Starplus Triad Xts Digital Key Telephone System System Programming And Operation Manual

CO Line - Ringing Options2-93
Chapter 2 - Features and Operation
Queued CO Ringing Flash Rate
Description
The Queued CO Ringing flash rate is the rate at which a CO Line button or Loop button 
flashes when a queued line becomes available. This flash rate can be programmed to 
29 different options identified in the flash rate table. This enables the programmer to 
customize the key system configuration to desired flash rates.
Programming Steps
1. Press the QUEUED CO RING flexible button (FLASH 07, Button...

2-94CO Line - Ringing Options
Chapter 2 - Features and Operation
CO Direction
Description
CO Lines can be programmed on a per CO Line basis for the type of CO Line desired:
Incoming

Incoming restricts the CO Line for incoming calls only.

Users can place call on hold, park the call, and other stations can pick up the call.
Outgoing

Outgoing restricts the CO Line to outgoing calls only.

Users can place call on hold, park the call, and other stations can pick up the call.
Incoming and Outgoing

Incoming...

CO Port Parameters2-95
Chapter 2 - Features and Operation
5. Enter a valid number (0-3) on the dial pad which corresponds to the desired CO type:
[0] = Out-of-Service (OOS)
[1] = Incoming Only
[2] = Outgoing Only
[3] = Both Incoming and Outgoing
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT … All CO Lines default to both incoming and outgoing type.
Conditions
» For PRI cards, the 24th channel must be marked as Out-of-Service (OOS). This is true on all 
PRI...

2-96CO Port Parameters
Chapter 2 - Features and Operation
Print CO Port Parameters and Feature Codes
Description
The Print CO Port Parameters and Feature Codes command dumps the entire database as a 
permanent record which can serve as a hardcopy of the database. The system baud rate must 
match that of the printer or receiving device.
Figure 2-5: CO Port Attributes Printout
Programming Steps
1. Press the CO PORT flexible button (FLASH 85, Button #4). The following message 
displays:
2. To print the CO...

CO Ring Detect Timer2-97
Chapter 2 - Features and Operation
CO Ring Detect Timer
Description
The CO Ring Detect Timer controls the time necessary to detect an outside line ringing into 
the system. The duration of the ringing signal from the CO or the PBX is matched with ringing 
detection circuitry in the XTS. The ring detect can range from 200 ms to 900 ms programmed 
in 100 ms increments. This timer helps prevent false ringing.
Programming Steps
1. Press the CO RING DETECT TIMER flexible button (FLASH...

2-98Conference
Chapter 2 - Features and Operation
Conference Enable/Disable
Description
The Conference Enable/Disable feature allows administering of the system conference 
feature on a per station basis for the ability of a station to initiate a conference.
Use Flash 50 programming when you want to modify a range of stations’ attributes using 
fixed station numbers.
Use Flash 51 programming to modify a single station’s attributes using a flexible station 
number.
Programming Steps
1. Press FLASH and...

Conference2-99
Chapter 2 - Features and Operation
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT … Conference is enabled.
Conditions
» Only one station at a time can be programmed when using a flexible station number.
» When in Flash 51 programming, if you press HOLD without specifying a flexible number 
to be programmed, you will get the station that is in port/station 100.
Conference /...

2-100Conference
Chapter 2 - Features and Operation
Conference Combinations
Description
Only stations that have conference enabled can institute a conference.

Add-On Conference -- Up to eight internal parties can engage in a conference, or seven 
internal parties with one external party.

Multi-Line Conference -- One internal station can engage in a conference with up to four 
outside parties.
Capacities
The total number of conferences that can be conducted simultaneously system-wide 
depends upon...

Conference2-101
Chapter 2 - Features and Operation
3 -- Press CONF and hang up or press the ON/OFF button to leave the other conference 
parties still connected in an unsupervised conference. The CONF button flashes and the 
timer starts. There is a warning tone before the other parties are dropped.
To re-enter a Conference:
When the controller re-enters the conference, the disconnect timer is reset.
1. Lift handset to re-enter a monitored conference.
2. To re-enter a conference placed on hold, repeat...

2-102 Co rd l e ss Key Te le ph o ne  Un it  Fea tu re  But to n
Chapter 2 - Features and Operation
Cordless Key Telephone Unit Feature Button
Description
If a Cordless Key Telephone Unit (CKTU) is associated with the station, the FEAT Button on the 
CKTU may be assigned to function as any one (1) of the 24 Flexible Buttons on the telephone. 
This programming area defines which Flexible Button on the telephone is applied to the 
CKTU FEAT Button. Not all features are available to be assigned to the CKTU...