Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Station Attributes2-263
Chapter 2 - Features and Operation
Station Attributes
Initialize Station Attributes
Description
The Station Parameters may be initialized setting all data fields to their original, default 
values. The following data fields are returned to their default value upon initializing the 
Station Attributes.
Table 2-22: Station Attribute Defaults
Program 
CodeFlexible
ButtonFeaturesDefault Value
(after initialization)
 FLASH 50 1 Paging Access Enabled
PAGE A 2 Do Not Disturb Enabled
3...

2-264Station Attributes
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button (FLASH 80, Button #3). The following 
message displays:
2. Press the HOLD button. A confirmation tone sounds.
FLASH 50
PA G E  B1 Station Identification 006 (24-Btn Keyset)
6 (SLT w/o MW )
2 Station Day Class of Service (COS) COS 1
3 Station Night Class of Service (COS) COS 1
4 Speakerphone/Headset Programming 0=Full Speakerphone
5 Pick-Up Group(s) Programming Group 1
6 Paging...

Station Attributes2-265
Chapter 2 - Features and Operation
Print Station Attributes
Description
The Print Station Attributes command can be used to print specific flexible station 
parameters or to print the entire database in fixed number order.
The Print Station Attributes command can dump the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
When printing the Station attributes the following...

2-266Station Identification
Chapter 2 - Features and Operation
Programming Steps
1. Press the STATION ATTRIBUTES flexible button (FLASH 85, Button #3). The following 
message displays:
2. To print data for:

All stations, press HOLD.

One station, enter the flexible station number, then press HOLD.
Then the following message displays and the requested information prints:
When the system finishes sending the requested information to the printer, a 
confirmation tone sounds.
Station Identification...

Station Identification2-267
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to...

2-268Station Identification
Chapter 2 - Features and Operation
DEFAULT … All Key Telephone Boards (DTIB) default to ID 006 (24-Button Digital Telephone), 
all Single Line Boards (SLIB) default to ID 6.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Station ID Lock
Description
The Station ID Lock...

Station Message Detail Recording 2-269
Chapter 2 - Features and Operation
Station Message Detail Recording
Description
The XTS station message detail recording (SMDR) provides details on both incoming and 
outgoing calls. This feature is programmable to allow recording of all calls or just outgoing 
long distance calls. The system tracks calls by outside line, number dialed, time-of-day, date, 
station that placed the call and duration of call. Account codes may also be entered and 
recorded.
The SMDR...

2-270 St a tio n  Me ssa g e De ta il  Rec o rd i n g
Chapter 2 - Features and Operation
Figure 2-20: SMDR Printout
80 character format - Outbound Call to a Dialed Number:
1 234 56 7 8
12345678901234567890123456789012345678901234567890123456789012345678901234567890
AAAA BBB HH:MM:SS HH:MM MM/DD/YY HCCCCCCCCCCCCCCCCCCCCCCCC GGGGGGGGGGGG (CR)(LF)
STA   CO TOTAL    START   DATE   DIALED
1100 001 00:00:38 13:57 01/15/01 O2956006
80 character format - Outbound Call to an Extension:
1 234 56 7 8...

Station Message Detail Recording 2-271
Chapter 2 - Features and Operation
The XTS system can provide SMDR output to the optional RS-232C connectors on the MISB. 
When SMDR is desired, the following system-wide parameters determine how SMDR 
information is reported.
Programming Steps
1. Press FLASH and dial [21]. The following message displays:
2. To program SMDR features, use the flexible button(s) as defined in the following 
procedures.
3. The ENABLE/DISABLE, TYPE, and PRINT features toggle on and off...

2-272 St a tio n  Me ssa g e De ta il  Rec o rd i n g
Chapter 2 - Features and Operation
Long Distance / All Calls
Description
The system can be set to record all outgoing calls or only outgoing long distance calls. Long 
Distance calls are defined as beginning with a 1 or 0, or containing eight or more digits. 
Incoming calls are only recorded if TYPE is set for all calls.
Programming Steps
1. Press the CALL TYPE flexible button (FLASH 21, Button #2) to determine the type of calls 
to record. This...