Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

LCD2-203
Chapter 2 - Features and Operation
Exclusive Hold
Do Not Disturb
Call Back
Outside Line Transfer
Message Waiting
Reply to a Message Waiting
Programmed Flash Command (F)
Programmed Pause Command (P)
Programmed Pulse-To-Tone 
Switchover (S)
* Features available with optional software
Table 2-18: Liquid Crystal Displays (LCD)
Function CALLING Station Display CALLED Station Display
LINE HOLDING
LINE XXX HH:MM am
DO NOT DISTURB STA XXX
MMM DD YY HH:MM am
DO NOT DISTURB ..(name)..
MMM DD YY HH:MM am...

2-204LCD
Chapter 2 - Features and Operation
CO Line Queuing
Hunt Groups
ACD* or UCD Groups
Ringing CO Lines
Display Security
Station Forwarding Off-Net
Call to Station Forwarded Off-Net
(before and after a call is answered)
Calls in Queue
(supervisor)
Calls in Queue
(using dial code)
ACD* or UCD
* Features available with optional software
Table 2-18: Liquid Crystal Displays (LCD)
Function CALLING Station Display CALLED Station Display
PLACED IN QUEUE FOR
LINE XXX HH:MM am
QUEUE CALL BACK
LINE XXX HH:MM...

LCD2-205
Chapter 2 - Features and Operation
Unavailable Mode (Agent Station)
ACD* or UCD
Station Call to Voice Mail Group Pilot 
Number
Dial By Name
Off-Hook Voice Over (OHVO)
Executive O verride
Voice Mail* Transfer with ID Digits
Repeat Redial
Call Coverage Station
(after call is answered at coverage 
station in a non-network system or 
within same Node)
(after call is answered at coverage 
station in a network with a call 
passed across a switch)
Name/Number Display at Idle
* Features available with...

2-206Leading Digit
Chapter 2 - Features and Operation
Leading Digit
Description
System administrators can tailor the system numbering plan to change all 3-digit numbers 
into 4-digit numbers that begin with a desired digit 0-8.
Programming Steps
1. Press FLASH and dial [09]. The following message displays:
2. Press Button #9. The following message displays:
3. Dial a valid number (0-8) to identify the desired leading digit.
4. Press HOLD to save the entry.
Scrollable Canned Messages
ACD* Transfer...

Least Cost Routing2-207
Chapter 2 - Features and Operation
Least Cost Routing
For information about Least Cost Routing (LCR), refer to Appendix B, “Least Cost Routing.” 

2-208Least Cost Routing
Chapter 2 - Features and Operation
INTENTIONALLY BLANK 

Message Wait2-209
Chapter 2 - Features and Operation
Message Wait
Description
Stations that are busy, unattended, or in DND can be left a message indication by other 
stations in the system. Up to five messages can be left at one keyset. Upon return to the 
station, the user can press the flashing MSG WAIT button to ring each party in sequential 
order.
Operation
To leave a message waiting indication:
If you dial a station that is busy, unattended, or in DND, you can leave a message waiting 
indication....

2-210 Mes sa ge  Wa it in g  Re mi nd e r To n e
Chapter 2 - Features and Operation
Message Waiting Reminder Tone
Description
The Message Wait Reminder Timer determines the time between repeated reminder tones to 
a key telephone with a message waiting. Digital station users may be reminded of a message 
waiting on their telephone with an audible signal presented at a timed interval. The Message 
Wait Reminder Tone setting is variable from 000-104 minutes.
Programming Steps
1. Press the MESSAGE WAIT...

Music-On-Hold2-211
Chapter 2 - Features and Operation
A maximum of 8 channels are available for use on the system. By default, no channels are 
assigned.
Figure 2-14: Wiring - Music Source to a CO Line
Programming Steps
1. Press the MUSIC CH # flexible button (FLASH 09, Button #1 through #6). The following 
message displays:
X= 4-8
XXX = Maximum CO Lines in your system
YYY = CO Line number selected for use with channel X
2. Enter a valid number (001-XXX) that corresponds to the CO line number desired.
3....

2-212Music-On-Hold
Chapter 2 - Features and Operation
Programming Steps
1. Press MUSIC-ON-HOLD flexible button (FLASH 05, Button #12). Feature toggles on/off 
each time button is pressed; and the display updates.
[0] = Disabled
[1] = Enabled
2. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Music-On-Hold is enabled.
Music-On-Hold (per CO Line)
Description
The Music-On-HOLD feature allows a user to select the Music-On-Hold channel for each CO 
line. This feature lets the system assign...