Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

Database Administration2-103
Chapter 2 - Features and Operation
4. Press button #20. The display updates to reflect current programming for Page B.
5. Press the CORDLESS KEY flexible button (Button #17) to assign the FEAT Buttons. The 
following message displays:
XX = Assigned FEAT Button (01-24 = Button 1-24, 01-30 for Large Screen Display telephone)
00 = None
DEFAULT … No button (00) is assigned to the FEAT.
Conditions
» Only one station at a time can be programmed when using a flexible station...

2-104Database Administration
Chapter 2 - Features and Operation
Programming Steps
1. Press FLASH and dial [50] or dial [51]. Flexible button #24 (New Range) is lit and one of 
the following messages displays:
2. Enter the range of fixed station numbers (100-351) to be programmed. If only one station 
is being programmed, enter that number twice, e.g., [100 100].
-or-
Enter a valid flexible number (100-8999) to be programmed.
3. Press HOLD to save the entry. A confirmation tone sounds and the display...

Database Administration2-105
Chapter 2 - Features and Operation
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Administration Password
Description
The password used to enter customer database programming can be customized by the 
programmer. This lets the system administrator block unauthorized personnel from...

2-106Database Printout (Dump)
Chapter 2 - Features and Operation
Database Printout (Dump)
Description
Through a system programming command, either portions of or a complete database dump 
can be printed using the RS-232C connector located on the Master Processor Board (MPB), on 
the XTS.
The Print System Database command dumps the entire database as a permanent record 
which can serve as a hardcopy of the database. The system baud rate must match that of the 
printer or receiving device.
Printing the...

Dial Pulse Sending2-107
Chapter 2 - Features and Operation
Dial Pulse Sending
Description
Each CO interface circuit for outside lines can be programmed to send dial pulse or DTMF 
signals. Dialing speed and break/make ratios are programmable.
Dial Pulse Parameters
Description
The Dial Pulse option lets the installer adjust the dial pulse ratio and speed when using dial 
pulse (rotary) type signaling. By default, all lines are DTMF (tone) signaling. If pulse dialing is 
required, the individual outside...

2-108Direct Inward Dialing
Chapter 2 - Features and Operation
Pulse Dial Inter-Digit Timer
Description
This governs the inter-digit time of the Pulse Dial Digits, rotary dial mode. The Pulse Dial Ring 
Timer setting is variable from 300-600 ms.
Programming Steps
1. Press the PULSE DIAL I/D TIMER flexible button (FLASH 02, Button #5). The following 
message displays:
2. Enter a valid number on the dial pad that corresponds to 300-600 ms.
3. Press HOLD to save the entry. A confirmation tone sounds and the...

Direct Inward Dialing2-109
Chapter 2 - Features and Operation
If the outside caller disconnects from a two-party conversation, the Central Office opens the 
loop and returns the line to idle state. The XTS Digital System detects the disconnect signal, 
release the line, and provides a busy tone to the keyset/SLT (unless the SLT is a VM port), and 
disconnects from the DID line. If the extension called hangs up the phone, the central office 
detects disconnects, and returns the line to the idle state....

2-110Direct Inward Dialing
Chapter 2 - Features and Operation
Route 000 in the ICLID Ringing Assignment Table is used as the intercept route. Calls to 
numbers not contained in the DID table follow Route 000. If Route 000 is defaulted to None, 
the call follows Route 001.
Route 001 is used as the Busy DID Route. DO NOT program any entries in this Route if you 
intend to provide a busy tone to callers dialing a busy DID/DVIS number.
Programming Steps
Press FLASH and dial [44]. The following message...

Direct Inward Dialing2-111
Chapter 2 - Features and Operation
To change to a different DID Route Number:
1. Press either the UP Button (FLASH 44, Button #18),
-or-
Press the DOWN Button (FLASH 44, Button #19).
2. Enter a valid Route Number (000-499) to be associated with the DID Number.
This Route Number is the same Route Number in the ICLID Ringing Assignments Table 
(FLASH 43) and determines the destination of the DID number associated with this 
Route Number. The display shows the route number as it...

2-112Direct Inward Dialing
Chapter 2 - Features and Operation
Name Assigned to DID Number
Programming Steps
1. Press the NAME flexible button (FLASH 44, Button #3) to enter the desired name for the 
DID trunk. Maximum length is 8-characters.
2. Press the HOLD button to update the database. A confirmation tone sounds.
3. Use the BACK SPACE flexible button (FLASH 44, Button #5) to erase the current letter to 
correct for errors.
DID Name and Number Codes
The display shows the DID name or number as it is...