Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

ISDN Programming - Page A2-183
Chapter 2 - Features and Operation
DEFAULT … ITU (ISDN plan)
Nortel DMS 100 Only
1. Change Flash 45, button 10 (Numbering Plan) to CO by dialing 1 HOLD.
2. Set the definition in the DMS 100 Central Office Switch.

The DMS 100 Office refers to this switch as National or N12 Standard so they know 
not to look at this parameter in their switch.

LTDEF should be set to NI PRI N12 V1.
Calling Number
Description
0 disables the calling party number from being sent to the CO. 1...

2-184ISDN Programming - Page A
Chapter 2 - Features and Operation
2. Enter a valid number (0-2) on the dial pad.
[0] = Normal mode
[1] = Near end mode
[2] = Far end mode
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT … Loopback setting is normal.
BRI 10-Digit Number Plan
Description
The BRI 10-Digit Number Plan is the specific plan that a particular Central Office uses for 
10-digit BRI calls.
Programming Steps
1. Press the BRI 10 DIGIT No PLAN flexible button...

ISDN Programming - Page B2-185
Chapter 2 - Features and Operation
DEFAULT … BRI 11-Digit Number Plan setting is ITU.
ISDN Programming - Page B
Description
When entering the ISDN attributes portion of the database, the programmer may decide to 
enter information for a range of slots or one specific slot. Range programming lets the 
programmer change a specific parameter or a few parameters for an entire range of slots, 
leaving intact the remaining data fields that do not require change. Those data fields...

2-186ISDN Programming - Page B
Chapter 2 - Features and Operation
4. Press button #20 to select Page B. The following message displays to indicate current 
programming of that slot or group of slots:
XY-XY = Slot Range
X = Cabinet (0, 1, 2)
Y = Slot (0-8)
NOTE -- Slot 8, Cabinet 0 is reserved for the MISB
Maximum Number Retransmission
Description
The Maximum Number of Retransmissions of a frame (N200) is a system parameter. Do not 
change the Maximum Number Retransmission setting unless advised to do so...

ISDN Programming - Page B2-187
Chapter 2 - Features and Operation
Maximum TEI Request
Description
This feature is reserved for future use.
Programming Steps
1. Press the MAX TEI RQST flexible button (FLASH 45, Page B, Button #3).
2. Enter a valid number (000-999) on the dial pad.
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT … Maximum TEI Request setting is 003.
Maximum XID Retransmission
Description
Do not change the Maximum number of XID Retransmissions setting...

2-188ISDN Programming - Page B
Chapter 2 - Features and Operation
Minimum TEI ID Check Message
Description
The Minimum TEI ID Check Message feature sets the minimum time between retransmission 
of the TEI identity check messages. Do not change the Minimum TEI ID Check Message 
setting unless advised to do so by Technical Support.
Programming Steps
1. Press the MIN TEI ID CHK MSG flexible button (FLASH 45, Page B, Button #6).
2. Enter a valid number (00-99 seconds) on the dial pad.
3. Press the HOLD...

ISDN Programming - Page B2-189
Chapter 2 - Features and Operation
Programming Steps
1. Press the MSG EXCHANGE TIMER flexible button (FLASH 45, Page B, Button #8).
2. Enter a valid number (00-99 seconds) on the dial pad.
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT … Message Exchange Timer setting is 15 seconds.
Minimum XID Retransmission
Description
The Minimum XID Retransmission setting establishes the minimum time between XID 
messages. Do not change the Minimum...

2-190ISDN Programming - Page B
Chapter 2 - Features and Operation
Set-Up Timer
Description
The Set-up Timer setting establishes the response time to setup message. Do not change the 
Set-up Timer setting unless advised to do so by Technical Support.
Programming Steps
1. Press the SET UP TIMER flexible button (FLASH 45, Page B, Button #11).
2. Enter a valid number (00-99 seconds) on the dial pad.
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT … Set-up Timer setting...

ISDN Programming - Page B2-191
Chapter 2 - Features and Operation
Release Request
Description
Do not change the Release Request setting unless advised to do so by Technical Support.
Programming Steps
1. Press the RELEASE REQUEST flexible button (FLASH 45, Page B, Button #13).
2. Enter a valid number (00-99 seconds) on the dial pad.
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT … Release Request Timer setting is 4 seconds.
Link Disconnect
Description
Do not change...

2-192ISDN Programming - Page B
Chapter 2 - Features and Operation
Connect Request
Description
Do not change the Connect Request Timer setting unless advised to do so by Technical 
Support.
Programming Steps
1. Press the CONNECT REQUEST flexible button (FLASH 45, Page B, Button #16).
2. Enter a valid number (00-99 seconds) on the dial pad.
3. Press the HOLD button. A confirmation tone sounds and the display updates.
DEFAULT … Connect Request setting is 4 seconds.
Restart Request Timer
Description
Do not...