Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Off-Hook Voice Over2-223
Chapter 2 - Features and Operation
Operation
To place an Off-hook Voice Over call:
When an OHVO station calls a busy OHVO station and a busy tone is received, the calling 
OHVO station must press a preprogrammed OHVO button [628] to initiate an OHVO 
announcement, and the following occurs:

The HOLD button LED flashes at the called OHVO station.

The OHVO receiving station receives a one-beep warning tone. The station receiving the 
OHVO call must be off-hook and in H or P mode,...

2-224Off-Hook Voice Over
Chapter 2 - Features and Operation
Conditions
» The station must be in H or P mode to enable this feature.
» The station receiving the OHVO call MUST be off-hook and in H mode.
» The receiving station must have OHVO enabled.
» When the receiving station responds via Camp On, all conditions and options available to 
Camp On apply. (Refer to “Camp On” on page 2-52 for more information).
» OHVO may be used to notify the receiving station of a transferred call (CO Line or 
Intercom)...

Outside Calls2-225
Chapter 2 - Features and Operation
Outside Calls
Operation
To answer an outside call:
1. Lift handset or press ON/OFF button.
2. Press slow flashing OUTSIDE LINE button or LOOP button. (If your phone is programmed 
with Preferred Line Answer, you may answer an outside line by lifting the handset or 
pressing the ON/OFF button.)
To make an outside call:
1. Press OUTSIDE LINE or POOL button. ON/OFF button LED lights and dial tone sounds.
2. Dial the desired party.
3. When called party...

2-226Paging
Chapter 2 - Features and Operation
Operation
If you were given the ability to make page announcements:
1. Lift handset or press ON/OFF button.
2. Press preprogrammed PAGE button,
-or-
Dial the paging code.
[700] = All Call - Internal and External
[701- 708] = Internal Zone 1-8
[709] = Internal All Calls
[760] = External All Calls (All Ext Zones)
[761-762] = External Zone 1-2
[763] = External Zone 3 (MPB2 only)
3. Stations receiving a Page Announcement can press the Volume Bar to change the...

Paging2-227
Chapter 2 - Features and Operation
Paging Access
Description
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-351) to be programmed. If only...

2-228Paging
Chapter 2 - Features and Operation
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Paging - Meet Me
Description
Users may answer a page call from any phone in the system by dialing [770]. The party who 
initiated the page must remain off-hook.
Operation
To request another party meet you...

Paging2-229
Chapter 2 - Features and Operation
Page Warning Tone
Description
The Page Warning Tone determines whether a page warning tone sounds over the Key 
Telephone speakers or external paging speakers, prior to a page announcement.
Programming Steps
1. Press the PAGE WARN TONE flexible button (FLASH 05, Button #5).
2. Enter a valid number (0 or 1) that corresponds with the following:
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Page Warning Tone...

2-230Paging
Chapter 2 - Features and Operation
2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current...

Pause Timer2-231
Chapter 2 - Features and Operation
Pause Timer
Description
When dialing a speed number, a timed pause between digit sending can be placed in the 
number. The length of this pause can be programmed in the system database.
The Pause Timer determines the length of the pause when programmed for use with speed 
dialing and LCR Insert Tables. The Pause Timer setting is variable from 1–9 seconds. There is 
no 0 entry. Using this feature may affect Centrex transfers.
Programing Steps
1. Press...

2-232Personal Messages
Chapter 2 - Features and Operation
2. Dial the 2-digit code for the message that displays. A confirmation tone sounds and the 
DND button LED flashes.
To cancel a pre-assigned message:
1. Either dial the Personal Messages code [633] + [00],  dial [662], or press the DND button.
2. Replace handset. DND button LED extinguishes.
Conditions
» This feature is unavailable at Attendant stations.
» Stations cannot be call forwarded or in DND and have this feature active.
Custom Messages...