Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Executive Override2-143
Chapter 2 - Features and Operation
4. Press the EXECUTIVE OVERRIDE BLOCK flexible button (Button #13). The following 
message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Executive Override Blocking is disabled at all stations.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51...

2-144Executive Override
Chapter 2 - Features and Operation
Barge-In Warn Tone
Description
When the Barge-in Warn Tone feature is enabled, it produces a tone to notify a station that 
another station is about to use Executive Override or the Barge-in feature to cut into the 
existing conversation.
Programming Steps
1. Press the BARGE IN WARN TONE flexible button (FLASH 06, Button #1). The following 
message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the conference tone.
[0] = Disabled...

Executive / Secretary Pairs2-145
Chapter 2 - Features and Operation
Executive / Secretary Pairs
Description
There are four Executive/Secretary pairs available. When an Executive station is busy or in 
DND, intercom calls and transfers are automatically routed to the designated Secretary.
The assigned secretary may Camp On to the Executive Station when the station is busy or in 
Do-Not-Disturb. There can be only one pairing of stations, with no duplicates. You cannot 
pair Executive 100 to Secretary 101,...

2-146External Day Ring
Chapter 2 - Features and Operation
External Day Ring
Description
The system can be programmed so CO lines marked for UDA provides ringing out of the 
external page ports when the system is in the Day Mode.
Programming Steps
1. Press the EXT DAY RING flexible button (FLASH 06, Button #5). The following message 
displays:
2. Enter a 0 or 1 on the dial pad to enable/disable External Day Ring.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds....

Fixed Station/Port Number2-147
Chapter 2 - Features and Operation
Fixed Station/Port Number
Description
When a station dials the feature code 611 on a display telephone, it will display the Fixed 
Station/Port Number for that telephone. For example, when using flexible numbering some 
programming steps require the “FIXED” code. This code allows you to dial 611 and quickly 
determine the fixed port for that station.

SINGLE LINE TELEPHONE
Not applicable
Flash Rates (Programmable)
Description
Fixed and...

2-148Flexible Button Assignment
Chapter 2 - Features and Operation
Flexible Button Assignment 
Description
If you have buttons on your telephone, you may program them to suit your own needs. This 
feature also allows programming of flexible buttons from a remote location (off-site). Range 
programming can also assign these buttons to multiple stations.
The possible functions you may assign to these buttons include:

Outside Line -- Automatically accesses assigned line. (User programmable)

DSS/BLF --...

Flexible Button Assignment2-149
Chapter 2 - Features and Operation
A CO line can be assigned a number between 001 and the maximum number of CO lines 
in the system. Additional stations can be added to the system by reducing the number of 
CO lines.
Flexible Button
Description
Each Digital Telephone has 8, 12, or 24 flexible buttons that can be programmed. One of the 
following six operations can be selected in programming for each button.
To assign a Flexible Button (user programmable):
Enter [BB], [0],...

2-150Flexible Button Assignment
Chapter 2 - Features and Operation
This feature enables flexible buttons to be programmed from a remote location (refer to 
“Default Numbering Plan” on page F-16). Range programming can be used to assign these 
buttons to multiple stations. When a button is assigned as a feature button [4], the 
programmer can program any features on the buttons.
To unassign (lock out) a button:
Enter [BB], [#], [HOLD]
If SLT stations must be programmed for off-hook preference, program the...

Flexible Button Assignment2-151
Chapter 2 - Features and Operation
8-BUTTON DEFAULT
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-351) to be...

2-152Flexible Button Assignment
Chapter 2 - Features and Operation
4. Press button #20. The display updates to reflect current programming for Page B.
5. Press the BUTTON ASSIGN flexible button (Button #11). The following message displays:
6. Enter a valid button number [01-24] to program followed by the desired button function:
[0] = Flexible/user changeable
[1] = CO line
[2] = Loop button/all-purpose CO appearance
[3] = Pool for specific groups
[4] = Direct feature programmable (for DSS/BLF, use [4] +...