features:
Handset and Speaker are located at the left side of the front panel. A handset is provided to 
allow confidential conversation when desired. Lifting the handset from its cradle (going 
off-hook) disengages the station’s built-in speaker.
The speaker is located directly below the...

3-4Attendant Features - Index
Chapter 3 - Attendant Features and Operation

MUTE button lets you switch the built-in microphone on or off when using the 
speakerphone, or the handset microphone when using the handset.

HOLD button lets you place an outside caller on hold.
Outside Calls are announced by a tone signal repeated every 3.2 seconds. The 
corresponding outside line indicator flashes slowly.
Intercom Calls can be tone ringing or voice announce. If it is voice announced, the receiving 
station...

Attendant CO Line External (Off-Net) Forward 3-5
Chapter 3 - Attendant Features and Operation
911 Alert
Description
Any station user or attendant who programs a flexible button for 911 ALERT (feature code 
608) will be alerted of internal stations placing 911 calls. The system can store the sixteen 
most recent 911 calls. Calling information includes the time/date of the call, as well as the 
station number from which the call was placed.
The initial 911 Alert indications include:

Audible ringing tone...

3-6Attendant Custom Message
Chapter 3 - Attendant Features and Operation
Operation
To activate off-net forwarding:
1. Dial [603] on the dial pad,
-or-
Press preprogrammed CO OFF-NET FORWARD button.
2. Dial the CO group access code of the group to be forwarded:
[801-823] = CO Group 1-23
[824] = All CO Groups
3. Dial the speed bin number that contains the number where calls are to forward. A 
confirmation tone sounds.
To cancel off-net forwarding:
1. Dial [603] on the dial pad,
-or-
Press preprogrammed CO...

Attendant Custom Message3-7
Chapter 3 - Attendant Features and Operation
2. Enter a valid message bin number [21–30]. The following message displays after the bin 
number has been selected.
3. Enter the custom message using the dial pad keys to enter the letters as shown in
 Figure 2-15 on page 2-214
.

Up to 24 alphanumeric characters may be entered for the custom message (this 
represents 48 digits entered). The actual characters display as the digits are being 
entered while programming the messages....

3-8Attendant Day/Night/Special
Chapter 3 - Attendant Features and Operation
Attendant Day/Night/Special
Description
The system’s Automatic Night Mode Feature can be overridden by the Attendant station. The 
Attendant station user can press their DND button to place the system into Night Mode.
Any designated Attendant can place the system into Night Service.
Operation
1. Press the preprogrammed NIGHT SERVICE button (631, DND by default) once to activate 
the Night mode (LED is lit solid).
2. Press the DND...