Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

CO Line Group2-73
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 is lit. The display updates to reflect current programming for Page A:
4. Press button #20. The display updates to reflect current programming for Page B.
5. Press the CO LINE GROUP ACCESS flexible button (Button #8). The following message 
displays:
6. To add a Line Group, enter a valid number (00, or 01–23) to designate the outside line 
groups...

2-74CO Line Group
Chapter 2 - Features and Operation
CO Line Group Programming
Description
Twenty four line groups are available for CO line assignment. Groups should be assigned 
according to type (local, FX, WATS, etc.). All unassigned CO lines should be programmed into 
a different group so they are not accessed by Line Queuing, Pooled Group access (Pool 
Buttons), Speed Dial, or LCR features.
Any Line Group can be used for programming a line(s) as private; for private lines, assign Line 
Group access...

CO Line - Identification2-75
Chapter 2 - Features and Operation
CO Line - Identification
Description
The CO Line Identification feature allows entering a name into the database for each 
individual line (trunk) connected to the system. The name may be entered in any 
combination up to 12-characters in length (this represents 24 digits entered). When the CO 
line identification field is programmed, display telephones receive the identification field in 
place of the default field (LINE XXX).
SMDR always...

2-76CO Line - Identification
Chapter 2 - Features and Operation
Programming Steps
Each CO line can be programmed to have a name associated to it in database programming.
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following...

CO Line - Incoming Ringing Assignment 2-77
Chapter 2 - Features and Operation
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
CO Line - Incoming Ringing Assignment
Description
Each CO line may be programmed (in database admin) so that incoming ringing on the 
specified CO line(s) may be assigned initial ringing to one of the following destinations:

One or more stations (Keyset or SLT )

An ACD, UCD, Voice Mail or Hunt Group

Off-Net (via Speed Dial)
The ring-in...

2-78 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the RING ASSIGNMENT flexible button...

CO Line - Incoming Ringing Assignment 2-79
Chapter 2 - Features and Operation
To add multiple stations:
Enter: DDDDR HOLD DDDDR HOLD DDDDR HOLD...etc.
(Example: 10073 HOLD, 10083 HOLD, 10093 HOLD)
To delete a single station:
Enter: DDDD0 HOLD
(Example: 10080 HOLD)
To delete multiple stations:
Enter: DDDD0 HOLD DDDD0 HOLD...etc.
(Example: 10080 HOLD, 10090 HOLD)
DEFAULT … All CO lines ring at the Attendant, Station 100 during Day and Night Modes.
Incoming CO Line Ringing - Setting Flash Rate
Description...

2-80 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
2. Enter a valid number for the range of lines being programmed. If only one line is being 
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates. 
Flexible button #19 (Page A) is lit. The following message displays to indicate current 
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press FLASH 40, Page A, Button #13 to display...

CO Line - Incoming Ringing Assignment 2-81
Chapter 2 - Features and Operation
Release Timer
Description
The Release Timer option allows the user to adjust the release timer on a per CO Line basis. 
The release timer is used on ground start type trunks.
This timer is a lead filter timer. The CO must remove ground from the tip lead for longer than 
this timer in order for the system to recognize it.
Programming Steps
1. Press FLASH and dial [40]. The following message displays:
2. Enter a valid number for...

2-82 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
Reseize Timer
Description
The Reseize Timer option lets the user adjust the Reseize Timer on a per CO Line basis. The 
Reseize Timer can be used on any trunk type. This timer sets the time period that a trunk is 
held disconnected after receiving a disconnect before being reseized when a device is 
queued for a member of the trunk group.
Programming Steps
1. Press the RESEIZE TIMER Button (FLASH 40, Page C, Button #5) in the...