Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Mute Key2-213
Chapter 2 - Features and Operation
5. Press the MUSIC-ON-HOLD flexible button (FLASH 40, Page B, Button #8). The following 
message displays:
6. Enter a valid number on the dial pad to change this feature.
[0] = No Music-On-Hold
[1] = Channel 1
:::::
[8] = Channel 8
7. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … Channel 1 is used for Music-On-Hold.
Mute Key
Description
Pressing the MUTE button while in the speakerphone mode or using the...

2-214Name In Display
Chapter 2 - Features and Operation
Name In Display
Description
The Name in Display feature allows every extension (electronic/digital/SLT) the capability to 
program the users name, for that station, so that people using display telephones see the 
name instead of the station number on their display. The name is programmed at each 
station by the user and may be up to seven letters in length.
Operation
To create your name:
1. Dial [690] on the dial pad.
2. Enter the name (up to 7...

Name In Display2-215
Chapter 2 - Features and Operation
Name / Number Display At Idle
Description
The Name/Number Display feature allows the programmed seven-digit name and station 
number to display together. This option is programmable on a per station basis, however the 
feature must be enabled/disabled in admin programming. If a station has this feature 
enabled but has not programmed a name, the name portion of the LCD is blank. The priority 
of the idle display is UCD/ACD, Hunt, Station/Name, or...

2-216 Na m e / Nu mb e r Tra n sl a ti o n  Ta b l e
Chapter 2 - Features and Operation
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Extension Number
[1] = Name
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Name displays on the LCD.
Conditions
» Not applicable to Single Line Telephones.
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible...

Name / Number Translation Table 2-217
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [55]. The following message displays:
XXX = Table Number 600-799
### = Route Number 000–499
The Route Number LED (Button #1) is lit.
2. Enter a Route Number (000–499) from what was entered in program code, FLASH [43].
To program a phone number into the translation table:
1. Press the PHONE NUMBER flexible button (FLASH 55, Button #2) to enter the desired 
phone number into the translation...

2-218Networking Tables
Chapter 2 - Features and Operation
To locate an existing index for editing:
1. Press the TABLE NUMBER flexible button (FLASH 55, Button #20). The following 
message displays:
2. Enter a valid number that corresponds to the table numbers 600-799.
3. Press HOLD to complete the entry.
Networking Tables
Description
The Networking Table identifies the system number, the CO group, the range of station 
numbers, and the IP address. Details on Networking Tables programming is contained in...

Night Service2-219
Chapter 2 - Features and Operation
Operation
To enter Night Service Mode, from an idle station:
Press the preprogrammed NIGHT SERVICE flexible button [604]. The system is now in the 
Night Service Mode.
To remove Night Service Mode:
Press the preprogrammed NIGHT SERVICE flexible button [604] again. The system is now 
removed from the Night Service Mode.
Automatic / Manual Operation
Description
If the system is operated in the automatic night mode the attendant(s) can override the...

2-220Night Service
Chapter 2 - Features and Operation
Day of Week Programming
Programming Steps
The MONDAY flexible button (Button #2) LED is lit. To change days of the week:
1. Press the appropriate DAY OF WEEK flexible button (FLASH 22, Buttons 2-8).
2. Enter a valid number to indicate the hour and minutes to end night mode.
3. Press HOLD to save the entry. (Example: 07301830 [HOLD]) A confirmation tone sounds 
and the display updates.
Automatic Night Mode Operation
The XTS can be programmed in...

Off-Hook Signaling2-221
Chapter 2 - Features and Operation
Digital Voice Mail (DVM) -- The DVM Day/Night Operation can be set up to follow the same 
path as the Day/Night/Special Mode for the telephone system.
Conditions
» A station using the night key [604] can put the system into night mode.
» The automatic schedule will override the station night key [604].
» The attendant DND setting [631] overrides both the automatic schedule and the station 
night key [604].
Off-Hook Signaling
Description
If a...

2-222Off-Hook Voice Over
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates....